Multiparameter controller usage for gas pumping unit control

Authors

  • Андрій Іванович Лагойда Ivano-Frankivsk National Technical University of Oil and Gas, Karpatska 15, Ivano-Frankivsk, Ukraine, 76019, Ukraine https://orcid.org/0000-0002-0862-7786

DOI:

https://doi.org/10.15587/2312-8372.2014.32580

Keywords:

centrifugal supercharger, controller, settings, transfer function, operation speed, design, surge, control

Abstract

Based on the experiment on a centrifugal supercharger Ц-6,3, which is included in anti-surge regulation of gas pumping units it is defined the productivity change of centrifugal supercharger and changes in the degree of increase in gas pressure, from which is derived the transfer function of a centrifugal supercharger of gas compressor unit.

The method of parameter determining of regulator setting through such component of Matlab software as Check Step Response Characteristics block is given. The technological process simulation is conducted with PID, PIDD2-, PIDD2D3-, PDD2-, and PDPD controllers based on the determined values in Matlab software and their optimal settings are determined.

During research of system using multi controllers it is found that operation speed of system increases in comparing with PID-controller at: PIDD2 controllers to 4,44 %, PIDD2D3 controllers to 22,67 %, PDD2 controllers to 89,33 %, and PDPD controllers to 98,22 %.

Author Biography

Андрій Іванович Лагойда, Ivano-Frankivsk National Technical University of Oil and Gas, Karpatska 15, Ivano-Frankivsk, Ukraine, 76019

Graduate student

Department of process automation and monitoring environmental

References

  1. Technological requirements for antypompazhnoho regulation centrifugal supercharger compressor units. (1999). К.: Ukrtransgas. № 399, 9.
  2. Kozakiewicz, V. (1974). Self-oscillations (surge) in the compressors. M.: Mashinostroenie, 264.
  3. Izmailov, R., Seleznev, K. (1995). Non-stationary processes in centrifugal compressors. Chemical and petroleum engineering, № 11, 20–24.
  4. Mamonov, O., Targonsky, V., Nishcheta, V. (2006). Introduction of energy saving technologies in the anti-surge control blowers. Media Review "Ukrtransgaz", № 1 (37), 6–7.
  5. Pismensky, I. (1987). Multi-frequency nonlinear oscillations in a gas turbine engine. M.: Mashinostroenie, 128.
  6. Fabri, I. (1967). Rotating stale inaxial flow compressors. Proceedings of the Conference Cambridge. Session 5: Unsteady flow effects, Paper 9. Internal Aerodynamics, Institution of Mechanical Engineers, 96–110.
  7. Sparks, C. R. (1983). On the Transient Interaction of Centrifugal Compressors and Their Piping Systems. Journal of Engineering for Power, Vol. 105, № 4, 891–901. doi:10.1115/1.3227498
  8. Smirnov, N., Sabanin, V., Repin, A. (2006). Robust multivariable controllers for objects with transport delay. Industrial process control and controllers, № 7, 82–86.
  9. Lagoyda, А., Blyaut, J., Lesiv, E., Sementsov, G. (2012). Analysis of the dynamic properties of a centrifugal supercharger compressor turbine drive as control object. Oil and Gas energy, № 2 (18), 72–85.
  10. Lagoyda, А., Sementsov, G. (2013). A method for increasing the speed of the automatic surge control pumping unit. Collection of scientific papers SWorld, № 9, 35–45.

Downloads

Published

2014-12-23

How to Cite

Лагойда, А. І. (2014). Multiparameter controller usage for gas pumping unit control. Technology Audit and Production Reserves, 6(4(20), 39–41. https://doi.org/10.15587/2312-8372.2014.32580

Issue

Vol. 6 No. 4(20) (2014): Scientific outcomes 2014

Section

Information technology and control systems

License

Copyright (c) 2016 Андрій Іванович Лагойда

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.