SOLVING THE ISSUE OF MODERNIZATION OF PRODUCTION EQUIPMENT USING CYBER-PHYSICAL MANUFACTURING CONTROL SYSTEMS
DOI:
https://doi.org/10.30837/ITSSI.2021.17.106Keywords:
Industry 4.0, Smart Manufacturing, cyber-physical production systems, additive cyber design, modernizationAbstract
Continuous improvement of the fleet of technological equipment, in the conditions of existing production, is a difficult task, the solution of which must take into account many parameters, such as mechanization, automation and application of new technologies within the concept of Industry 4.0. One of the effective methods of improving the technical and economic indicators and reliability of production is the modernization of existing technological equipment, which is based on the need to use modern methods of development and implementation of information technology, such as Industrial Internet of Things, cyber-physical production systems. The subject of this study is the testing of methods for developing additive cyber design for automation of complex industrial equipment. The goal of this article is to develop a cyber-physical production control system for the modernization of the DA2238B hydraulic press. To achieve this goal it is necessary to solve the following tasks: to analyze the technical characteristics and control system of the hydraulic press DA2238B; to carry out research of the scheme of hydraulic basic and, taking it into account, to choose sensors and executive mechanisms, and also operating modes; to develop the scheme of inclusion of the hydro equipment; to develop an automated control system based on a modern single-board computer and to develop an intuitive additive cyber-design of the operator interface; to conduct experimental research. Conclusions: as a result of research, a block diagram was developed and an automated control system based on LattePanda was implemented. Selected pressure and temperature sensors for control of pressing processes, which allowed to ensure accurate compliance with the requirements of the technological process. An automated operator's workplace has been developed, in which touch control based on additive cyber-design has been implemented. The developed control system provides: collection and analysis of production data on the basis of which it is possible to improve production technology and to provide forecasting of achievement "Lean Manufacturing".
References
Liashuk, O. L., Hevko, R. B., Dziura, V. O. (2019), The development and modernization of transport and technological mechanisms of machines and possession [Stvorennia ta modernizatsiia transportno-tekhnolohichnykh mekhanizmiv mashyn i obladannia]: Monograph, Ternopil, TNTU, 167 р. ISBN 978-617-7331-96-3
Gnidenko, A., Sobolevsky, V., Potriasaev, S., Sokolov, B. (2019), "Methodology and integrated modeling technologies for synthesis of cyber-physical production systems modernization programs and plans", IFAC-PapersOnLine, No. 52 (13), P. 642–647. DOI: https://doi.org/10.1016/j.ifacol.2019.11.305
Zhilevski, M., Mikhov, M. (2018), "Performance Improvement of a Type of Turning Machines", EJERS, European Journal of Engineer-ing Research and Science, Vol. 3, Issue 8, P. 44–49, DOI: https://doi.org/10.24018/ejers.2018.3.8.871
Platonov, V. V., Platonova, E. V., Maizel, I. G. (2017), "Modernization of numerically controlled machine tools on modular principles", Russian Engineering Research, No. 37, P. 140–143. DOI: https://doi.org/10.3103/S1068798X17020150
Mikhov, M., Zhilevski, M. (2021), "Study and Analysis of the Drive System for a Type of Milling Machines Aiming at Performance Improvement", New Ideas Concerning Science and Technology, Vol. 7, P. 31–43. DOI: https://doi.org/10.9734/bpi/nicst/v7/7254D
Radu, R., Marian, B., Alexandru, H., Bogdan, T. (2020), "Contributions to the modernization of fluid power field by integration of intelligent equipment", Instytut Techniki Górniczej KOMAG, Vol. 4, P. 39–47. DOI: https://doi.org/10.32056/KOMAG2020.4.5
Frolov, A. V. (2021), "The Experience of the Portal Machine Control System Modernizing for Automatic Arc Welding and Surfacing in a Shielded Gas", Current Problems and Ways of Industry Development: Equipment and Technologies, No. 7, P. 622–631. DOI: https://doi.org/10.1007/978-3-030-69421-0_66
Yakovenko, I., Permyakov, A., Naboka, O., Prihodko, O., Havryliuk, Y. (2020), "Parametric Optimization of Technological Layout of Modular Machine Tools", DSMIE 2020: Advances in Design, Simulation and Manufacturing III, Vol. 1, P. 85–93. DOI: https://doi.org/10.1007/978-3-030-50794-7_9
Wąsik, M., Lis, K., Lehrich, K., Mucha, Ł. (2018), "Model-Based Dynamic Structural Modification of Machine Tools", Shock and Vibration, Vol. 2018. DOI: https://doi.org/10.1155/2018/3469171
Nevliudov, I., Yevsieiev, V., Demska, N., Novoselov, S. (2020), "Development of a software module for operational dispatch control of production based on cyber-physical control systems", Innovative Technologies and Scientific Solutions for Industries, No. 4 (14), P. 155–168. DOI: https://doi.org/10.30837/ITSSI.2020.14.155
Osadchy, S., Demska, N., Oleksandrov, Y., Nevliudova, V. (2021), "Research of DIKW and 5C architectural models for creation of cyber-physical production systems within the concept of Industry 4.0", Innovative Technologies and Scientific Solutions for Industries, No. 1 (15), P. 132–140. DOI: https://doi.org/10.30837/ITSSI.2021.15.132
Zakoldaev, D. A., Shukalov, A. V., Zharinov, I. O., Zharinov, O. O. (2019), "Modernization stages of the Industry 3.0 company and projection route for the Industry 4.0 virtual factory", In IOP Conference Series: Materials Science and Engineering, Vol. 537, Issue 3, P. 538–541. DOI: https://doi.org/10.1088/1757-899X/537/3/032005
Pančík, J., Beneš, V. (2019), "IoT Challenge: Older Test Machines Modernization in an Automotive Plant", Smart Technology Trends in Industrial and Business Management, P. 85–100. DOI: https://doi.org/10.1007/978-3-319-76998-1_7
Yevsieiev, V. V. (2021), "Methods and models of cyber-physical process control in organizational and technical production facilities" ["Metody ta modeli kiber-fizychnoho keruvannia protsesamy v orhanizatsiino-tekhnichnykh vyrobnychykh obiektakh"]: avtoref. dis. ... Dr. Tech. Sciences, Kharkiv, NURE, 45 р., available at : https://openarchive.nure.ua/handle/document/16097
Nevliudov, I., Yevsieiev, V., Lyashenko, V., Ahmad, M. A. (2021), "GUI Elements and Windows Form Formalization Parameters and Events Method to Automate the Process of Additive Cyber-Design CPPS Development", Advances in Dynamical Systems and Applications, No. 16 (2), P. 441–455, available at : https://www.ripublication.com/adsa21/v16n2p04.pdf
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Our journal abides by the Creative Commons copyright rights and permissions for open access journals.
Authors who publish with this journal agree to the following terms:
Authors hold the copyright without restrictions and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License (CC BY-NC-SA 4.0) that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
Authors are able to enter into separate, additional contractual arrangements for the non-commercial and non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
Authors are permitted and encouraged to post their published work online (e.g., in institutional repositories or on their website) as it can lead to productive exchanges, as well as earlier and greater citation of published work.
