THE MAIN DIRECTIONS OF IMPROVEMENT OF INDUSTRY-ORIENTED CARBON DIOXIDE PISTON COMPRESSORS

Authors

  • А. В. Смирнов Sumskoe NPO by name M.V. Frunze», Gor`kiy Str., 58, Sumy, Ukraine, 40004, Ukraine
  • В. Н. Фесенко Sumskoe NPO by name M.V. Frunze», Gor`kiy Str., 58, Sumy, Ukraine, 40004, Ukraine
  • В. Ф. Оболоник Sumskoe NPO by name M.V. Frunze», Gor`kiy Str., 58, Sumy, Ukraine, 40004, Ukraine
  • В. В Найчук Sumskoe NPO by name M.V. Frunze», Gor`kiy Str., 58, Sumy, Ukraine, 40004, Ukraine
  • Ю. А. Рутковский Donbas state technical university, Lenin Str, 16, Alchevsk Lugansk region, Ukraine, 94204, Ukraine

DOI:

https://doi.org/10.18198/j.ind.gases.2013.0664

Keywords:

Piston compressor, Compressor unit, Resonant pressurizing, Valve, Compaction, Piston, Cylinder, Carbon dioxide

Abstract

In the industry piston compressors are widely used for carbon dioxide compression. Carbon dioxide, compressed to the pressure level of 15-20 MPa, is applied in carbamide manufacture. In 70-80th of last century for carbon dioxide compression over 40 installations on М16 opposite base were made by the Frunze Scientific Production Association, located in Sumy city. All the installations have been operating till now, but they need reconstruction or replacement. Some variants of modernization of the existing compressor installations for carbon dioxide compression as well as matters of introduction of self-lubricating materials for pistons and rods consolidation in designing of new compressors are considered.

Author Biographies

А. В. Смирнов, Sumskoe NPO by name M.V. Frunze», Gor`kiy Str., 58, Sumy, Ukraine, 40004

A.V. Smirnov

В. Н. Фесенко, Sumskoe NPO by name M.V. Frunze», Gor`kiy Str., 58, Sumy, Ukraine, 40004

V.N. Fesenko

В. Ф. Оболоник, Sumskoe NPO by name M.V. Frunze», Gor`kiy Str., 58, Sumy, Ukraine, 40004

V.F. Obolonik

В. В Найчук, Sumskoe NPO by name M.V. Frunze», Gor`kiy Str., 58, Sumy, Ukraine, 40004

V.V. Naychuk

Ю. А. Рутковский, Donbas state technical university, Lenin Str, 16, Alchevsk Lugansk region, Ukraine, 94204

Yu.A. Rutkovsky

References

Smirnov A.V., Grin` N.P., Shapovalov A.V. et al. (2009). Compressors for carbon dioxide: characteristics of manufactured models and directions of their perfection// Tekhnicheskie Gazy | Industrial Gases. ——№ 3. —С. 35-38. (Rus.).

Vidyakin Yu.A., Kondat`eva T.F., Petrova F.P. et al. (1972). Oscillations and vibrations in piston compressors. — Leningrad: Machinery construction. — 224 p. (Rus)

Frenkel` M.I. (1969). Piston compressors. — Moscow: Machinery construction. —742 p. (Rus)

Rutkovskiy Yu.A. (2010). Resonant wave processes in suction systems of piston compressors// Tekhnicheskie Gazy | Industrial Gases. — 2011. —№ 2. —С.23-32. (Rus)

Rutkovskiy Yu.A. (2008). Work of piston compressor at presence of oscillations of air pressure in suction pipe-line// Compressor and energetic machinery construction. — No. 3(13). — P. 83-92. (Rus)

Lavrenchenko G.K., Shvets S.G., Kopytin A.V. (2003). Use of resonance supercharge for increase the productivity of piston compressors// Tekhnicheskie Gazy | Industrial Gases. ——№ 4. — С. 9-15. (Rus.).

Smirnov A.V., Fesenko V.N., Korotenko S.V. et al. (2011). Directions of perfection of piston compressors for carbon dioxide and other gases// Tekhnicheskie Gazy | Industrial Gases. — No. 4. — P. 45-50. (Rus)

Smirnov A.V., Grin` N.P., Natalukha Yu.B. (2010). Development piston compressor block design 4VM10-55/71M1 for air separation plants medium pressure// Tekhnicheskie Gazy | Industrial Gases. — No. 6. — P. 31-35. (Rus.).

Downloads

Issue

No. 2 (2013): Технические газы

Section

PLANTS AND THE EQUIPMENT FOR MANUFACTURING OF AIR SEPARATION PRODUCTS AND OTHER INDUSTRIAL GASES

License

LICENSE AGREEMENT
After receiving an article for publication as required revision scientometric databases each author directs the license agreement on the assignment and transfer of the management of copyright. Signatures of the author (s) it is desirable to seal the personnel department of the institution where the author works (authors), or the seal of the Faculty.
Revision refers to the authors one layout for proofreading. Permissible only those fixes that result in compliance with the layout of the original text of the article. Significant changes are not permitted. Layout should be sent to the editorial office within days of receipt.