Experimental researches of the hybrid Rayleigh step bearing

Authors

DOI:

https://doi.org/10.15587/2313-8416.2016.64109

Keywords:

experimental researches, hybrid Rayleigh step bearing, experimental facility, sensors taring

Abstract

The experimental researches for hybrid Rayleigh step bearing at the different regimes of exploitation are investigated. Comparative analysis and the analysis of test data with theoretical calculations of the bearing static characteristics on the basis of thermohydrodynamic lubrication equalizations were carried out. The fundamental aspects of the test, concerning to hybrid bearing, the test procedure at the experimental facility, installed sensors taring, controlling and reading are determined

Author Biography

Татьяна Николаевна Сорокина, Nikolayev National Makarov University 9 Geroev Stalingrada ave., Nikolaev, Ukraine, 54025

Department of automatic 

References

Uchaev, P. N., Orlov, P. I. (Eds.) (1988). Osnovy konstruirovanija. Spravochno-metodicheskoe posobie. V 2-h kn. Kn. 2. Moscow: Mashinostroenie, 544.

Stachowiak, G. W., Batchelor, A. W. (2013). Engineering tribology. Elsevier Butterworth – Heinemann, 896.

Szeri, A. Z. (2011). Fluid Film Lubrication. Cambridge University Press, 564.

Voskresenskij, V. A., D'jakov, V. I. (1980). Raschet i proektirovanie opor skol'zhenija (zhidkostnaja smazka). Moscow: Mashinostroenie, 224.

Tokar', I. Ja. (1971). Proektirovanie i raschet opor trenija. Moscow: Mashinostroenie, 168.

Dowson, D., Taylor, C. M., Godet, M., Berthe, D. (Eds.) (1987). Fluid – film lubrication – Osborne Reynolds centenary. Elsevier Science Publishers B. V., 696.

Rowe, W. B. (1983). Hydrostatic and hybrid bearing design. Butterworths & Co. Ltd, 254.

Hlopenko, N. Ja., Koshkin, D. L. (2003). Jeksperimental'nye issledovanija opytnogo obrazca podshipnika Kingsberi pri torcovyh bienijah grebnja. Problemi tribologіi, 1, 57–61.

Etsion, I., Halperin, G., Brizmer, V., Kligerman, Y. (2004). Experimental Investigation of Laser Surface Textured Parallel Thrust Bearings. Tribology Letters, 17 (2), 295–300. doi: 10.1023/b:tril.0000032467.88800.59

Zhou, J., Blair, B., Argires, J., Pitsch, D. (2015). Experimental Performance Study of a High Speed Oil Lubricated Polymer Thrust Bearing. Lubricants, 3 (1), 3–13. doi: 10.3390/lubricants3010003

Mikula, A. M. (1988). Further Test Results of the Leading-Edge-Groove (LEG) Tilting Pad Thrust Bearing. Journal of Tribology, 110 (1), 174. doi: 10.1115/1.3261559

Wasilczuk, M. (2015). Friction and Lubrication of Large Tilting-Pad Thrust Bearings. Lubricants, 3 (2), 164–180. doi: 10.3390/lubricants3020164

Patil, A., Shinde, P. B., Chavan, S. P. (2012). Experimental studies of pressure distribution in tilting pad trust bearing with single continuous surface profiled sector shaped pads. International Journal of Applied Research in Mechanical Engineering (IJARME), 2 (2), 112–116.

Uilkok, U. (1970). Povyshenie dolgovechnosti ustanovok s podshipnikami kachenija blagodarja ispol'zovaniju kombinirovannogo podshipnika. Problemy trenija i smazki: Tr. Amer. o-va inzh.-meh. Moscow: Mir, 3, 34–42.

Hlopenko, N. Ja., Sorokina, T. N. (2013). Turbulentnaja neizotermicheskaja smazka stupenchatogo podpjatnika Rjeleja. Problemi tribologіi, 4, 40–45.

Hlopenko, N. Ja., Sorokina, T. N. (2015). Raznostnye shemy i tochnost' reshenija termogidrodinamicheskih uravnenij smazki podpjatnika Rjeleja. Problemi tribologіi, 2, 101–106.

Sorokina, T. N. (2015). Opisanie jeksperimental'noj ustanovki dlja issledovanija gidrostatodinamicheskogo podpjatnika s karmanami Rjeleja. Vіsnik NTU "HPІ". Serіja: Mehanіko-tehnologіchnі sistemi ta kompleksi, 36 (1145), 88–91.

Published

2016-03-27

Issue

Section

Technical Sciences