Kinetics investigation of changing the oil film thickness depending on the material of friction pairs
DOI:
https://doi.org/10.15587/2312-8372.2015.55808Keywords:
oil, lubricating layer, viscosity, boundary layerAbstract
This article discusses the problems of dependence of changes of the effective viscosity of the ATF synthetic gear oil depending on the material of friction pairs. The aim of this article is to investigate the factors influencing the carrying capacity of the oil film. Tests were conducted on СМЦ-2 friction machine on the rollers, which are made of 40X steel (HRC=40) and ШХ-15 steel (HRC=60) at loads σmax=450, 570 and 680 MPa. Starting bulk oil temperature was 18 °C. The thickness of the lubricating layer was measured by the fall of a normal glow discharge. It was proved that a decrease in the hardness of contact surfaces leads to dominance in contact elastohydrodynamic factors of growth of the total thickness of the lubricating layer at the pushing, which is associated with a decrease in pressure-viscosity oil coefficient correlated growing influence of the dimensionless parameter of the material. The research results can be used in laboratories, manufacturers of lubricants in forming or improving their composition. From the kinetics analysis of formation of the lubricant layer at the contact surfaces of different hardness we can conclude that on the carrying capacity of the oil film in contact affect rheological characteristics of the oil and the dimensionless parameter of the material which depends on pressure-viscosity oil coefficient.References
- Garkunov, D. N. (2001). Tribotehnika (znos i beziznosnost'). Ed. 4. Moscow: MSHA, 616.
- Ahu Fahriye Acar, Fahrettin Ozturk, Mustafa Bayrak. (2010). Effects of variations in alloy content and machining parameters on the strength of the intermetallic bonding between diesel piston and ring carrier. Materials and technology, Vol. 44, № 6, 391–395.
- Petrusevich, A. I. (1963). Rol' gidrodinamicheskoi maslianoi plenki v stoikosti i dolgovechnosti poverhnostei detalei mashin. Vestnik mashinostroeniia, 1, 20–26.
- Grubin, A. N. (1949). Osnovy gidrodinamicheskoi teorii smazki tiazhelonagruzhennyh krivolineinyh poverhnostei. Book 33. Moscow: Mashgiz, 150.
- Gormakov, A. N. (2005). Issledovanie tribotehnicheskih harakteristik materialov. Tomsk: TPU, 21.
- Alehin, V. P. (1983). Fizika prochnosti i plastichnosti poverhnostnyh sloev materiala. Moscow: Nauka, 280.
- Demkin, N. B., Izmailov, V. V. (1975). Plastic contact under high normal pressure. Wear, Vol. 31, № 2, 391–402. doi:10.1016/0043-1648(75)90172-6
- In: McArdle, C. B. (1992). Side-Chain Liquid Crystal Polymers. Translated from English. Moscow: Mir, 567.
- Poltser, G., Maisener, F.; Translated from German: Ozerskiy, O. N.; In: Dobychin, M. N. (1984). Osnovy treniia i iznashivaniia. Moscow: Mashinostroenie, 264.
- Andreev, A. V. (1978). Peredacha treniem. Ed. 2. Moscow: Mashinostroenie, 176.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2016 Микола Федорович Дмитриченко, Олег Миколайович Білякович, Андрій Олексійович Глухонець, Костянтин Миколайович Міняйло
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
