Integrated technologies and physico-chemical properties of the power impulse of the pulse arc for defects in welding of aluminum alloys

Authors

DOI:

https://doi.org/10.15587/2313-8416.2017.118409

Keywords:

pulse arc welding, electrode, argon, aluminum, welding pool, films, arc impact

Abstract

The influence of the pulse arc welding force by a non-consumable electrode in the inert gas atmosphere (argon) on the weld metal during the process of welding of aluminum alloys is investigated. In particular, the issues of the power effect of pulse-arc welding on the degassing of the weld pool and the destruction of surface oxide films in the zone of influence of the welded seam when joining products made of aluminum alloy AMg6 by welding are considered

Author Biographies

Boris Sitnikov, National Technical University «Kharkiv Politechnic Institute» Kyrpychova str., 2, Kharkiv, Ukraine, 61002

PhD, Associate Professor

Department of Welding

Vyacheslav Marshuba, National Technical University «Kharkiv Politechnic Institute» Kyrpychova str., 2, Kharkiv, Ukraine, 61002

PhD, Associate Professor

Department of Welding

Natalia Miroshnichenko, National Technical University «Kharkiv Politechnic Institute» Kyrpychova str., 2, Kharkiv, Ukraine, 61002

PhD, Associate Professor

Department of Integrated Technologies, Processes and Devices

Lyudmila Solovey, National Technical University «Kharkiv Politechnic Institute» Kyrpychova str., 2, Kharkiv, Ukraine, 61002

Senior Lecturer

Department of Integrated Technologies, Processes and Devices

Irina Asieieva, National Technical University «Kharkiv Politechnic Institute» Kyrpychova str., 2, Kharkiv, Ukraine, 61002

Assistant

Department of General and Inorganic Chemistry

Stefan Shirokov, National Technical University «Kharkiv Politechnic Institute» Kyrpychova str., 2, Kharkiv, Ukraine, 61002

Department of Integrated Technologies, Processes and Devices

References

Skachkov, Y. N., Novikov, O. M., Mammon, M. D. (1973). The reasons for the appearance of oxide coatings in welded seams of AMg6 alloy. Jourmal Welding production, 4, 27–29.

Heifets, A. L., Goldfart, I. M. (1991). Influence of the parameters of current pulses on the destruction of oxide films and degassing of the bath during welding of thin-walled structures of AMg6 alloy. Jourmal Automatic welding, 11, 33–36.

Ishchenko, A. Y., Poklyatsky, A. G., Yavorskaya, M. P. (1989). Prevention of inclusions of oxide film in joints during argon-arc welding of aluminum alloys. Jourmal Automatic welding, 6, 38–41.

Mauro, H., Hirata, E. (1985). Forming of the weld bead in pulsed arc welding with non-consumable electrode in inert gases. Quarterly journal of the japan welding society, 3 (2), 17–24.

Ryazantsev, V. I., Slavin, G. A., Trokhinskaya, N. M. et. al. (1988). Features of the crystallization of a welding bath during welding with an arc of short-duration current pulses. Jourmal Welding production, 4, 39–41.

Novitsky, P. V. (1975). Electrotechnical measurements of non-electrical quantities. Leningrad: Energia, 576.

Mamonkin, I. G. (1966). Amplifying devices. Moscow: Communication, 400.

Tsykin, G. S. (1986). Electronic amplifiers. Moscow: Communication, 510.

Boykov, N. A., Zvezdin, P. S., Reznik, L. B. (1970). Measurement of pressures during fast processes. Moscow: Energia, 64.

Kolesnikov, P. N. (1971). Electrodynamic acceleration of plasma. Moscow: Atom-izdat, 372.

Published

2017-12-30

Issue

Section

Technical Sciences