The study of dynamic load on a wagon–platform at a shunting collision
DOI:
https://doi.org/10.15587/1729-4061.2016.72054Keywords:
wagon-platform, bearing structure, container, dynamics, simulation, shunting collision, construction load, acceleration, combined transportationAbstract
In order to increase the volume of cargo transportation through international transport corridors that pass through Ukraine, container transportation has been developed. To ensure the safety of a wagon-platform with containers placed on it, the research of dynamic loads acting on them at shunting collision has been conducted in real operating conditions.
The research results led to the conclusion that the largest values of acceleration acting on the wagon-platform with containers placed on it during a shunting collision occur in the presence of gaps between the fitting stops and fittings and amount, respectively, about 90 m/s² and 110 m/s².
The approbation of obtained acceleration values was performed by computer simulation of the dynamics of a wagon platform with containers placed on it under the action of the longitudinal impact force of 3.5 MN on the back gauge of automatic coupling.
Verification of the model was tested by the Fischer criterion. This revealed that the hypothesis of the adequacy of the model was not disputed.
Conducted research will improve operational safety of the wagons in the combined transportation, and will motivate design of wagons of the new generation for use in combined international traffic.
References
- Myamlin, S. V., Shatunov, A. V., Sorokolet, A. V. (2010). Podvizhnoy sostav dlya perevozki konteynerov zheleznodorozhnyim transportom. Sb. nauch. trudov DonIZhTa, 22, 125–132.
- Chlus, K., Krason, W. (2011). Dynamic analysis of railway platform chassis model. Journal of KONES Powertrain and Transport, 18 (2), 3–100.
- Chłus, K., Krasoń, W. (2015). Numerical standard tests of railway carriage platform. Journal of KONES. Powertrain and Transport, 19 (3), 59–64. doi: 10.5604/12314005.1137944
- New livery for tarmac wagons (2011). Online, 17, 1.
- Switching over to the home platform (2015). Journal for partners Transmashholding, 3, 22–23.
- Nader, M., Sala, M., Korzeb, J., Kostrzewski, A. (2014). Kolejowy wagon transportowy jako nowatorskie, innowacyjne rozwiązanie konstrukcyjne do przewozu naczep siodłowych i zestawów drogowych dla transportu intermodalnego. Logistyka. 4, 2272–2279.
- Niezgoda, T., Krasoń, W., Stankiewicz, M. (2015). Simulations of motion of prototype railway wagon with rotatable loading floor carried out in msc adams software. Journal of KONES. Powertrain and Transport, 19 (4), 495–502. doi: 10.5604/12314005.1138622
- Bubnov, V. M., Myamlin, S. V., Gurzhi, N. L. (2009). Eksperimentalnyie issledovaniya sharnirno soedinennogo vagona – platformyi dlya krupno – tonnazhnyih konteynerov modeli 13 – 1839. Visnik Dnipropetrovskogo natsionalnogo universitetu zaliznichnogo transportu imeni akademika V. Lazaryana, 28, 12–16.
- Bogomaz, G. I., Mehov, D. D., Pilipchenko, O. P., Chernomashentseva, Yu. G. (1992). Nagruzhennost konteynerov-tsistern, raspolozhennyih na zheleznodorozhnoy platforme, pri udarah v avtostsepku. Dinamika ta keruvannya ruhom mehanichnih sistem, 87–95.
- Normyi dlya rascheta i proektirovaniya vagonov zheleznyih dorog MPS kolei 1520 mm (nesamohodnyih) (1996). Moscow, 319.
- Pravila razmescheniya i krepleniya gruzov v vagonah i konteynerah pri perevozkah ih po zheleznyim dorogam kolei 1520 mm stran-uchastnits SMGS. Part 1. Obschie polozheniya (2012). OSZhD, 681.
- Dyakonov, V. (2000). MATHCAD 8/2000. St. Petersburg, 592.
- Kiryanov, D. V. (2006). Mathcad 13. St. Petersburg, 608.
- Alyamovskiy, A. A. (2007). SolidWorks/COSMOSWorks 2006 – 2007. Inzhenernyiy analiz metodom konechnyih elementov. Moscow, 784.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2016 Alyona Lovskaya, Andrey Ryibin
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.