CREATION OF NEW LINES OF OXYGEN CENTRIFUGAL COMPRESSORS ON THE BASIS OF HIGHLY EFFECTIVE STEPS OF COMPRESSION

Authors

  • И. Г. Хисамеев ОАО «Казанькомпрессормаш», ул. Халитова, 1, г. Казань, РФ, 420029, Russian Federation
  • А. Г. Сафиуллин ЗАО «НИИтурбокомпрессор им. В.Б. Шнеппа», ул. Сибирский тракт, 40, г. Казань, РФ, 420029, Russian Federation
  • Я. З. Гузельбаев ЗАО «НИИтурбокомпрессор им. В.Б. Шнеппа», ул. Сибирский тракт, 40, г. Казань, РФ, 420029, Russian Federation
  • А. П. Харитонов ЗАО «НИИтурбокомпрессор им. В.Б. Шнеппа», ул. Сибирский тракт, 40, г. Казань, РФ, 420029, Russian Federation

DOI:

https://doi.org/10.18198/j.ind.gases.2008.0401

Keywords:

Oxygen, Centrifugal compressor, Step of compression, Driving wheel, Diffuser, Surge, Reliability, Automation, Safety

Abstract

Oxygen centrifugal compressors are applied to submission of oxygen under necessary pressure in a network of the enterprises. Energy consumption of compressors and also their reliability are essentially influence to general economic parameters of the enterprises realizing oxygen using technologies. It is informed on development of oxygen compressors of new generation on the basis of highly effective license flowing parts of firms «Dresser Clarks» (USA). They possess by a number of advantages in compared of compressors of old releases used now. For example, modern compressors on the IVth and IInd bases have parameters of specific capacity on 12-15 % below, than at compressor «KTK-12,5/35» used now. Compressor installations with compressors of new generation are completed by systems of automatic control and protection on the basis of industrial microprocessor controller LOGIX-5500 of firm «Allen-Bredley» (Rokwell Automation, USA). 

Author Biographies

И. Г. Хисамеев, ОАО «Казанькомпрессормаш», ул. Халитова, 1, г. Казань, РФ, 420029

I.G. Hisameev

А. Г. Сафиуллин, ЗАО «НИИтурбокомпрессор им. В.Б. Шнеппа», ул. Сибирский тракт, 40, г. Казань, РФ, 420029

A.G. Safiullin

Я. З. Гузельбаев, ЗАО «НИИтурбокомпрессор им. В.Б. Шнеппа», ул. Сибирский тракт, 40, г. Казань, РФ, 420029

Ya.Z. Guzelbaev

А. П. Харитонов, ЗАО «НИИтурбокомпрессор им. В.Б. Шнеппа», ул. Сибирский тракт, 40, г. Казань, РФ, 420029

A.P. Kharitonov

Downloads

Issue

No. 6 (2008): Технические газы

Section

PLANTS AND THE EQUIPMENT FOR MANUFACTURING OF AIR SEPARATION PRODUCTS AND OTHER INDUSTRIAL GASES

License

LICENSE AGREEMENT
After receiving an article for publication as required revision scientometric databases each author directs the license agreement on the assignment and transfer of the management of copyright. Signatures of the author (s) it is desirable to seal the personnel department of the institution where the author works (authors), or the seal of the Faculty.
Revision refers to the authors one layout for proofreading. Permissible only those fixes that result in compliance with the layout of the original text of the article. Significant changes are not permitted. Layout should be sent to the editorial office within days of receipt.