Исследование поверхности отклика, описывающей математическую модель влияния соотношения Al/Mg и температуры на жидкотекучесть Al-Mg сплава.
DOI:
https://doi.org/10.15587/2313-8416.2017.101923Słowa kluczowe:
ридж-анализ, субоптимальные значения, литье под низким давлением, Al-Mg сплав, жидкотекучесть, поверхность откликаAbstrakt
Методом ридж-анализа проведено исследование поверхности отклика, описывающей математическую модель влияния соотношения Al/Mg и температуры на жидкотекучесть Al-Mg сплава при литье под низким давлением. Показано, что на основе математической модели, построенной путем реализации центрального ортогонального композиционного плана (ОЦКП) второго порядка, могут быть найдены субоптимальные значения технологических режимов, обеспечивающих получение максимальных значений жидкотекучести Al-Mg сплава с учетом накладываемых на технологический процесс ограничений
Bibliografia
Demin, D. A. (2014). Quality Control at foundries technological aspects in selection of optimal strategies for technical reequipment. Bulletin of NTU “KhPI”. Series: New desicions of modern technologies, 7 (1050), 42–52.
Breslavskiy, D. V., Horoshilov, O. N., Ponomarenko, O. I. (2010). Upravlenie kachestvom nepreryvnolityh zagotovok. Visnyk DDMA, 3 (20), 41–46.
Horoshilov, O. N., Ponomarenko, O. I., Kipenskiy, A. V., Naniy, V. V., Kulichenko, V. V. (2012). Povyshenie kachestva nepreryvnolityh zagotovok iz mednyh splavov. Metallurgiya mashinostroeniya, 12, 29–31.
Lysenko, T. V., Stanovskiy, A. L. (2008). Adaptivnoe avtomatizirovannoe sinhroniziruyushchee proektirovanie sistemy "otlivka-peschanaya forma" NTI. Zbirnyk naukovyx pracz Odeskoyi nacionalnoyi morskoyi akademiyi, 13, 82–88.
Lysenko, T. V., Bondar', A. A. (2009). Metody samosinhronizacii dinamicheskih processov SAPR liteynogo proizvodstva KGV. Trudy Odesskogo politekhnicheskogo universiteta, 2 (32), 7–10.
Docenko, Yu. V., Seliverstov, V. Yu. (2011). The effects of aggregate technology to the properties of alloy castings АК7Ч with high iron content. Eastern-European Journal of Enterprise Technologies, 6 (5 (54)), 45–48. Available at: http://journals.uran.ua/eejet/article/view/2282
Docenko, Yu. V., Seliverstov, V. Yu., Sheydaev, K. V. (2012). Analiz ehffektivnosti kompleksnyh tekhnologicheskih resheniy po povysheniyu kachestva liteynyh alyuminievyh splavov s povyshennym soderzhaniem zheleza. New technologies and achievements in metallurgy and materials engineering. Czestochova, 211–216.
Docenko, Yu. V., Seliverstov, V. Yu. (2012). Features of solidification casting of aluminum alloys with increasing pressure and modification. Eastern-European Journal of Enterprise Technologies, 1 (5 (55)), 18–22. Available at: http://journals.uran.ua/eejet/article/view/3378
Docenko, Yu. V., Seliverstov, V. Yu. (2012). Zatverdevanie otlivok iz splava AK5M pri kompleksnom vozdeystvii na rasplav. Vestnik NTU "HPI". Seriya: Novye resheniya v sovremennyh tekhnologiyah, 1, 3–8.
Docenko, Yu. V., Seliverstov, V. Yu., Maciychuk, V. V., Malyh, S. V. (2012). Osobennosti ocenki ehffektivnosti polucheniya otlivok sposobom lit'ya pod vysokim davleniem. Vestnik NTU "HPI". Seriya: Novye resheniya v sovremennyh tekhnologiyah, 9, 21–29.
Rodionov, E. M. (1984). Tekhnologiya lit'ya pod nizkim davleniem. Moscow: NIImash, 56.
Chibichik, O. A. (2007). Analiz tekhnologicheskogo processa zalivki rotorov ehlektrodvigatelya i vozmozhnye puti ego usovershenstvovaniya. Eastern-European Journal of Enterprise Technologies, 6 (1 (30)), 55–60.
Akimov, O. V., Chibichik, O. A., Red'kina, A. V. (2013). Improvement of technical processes for producing cast rotor parts to increase performance characteristics of traction elecric drive. Problems of mechanical engineering, 16 (5), 7–12.
Demin, D. A. (2014). Mathematical description typification in the problems of synthesis of optimal controller of foundry technological parameters. Eastern-European Journal of Enterprise Technologies, 1 (4 (67)), 43–56. doi: 10.15587/1729-4061.2014.21203
Demin, D. A. (2011). Methodology of forming functional in the optimal control electric smelting. Technology audit and production reserves, 1 (1), 15–24. Available at: http://journals.uran.ua/tarp/article/view/4082
Mohanad, M. K., Kostyk, V., Domin, D., Kostyk, K. (2016). Modeling of the case depth and surface hardness of steel during ion nitriding. Eastern-European Journal of Enterprise Technologies, 2 (5 (80)), 45–49. doi: 10.15587/1729-4061.2016.65454
Demin, D. A. (2013). Adaptive modeling in problems of optimal control search termovremennoy cast iron. Eastern-European Journal of Enterprise Technologies, 6 (4 (66)), 31–37. Available at: http://journals.uran.ua/eejet/article/view/19453/17110
##submission.downloads##
Opublikowane
Numer
Dział
Licencja
Copyright (c) 2017 Olga Chibichik, Konstantin Sil’chenko, Dmytro Zemliachenko, Ivan Korchaka
Utwór dostępny jest na licencji Creative Commons Uznanie autorstwa 4.0 Międzynarodowe.
Our journal abides by the Creative Commons CC BY copyright rights and permissions for open access journals.
Authors, who are published in this journal, agree to the following conditions:
1. The authors reserve the right to authorship of the work and pass the first publication right of this work to the journal under the terms of a Creative Commons CC BY, which allows others to freely distribute the published research with the obligatory reference to the authors of the original work and the first publication of the work in this journal.
2. The authors have the right to conclude separate supplement agreements that relate to non-exclusive work distribution in the form in which it has been published by the journal (for example, to upload the work to the online storage of the journal or publish it as part of a monograph), provided that the reference to the first publication of the work in this journal is included.
