Analysis of dynamics and prediction of reliability indicators of a cooling thermoelement with the predefined geometry of branches

Authors

DOI:

https://doi.org/10.15587/1729-4061.2018.123890

Keywords:

thermoelectric cooler, geometry of thermoelements, time required to enter a stationary mode, reliability indicators

Abstract

We have investigated the influence of structural and technological elements on the basic parameters, reliability indicators, and the dynamics of operation of thermoelectric cooling devices under various current modes within the operating range of temperature differences. We analyzed the ratios of correlation between the time required to enter a stationary mode and relative intensity of failures in a cooler, and energy indicators, thermoelectric parameters of thermoelements, structural and technological indicators.

An analysis of the time required to enter a stationary mode was performed for different modes of operation from the maximum cooling capacity to the minimum failure rate. It is shown that in order to reduce the time required for a cooler to enter a stationary mode, at the predefined geometry of thermoelements and temperature difference, it is necessary to employ the mode of maximum cooling capacity.

The quantitative analysis showed that at the predefined geometry of thermoelements branches the time required to enter a stationary working mode does not depend on the number of thermoelements in a thermoelectric cooler. At a difference of temperatures close to the maximum value, the time required to enter a stationary working mode differs slightly for all modes of operation. Comparative analysis of the basic parameters of reliability indicators and dynamical characteristics makes it possible to find compromise solutions when constructing thermoelectric devices taking into consideration the weight of each of the constraints.

From a practical point of view, the results obtained suggest that increasing the cooling rate does not require changes to the existing technology for making thermoelectric coolers. Control over performance speed during transition from one stationary state to another state is executed through the selection of current modes in the operation of a thermoelectric device. In this case, there is a possibility to choose the conditions under which reliability indicators match the permissible limit.

Author Biographies

Vladimir Zaykov, State Enterprise «Research Institute «SHTORM» Tereshkovoi str., 27, Odessa, Ukraine, 65076

PhD, Head of Sector

Vladimir Mescheryakov, Odessa State Environmental University Lvivska str., 15, Odessa, Ukraine, 65016

Doctor of Technical Sciences, Professor, Head of Department

Department of Informatics

Yurii Zhuravlov, National University «Odessa Maritime Academy» Didrikhsona str., 8, Odessa, Ukraine, 65029

PhD, Associate Professor

Department of Technology of Materials and Ship Repair

Dmitry Mescheryakov, JSC Petrosoft Lustdorfska road, 19, Odessa, Ukraine, 65059

Customer Support Manager

References

  1. Shalumova, N. A., Shalumov, A. S., Martynov, O. Yu., Bagayeva, T. A. (2011). Analysis and provision of thermal characteristics of radioelectronic facilities using the subsystem ASONIKA-T. Advances in modern radio electronics, 1, 42–49.
  2. Zebarjadi, M., Esfarjani, K., Dresselhaus, M. S., Ren, Z. F., Chen, G. (2012). Perspectives on thermoelectrics: from fundamentals to device applications. Energy & Environmental Science, 5 (1), 5147–5162. doi: https://doi.org/10.1039/c1ee02497c
  3. Kofanov, Yu. N. et. al. (2014). System problems of reliability, quality, mathematical modeling and intelligent technologies in innovative projects. Moscow: HRU HES, 532.
  4. Ndao, S., Peles, Y., Jensen, M. K. (2009). Multi-objective thermal design optimization and comparative analysis of electronics cooling technologies. International Journal of Heat and Mass Transfer, 52 (19-20), 4317–4326. doi: https://doi.org/10.1016/j.ijheatmasstransfer.2009.03.069
  5. Thermoelectric modules market. Analytical review (2009). RosBussinessConsalting, 92.
  6. Sootsman, J. R., Chung, D. Y., Kanatzidis, M. G. (2009). New and Old Concepts in Thermoelectric Materials. Angewandte Chemie International Edition, 48 (46), 8616–8639. doi: https://doi.org/10.1002/anie.200900598
  7. Rowe, D. M. (Ed.) (2012). Materials, Preparation, and Characterization in Thermoelectrics. Vol. 1. Boca Raton: CRC Press, 544.
  8. Zhang, L., Wu, Z., Xu, X., Xu, H., Wu, Y., Li, P., Yang, P. (2010). Approach on thermoelectricity reliability of board-level backplane based on the orthogonal experiment design. International Journal of Materials and Structural Integrity, 4 (2/3/4), 170. doi: https://doi.org/10.1504/ijmsi.2010.035205
  9. Choi, H.-S., Seo, W.-S., Choi, D.-K. (2011). Prediction of reliability on thermoelectric module through accelerated life test and Physics-of-failure. Electronic Materials Letters, 7 (3), 271–275. doi: https://doi.org/10.1007/s13391-011-0917-x
  10. Wereszczak, A. A., Wang, H. (2011). Thermoelectric Mechanical Reliability. Vehicle Technologies Annual Merit Reviewand Peer Evaluation Meeting. Arlington, 18.
  11. Singh. R. (2008). Experimental Characterization of Thin Film Thermoelectric Materials and Film Deposition VIA Molecular Beam Epitaxial. University of California, 54.
  12. Zaykov, V., Mescheryakov, V., Zhuravlov, Y. (2017). Analysis of the possibility to control the inertia of the thermoelectric cooler. Eastern-European Journal of Enterprise Technologies, 6 (8 (90)), 17–24. doi: https://doi.org/10.15587/1729-4061.2017.116005
  13. Zaykov, V. P., Kinshova, L. A., Moiseev, V. F. (2009). Prediction of reliability on thermoelectric cooling devices. Kn. 1 Single-stage devices. Odessa: Politehperiodika, 120.

Downloads

Published

2018-10-05

How to Cite

Zaykov, V., Mescheryakov, V., Zhuravlov, Y., & Mescheryakov, D. (2018). Analysis of dynamics and prediction of reliability indicators of a cooling thermoelement with the predefined geometry of branches. Eastern-European Journal of Enterprise Technologies, 5(8 (95), 41–51. https://doi.org/10.15587/1729-4061.2018.123890

Issue

Section

Energy-saving technologies and equipment