Influence research of profile chords ratio on aerodynamic characteristics of tandem compressor cascade
DOI:
https://doi.org/10.15587/1729-4061.2015.50535Keywords:
simulation, angle of attack, tandem cascade, stall, compressor, flow, aerodynamic characteristics, viscosityAbstract
Efficiency improvement of gas turbine compressors is ensured by the extensive use of tandem blade rows in straightener blades of the last stages of multistage axial compressors. Their installation provides large flow deflection angles in the unstalled flow of blade rows and, consequently, a low level of losses in the design mode of the compressor. The problem of influence research of the first- and second-row blade chords ratio in tandem blade rows in a wide range of angles of attack is relevant and is of practical interest in developing recommendations for ensuring the gas-dynamic stability of gas turbine compressors. To solve the problem, the method of the computational experiment was used and characteristics of tandem compressor cascade with different first- and second-row blade chords ratios were calculated in the paper. The calculation results of the characteristics of tandem cascade were compared with the characteristics of an equivalent single compressor cascade. For the computational domain of the studied tandem and equivalent single cascades, small adaptive unstructured grid and the second-order design scheme with the local use of the first-order design scheme (High resolution) was applied. The Menter's SST model was used to solve the problems. The results showed that the aerodynamic characteristics of the tandem compressor cascades essentially depend on the first- and second-row blade chords ratio. With positive angles of attack, the quality parameter of tandem cascades is higher than that of single, with the first- and second-row blade chords ratio, corresponding to the position of the slot xщ=(0,3 ... 0,4)b∑. With negative angles of attack, the quality parameter of tandem cascades is higher than that of single, with the first- and second-row blade chords ratio, corresponding to the position of the slot xщ=(0,5 ... 0,7)b∑.
References
- Теrеschenko, Yu. М. (1987). Ajerodinamicheskoe sovershenstvovanie lopatochnyh apparatov kompressorov. Moscow, USSR: Mashinostroenie, 168.
- Gostelou, Dzh. (1987). Ajerodinamika reshetok turbomashin. Moscow, USSR: Mir, 392.
- Chen, N. (2010) Aerothermodynamics of turbomachinery: analysis and design. Singapure: John Wiley & Sons Pte Ltd, 461. doi: 10.1002/9780470825020
- Fikkert, K. (1953) Issledovanie difuzornyh reshetok s bol'shim otkloneniem potoka. Voprosi raketnoj tehniki, 1, 57–67.
- McGlumphy, J., Wing-Fai, Ng, Steven, R., Kempf, W., Kempf ,S. (2010). 3D Numerical Investigation of Tandem Airfoils for a Core Compressor Rotor. Journal of Turbomachinery, 132 (3), 1–9. doi: 10.1115/1.3149283
- Zhao, S., Luo, J., Lu, X., Zhu, J. (2010). Exploring the intention of using aspirated cascade to replace tandem cascades. Journal of Thermal Science, 19 (5), 390-396. doi: 10.1007/s11630-010-0399-4
- Lee, T. (2011). Flow past two in-tandem airfoils undergoing sinusoidal oscillations. Experiments in Fluids, 51 (6), 1605–1621. doi: 10.1007/s00348-011-1173-4
- Shen, C., Qiang, X., Teng, J. (2012). Numerical and experimental investigation of an axial compressor flow with tandem cascade. Journal of Thermal Science, 21 (6), 500–508. doi: 10.1007/s11630-012-0574-x
- Qiushi, L., Hong W., Sheng Zh. (2010). Application of tandem cascade to design of fan stator with supersonic inflow. Chinese Journal of Aeronautics, 23 (1), 9–14. doi: 10.1016/s1000-9361(09)60181-3
- Menter, F. R. (1994). Two-equation eddy viscosity turbulence models for engineering applications. AIAA Journal, 32 (8), 1598–1605. doi: 10.2514/3.12149
- Tereshсhenko, Ju. M., Doroshenko, E. V., Abolhassan zade, Dzh. (2015). Modelirovanie techenija v dvuhrjadnyh lopatochnyh vencah. Vіsnik Nacіonal'nogo tehnіchnogo unіversitetu "HPІ". Serіja: Mehanіko-tehnologіchnі sistemi ta kompleksi, 22, 75–77.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2015 заде Джалал Аболхассан, Юрий Матвеевич Терещенко, Екатерина Викторовна Дорошенко
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.