Justification of the limit blade wear oftillage tools

Authors

  • Сергій Іванович Бондарєв National University of Life and Environmental Sciences of Ukraine Heroyiv Oborony st., 11, Kyiv-03041, Ukraine, Ukraine

DOI:

https://doi.org/10.15587/2312-8372.2013.18359

Keywords:

tillage, hoes, tillage equipment, limiting wear of tools

Abstract

In modern ecological agricultural technologies primary attention is paid to the use of tillage equipment. It is necessary to follow the agrotechnical requirements in order to obtain good harvest. Rapid wear of tillage working bodies is a significant obstacle to the quality of soil cultivation. Therefore, the actual problem is to determine the limiting wear of tillage tools.

The results of experimental studies on determining the allowable wear of hoe blades are given. Multifactor field and laboratory experiments were conducted, which studied the influence of hoe blades wear on the uniform functioning of hoes in depths, quality of weeding, energy performance and defined physical and mechanical properties of weed roots. Based on them, it was found that wear from operating time of 6276 km of path length does not affect the quality and performance indicators, and operating time of about 100 km in selected field conditions can be considered as acceptable limiting wear of hoe blades.

Author Biography

Сергій Іванович Бондарєв, National University of Life and Environmental Sciences of Ukraine Heroyiv Oborony st., 11, Kyiv-03041, Ukraine

Professor

Department of Transport Technologies and Facilitiesin Agroindustrial Complex

References

  1. Амиржанов, Б. Долговечность робочих органов стерневых сеялок–культиваторов СЗС – 2,1 [Текст] : автореф. дис. на здобуття наук. ступеня канд. техн. наук по спец. 05.05.11 «Машини і засоби механізації сільсько-господарського виробництва» / Б. Амиржанов. – Москва, 1982. – 18 с.
  2. Ачкасов, К. А. Повышение долговечности лап сеялок-культиваторов СЗС–2.1 в условиях МНР [Текст] / К. А. Ачкасов, Ч. Нанжаа // Сб. науч. трудовв МИИСП. – Москва, 1987. – С. 61-65.
  3. Knight, A. C. Energy requirement to comminute compacted forages by slicing [Text] / A. C. Knight // J. Agric. Eng. Res. – 1981. – v 33. – № 4. – P. 263-271.
  4. Бахтін, П. У. Физико-механические и технологические свойства почв [Текст] / П. У. Бахтін // Справочник конструктора сельскохозяйственных машин. – Т. 1. – М.: Машиностроение, 1967. – С. 693-710.
  5. Mc. Randal, D.M., Mc. Nulty, P.B. Mechanical and physical properties of grasses. [Text] / D. M. Mc. Randal, P. B. Mc. Nulty // Trans. of ASAE. – 1980. – v 23. – № 4. – P. 816-821.
  6. Simon, J. Proc. Intern. Soil Tillage Research Org. ISTRO [Text] / J. Simon // 8th conf. University of Hohenheim. 1979. v 2. P. 211-217.
  7. Бондарєв, С. І. Обґрунтування оптимального міжремонтного наробітку стрілчастих лап культиваторних агрегатів [Text] : автореф. дис. на здобуття наук. ступеня канд. техн. наук : спец. 05.05.11 «Машини і засоби механізації сільськогосподарського виробництва» / С. Бондарєв. – Київ, 2007. – 20 с.
  8. O”Dogherty, M. J. A review of research on forage chopping [Text] / M. J. O”Dogherty // J. Agric. Eng. Res. – 1982. – v 27. – P. 267-289.
  9. Persson, S. Performance parameters for forage cutting devises [Text] / S. Persson // Paper of ASAE. – 1985. № 1554–85. – 28 p.
  10. Upadhyaya, S. K. Dynamics of soil–tool interaction [Text] / S. K. Upadhyaya, T. X. Ma, Y. M. Zxao and W. J Chancellor // A.S.A.E. Paper. № 85–1035. 1985. 48 р.
  11. Amirzhanov, B. (1982). Dolgovechnost' robochikh organov sternevykh seyalok–kul'tivatorov SZS – 2,1 : avtoref. dis. na zdobuttya nauk. stupenya kand. tekhn. nauk : spets. 05.05.11 «Mashini і zasobi mekhanіzatsії sіl's'ko-gospodars'kogo virobnitstva». Moscow, 18.
  12. Achkasov, K. A., Nanzhaa, Ch. (1987). Povyshenie dolgovechnosti lap seyalok-kul'tivatorov SZS–2.1 v usloviyakh MNR. Sb. nauch. trudovv MIISP. Moscow, 61-65.
  13. Knight A. C. (1981). Energy requirement to comminute compacted forages by slicing. J. Agric. Eng. Res, v 33, № 4, 263-271.
  14. Bakhtіn, P. U. (1967). Fiziko-mekhanicheskie i tekhnologicheskie svoystva. Spravochnik konstruktora sel'skokhozyaystvennykh mashin. T. 1. Moscow, 693-710.
  15. Mc. Randal, D. M., Mc. Nulty, P. B. (1980). Mechanical and physical properties of grasses. Trans. of ASAE, v 23, № 4, 816-821.
  16. Simon, J. (1979). Proc. Intern. Soil Tillage Research Org. ISTRO. 8th conf. University of Hohenheim, v 2, 211-217.
  17. Bondaryev, S. I. (2007). Obgruntuvannya optymal'noho mizhremontnoho narobitku strilchastykh lap kul'tyvatornykh ahrehativ : avtoref. dys. na zdobuttya nauk. stupenya kand. tekhn. nauk : spets. 05.05.11 «Mashyny i zasoby mekhanizatsiyi sil's'kohospodars'koho vyrobnytstva». Kiev, 20.
  18. O”Dogherty, M. J. (1982). A review of research on forage chopping. J. Agric. Eng. Res, v 27, 267-289.
  19. Persson, S. (1985). Performance parameters for forage cutting devises. Paper of ASAE, № 1554-85, 28.
  20. Upadhyaya, S. K., Ma,T. X., Zxao, Y. M. and Chancellor, W. J. (1985). Dynamics of soil-tool interaction. A.S.A.E. Paper, № 85-1035, 48.

Downloads

Published

2013-10-30

How to Cite

Бондарєв, С. І. (2013). Justification of the limit blade wear oftillage tools. Technology Audit and Production Reserves, 5(2(13), 8–10. https://doi.org/10.15587/2312-8372.2013.18359

Issue

Vol. 5 No. 2(13) (2013): Production reserves

Section

Production reserves

License

Copyright (c) 2016 Сергій Іванович Бондарєв

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.