Analysis of cutting forces during grinding of titanium alloy and corrosion-resistant steel by diamond, electrocorundum and cubic borine nitrid wheels
DOI:
https://doi.org/10.15587/2706-5448.2021.235421Keywords:
titanium alloy VT8, cutting forces, technical strength, structural strength, reduction of energy consumption for grindingAbstract
The object of research is the process of circular and surface grinding of titanium alloy and corrosion-resistant steel, namely, the cutting forces arising from mechanical processing. One of the most problematic areas in work is the selection of the required grinding modes, material and grinding wheel grain size.
In the course of the experiment, we used samples of VT8 titanium alloy and 12Х18N9T steel, on which the grinding process was studied with wheels made of various materials (electrocorundum, cubic boron nitride (CBN), diamond). The values of the cutting forces Py and Pz were obtained in the latitude of permissible modes, which are most often used in circular and flat grinding, and can reach maximum values, respectively, Py=27 N, Pz=15.5 N. The data were obtained at a low wheel speed from electrocorundum, about 15 m/s and grain size 8. By reducing the grain size of the wheel, we get the effect of increasing the energy consumption of the grinding process, due to the increase in the values of the cutting forces. If we compare the cutting forces arising from grinding with different wheels, then the following can be noted. Compared to electrocorundum wheels, when using CBN wheels, the cutting forces are reduced by 20–25 %, and when grinding with diamond wheels (despite the high wear of the diamond wheel), the effect of cutting forces is reduced by 25–30 %. This is due to the fact that cutting conditions are the most favorable for diamond and CBN grains, which makes it possible to use more intense cutting conditions.
The results of the study allow predicting the performance of the grinding wheel, reducing the energy consumption of production, and also adjusting the processing mode of the part to obtain the necessary quality indicators of the surface layer and the geometric dimensions of the part.
References
- Lakhtin, Yu. M., Leonteva, V. P. (2011). Materialovedenie. Moscow: EKOLIT, 528.
- Kravchenko, B. A., Kravchenko, A. B. (2002). Fizicheskie aspekty teorii protsessa rezaniya metallov. Samara: Samar. gos. tekhn. un-t, 167.
- Kolachev, B. A., Egorova, YU. B., Belova, S. B. (2008). O svyazi temperatury (α+β)↔β perekhoda promyshlennykh titanovykh splavov s ikh khimicheskim sostavom. Metallovedenie i termicheskaya obrabotka metallov, 8 (638), 10–14.
- Lazoglu, I., Ehsan Layegh Khavidaki, S., Mamedov, A.; Davim, J. (Ed.) (2014). Mechanics of Titanium Machining. Machining of Titanium Alloys. Berlin, Heidelberg: Springer, 57–78. doi: http://doi.org/10.1007/978-3-662-43902-9_3
- Xing, H., Sun, J. Richter S., Schwedt, A. (Eds.) (2008). Deformation defects in a metastable β titanium alloy. EMC 2008 14th European Microscopy Congress 1–5 September 2008, Aachen, Germany. Berlin, Heidelberg: Springer, 675–676. doi: http://doi.org/10.1007/978-3-540-85226-1_338
- Ezugwu, E. O., Wang, Z. M. (1997). Titanium alloys and their machinability – a review. Journal of Materials Processing Technology, 68 (3), 262–274. doi: http://doi.org/10.1016/s0924-0136(96)00030-1
- De Mello, A., de Silva, R. B., Machado, Á. R., Gelamo, R. V., Diniz, A. E., de Oliveira, R. F. M. (2017). Surface Grinding of Ti-6Al-4V Alloy with SiC Abrasive Wheel at Various Cutting Conditions. Procedia Manufacturing, 10, 590–600. doi: http://doi.org/10.1016/j.promfg.2017.07.057
- Alimov, A. I. (2017). Sovershenstvovanie tekhnologii izgotovleniya kolets iz titanovogo splava VT8 putem opredeleniya ratsionalnykh rezhimov deformirovaniya. Moscow, 165.
- Turley, D. M. (1985). Factors affecting surface finish when grinding titanium and a titanium alloy (Ti-6Al-4V). Wear, 104 (4), 323–335. doi: http://doi.org/10.1016/0043-1648(85)90040-7
- Chen, Y. (2015). А study of the cutting forces andvibration characteristics in titaniummachining. Available at: http://unsworks.unsw.edu.au/fapi/datastream/unsworks:37124/SOURCE02?view=true
- Frolenkova, O. V. (2020). Zabezpechennia yakisnykh kharakterystyk napylenoho termobariernoho sharu elborovym shlifuvanniam. Odessa, 140.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Vladimir Lebedev, Tatiana Chumachenko, Alla Bespalova, Tatiana Nikolaeva, Yevhen Omelchenko
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
