Physical modeling of column distilling apparatus with dual-flow plates

Authors

  • Gennadiy Taranenko Volodymyr Dahl East Ukrainian National University Tsentralnyi ave., 59-a, Severodonetsk, Ukraine, 93400, Ukraine

DOI:

https://doi.org/10.15587/2313-8416.2018.131836

Keywords:

parametric series, hydrodynamic modeling, column, geometric characteristics, rectification, T parameter, bifurcation

Abstract

A hydrodynamic simulation of the operation of dual-flow plates for a parametric series of technological lines of column distilling apparatus with different capacity for raw alcohol installed in large-diameter columns is carried out. In the hydrodynamic simulation, experimental data are used in the study of dual-flow plates, installed in a column with a diameter of0.057 m. Experimental data are obtained on the model air-water system. The gas velocity calculated for the total cross section of the column is w=1.5, m/s

Author Biography

Gennadiy Taranenko, Volodymyr Dahl East Ukrainian National University Tsentralnyi ave., 59-a, Severodonetsk, Ukraine, 93400

PhD, Associate Professor

Department of Mechanical Engineering and Equipment industry

References

Stabnikov, V. N. (1969). Peregonka i rektifikacia etilovogo spirta [Distillation and rectification of ethyl alcohol]. Moscow: Pishhevaya promyshlennost, 456.

Stabnikov, V. N., Shtromilo, M. I. (1971). Proval’nye tarelki rektifikacionnyh apparatov i ikh primenenie na predpriyatiyah spirtovoy promyshlennosti [Dual-flow plates of rectifying devices and their use in alcohol industry enterprises]. Moscow: CNIITEHIpishcheprom, 20.

Rozen, A. M., Martyushin, E. I., Olevskyi, V. M. et. al.; Rozen, A. M. (Ed.) (1980). Masshtabnyi perehod v himicheskoy tehnologii: razrabotka himicheskih apparatov metodom gidrodinamicheskogo modelirovaniya [The scale transition in chemical technology: development of industrial apparatuses hydrodynamic simulation method]. Moscow: Chemistry, 320.

Taranenko, G. V. (2013). Gidravlichskie i massoobmennye harakteristiki tarelok proval’nogo tipa s pazlichnym diametrom otversty [Hydraulic and mass transfer characteristics of the dual-flow plates with different diameter holes]. Lugansk: Izd-vo VNU im. V. Dalya, 174.

Taranenko, G. V. (2015). Calculation of the lower operating limit dual-flow plates with different geometrical characteristics. ScienceRise, 3 (2 (8)), 67–73. doi: http://dx.doi.org/10.15587/2313-8416.2015.39196

Taranenko, G. (2017). Hydrodynamic modeling of the operating regimes of dual-flow plates installed in columns of various diameter. ScienceRise, 6 (35), 34–38. doi: http://dx.doi.org/10.15587/2313-8416.2017.103536

Kasatkin, A. G., Dytnersky, Yu. I., Umarov, S. U. (1958). K raschetu kolonn c proval’nymi tarelkami. Khimicheskaya promyshlennost, 3, 38–45.

Kasatkin, A. G. (1958). Osnovnye processy i apparaty himichiskoi tehnologii. Moscow: Chemistry, 752.

Sherwood, T. K., Shipley, G. H., Holloway, F. A. L. (1938). Flooding Velocities in Packed Columns. Industrial & Engineering Chemistry, 30 (7), 765–769. doi: http://dx.doi.org/10.1021/ie50343a008

Kochergin, N. A., Olevskiy, V. M., Dilman, V. V. (1960) Issledovanie raboty tarelok provalnogo tipa v usloviiah rektifikacii [The research of the operation of plates dual-flow of type under conditions of rectification]. Khimicheskaya promyshlennost, 7, 63–67.

Published

2018-05-22

Issue

Section

Technical Sciences