Reliability of stability control in view of production process

Authors

  • Валентина Ивановна Логанина Penza State University of Architecture and Construction, Street. Titov, 28, Penza, Russia, 440028, Russian Federation
  • Альбина Николаевна Круглова Penza State University of Architecture and Construction, Street. Titov, 28, Penza, Russia, 440028, Russian Federation
  • Ольга Александровна Давыдова Penza State University of Architecture and Construction, Street. Titov, 28, Penza, Russia, 440028, Russian Federation

DOI:

https://doi.org/10.15587/2312-8372.2013.18363

Keywords:

probability, control, reliability, type I error, statistics

Abstract

The data on the effect of measurement error on the probability of decision making on the products acceptance under statistical instability of the production process are given. It is shown that the objectivity of quality control depends on the accuracy of measuring devices, as well as the reproducibility of production process, characterized by the reproducibility indexes. This causes erroneous rejection of some effective items, the actual values of the controlled parameter of which lie in the tolerance zone.

By the example of production of ceramic brick three variants were shown, which are characterized by different values of reproducibility indexes. The probability of errors of the first and second kind was calculated, which indicate the probability of the situation when the controlled item is effective, but it will be erroneously considered to be defective, and when the controlled item is defective, but it can be wrongly considered to be effective. It is established that the probability of the error of the first and second kind increases as the production process reproducibility reduces.

Author Biographies

Валентина Ивановна Логанина, Penza State University of Architecture and Construction, Street. Titov, 28, Penza, Russia, 440028

Doctor of Technical Sciences, Professor

Doctor of Technical Sciences, Professor, Head of Department

Department of quality management and construction technologies

 

Альбина Николаевна Круглова, Penza State University of Architecture and Construction, Street. Titov, 28, Penza, Russia, 440028

Ph.D., associate professor

Department of "Mathematics and Mathematical Modeling"

Ольга Александровна Давыдова, Penza State University of Architecture and Construction, Street. Titov, 28, Penza, Russia, 440028

Candidate of Technical Sciences

Department of quality management and construction technologies

References

  1. Логанина, В. И. Организация статистического приемочного контроля качества строительных изделий и конструкций [Текст] / В. И. Логанина // Строительные материалы. – 2008. – № 8. – С. 98-99.
  2. Логанина, В. И. К вопросу о регулировании технологических процессов производства бетона [Текст] / В. И. Логанина // Известия высших учебных заведений. Строительство. – 2009. – № 3-4. – С. 42-45.
  3. Логанина, В. И. К вопросу о системе контроля качества на предприятиях стройиндустрии [Текст] / В. И. Логанина, Т. В. Учаева // Региональная архитектура и строительство. – 2010. – №1. – С. 31-36.
  4. Логанина, В. И. К вопросу о достоверности контроля при производстве бетона [Текст] / В. И. Логанина, А. Н. Круглова // Вестник Белгородского государственного технологического университета им. В. Г. Шухова. – 2011. – № 4. – С. 24-26.
  5. Bartlett, F. M. Precision of in-place concrete strenghts predicted using core strength correction factors obtained by weighted regression analysis [Text] / F. Michael Bartlett // Structural Safety. – 1997. – Vol. 19, Issue 4. – P. 397-410.
  6. Caspeele, R. Bayesian assessment of the characteristic concrete compressive strength using combined vague–informative priors [Text] / Robby Caspeele, Luc Taerwe // Construction and Building Materials. – March 2012. – Vol. 28, Issue 1. – P. 342-350.
  7. Zoubir Mehdi Sbartaï. Concrete properties evaluation by statistical fusion of NDT techniques [Text] /Zoubir Mehdi Sbartaï, Stéphane Laurens, Sidi Mohammed Elachachi, Cédric Payan // Construction and Building Materials. – December 2012. – Vol. 37. – P. 943-950.
  8. Song, P.S. Assessment of statistical variations in impact resistance of high-strength concrete and high-strength steel fiber-reinforced concrete [Text] / P.S. Song, J.C. Wu, S. Hwang, B.C. Sheu // Cement and Concrete Research. – February 2005. – Vol. 35, Issue 2. –P. 393-399.
  9. Fiore, A. On the dispersion of data collected by in situ diagnostic of the existing concrete [Text] / Andrea Fiore, Francesco Porco, Giuseppina Uva, Mauro Mezzina // Construction and Building Materials. – October 2013. – Vol. 47 – P. 208-217.
  10. ГОСТ 50.779.40-96. Статистические методы. Контрольные карты. Общее руководство и введение [Текст]. – М.: Изд-во стандартов, 1996.
  11. Серых, В. И. Многопараметрический контроль продукции: достоверность и затраты [Текст] / В. И. Серых, С. П. Порватов, В. И. Сединин // Методы менеджмента качества. – 2010. – №5. – С. 48-52.
  12. Левин, Б. Р. Теоретические основы статистической радиотехники [Текст] / Б. Р. Левин. – Кн. 1. – М.: Сов. радио,1965. – 752 с.
  13. Loganina, V. I. (2008). Orhanizatsiia statisticheskoho priemochnoho kontrolia kachestva stroitel'nykh izdelii i konstruktsii. Stroitel'nye materialy, № 8, 98-99.
  14. Loganina, V. I. (2009). K voprosu o rehulirovanii tekhnolohicheskikh protsessov proizvodstva betona. Izvestiia vysshikh uchebnykh zavedenii. Stroitel'stvo, № 3-4, 42-45.
  15. Loganina, V. I., Uchaeva, T. V. (2010). K voprosu o sisteme kontrolia kachestva na predpriiatiiakh stroiindustrii. Rehional'naia arkhitektura i stroitel'stvo, №1, 31-36.
  16. Loganina, V. I., Kruglova, A. N. (2011). K voprosu o dostovernosti kontrolia pri proizvodstve betona. Vestnik Belhorodskoho hosudarstvennoho tekhnolohicheskoho universiteta im. V. H. Shukhova, № 4, 24-26.
  17. Bartlett, F. M. (1997). Precision of in-place concrete strenghts predicted using core strength correction factors obtained by weighted regression analysis. Structural Safety, Volume 19, Issue 4, 397-410.
  18. Caspeele, R., Taerwe, L. (March 2012). Bayesian assessment of the characteristic concrete compressive strength using combined vague–informative priors. Construction and Building Materials, Volume 28, Issue 1, 342-350.
  19. Zoubir Mehdi Sbartaï, Stéphane Laurens, Sidi Mohammed Elachachi, Cédric Payan. (December 2012). Concrete properties evaluation by statistical fusion of NDT techniques. Construction and Building Materials, Volume 37, 943-950.
  20. Song, P. S., Wu, J. C., Hwang, S., Sheu, B. C. (February 2005). Assessment of statistical variations in impact resistance of high-strength concrete and high-strength steel fiber-reinforced concrete. Cement and Concrete Research, Volume 35, Issue 2, 393-399.
  21. Fiore, A., Porco, F., Uva, G., Mezzina, M. (October 2013). On the dispersion of data collected by in situ diagnostic of the existing concrete. Construction and Building Materials, Volume 47, 208-217.
  22. GOST 50.779.40-96. Statisticheskie metody. Kontrol'nye karty. Obshchee rukovodstvo i vvedenie. (1996). M.: Izd-vo standartov.
  23. Serykh, V. I., Porvatov, S. P., Sedinin, V. I. (2010). Mnohoparametricheskii kontrol' produktsii: dostovernost' i zatraty. Metody menedzhmenta kachestva, №5, 48-52.
  24. Levin, B. R. (1965). Teoreticheskie osnovy statisticheskoi radiotekhniki. Book 1. M.:Sov.radio, 752.

Downloads

Published

2013-10-30

How to Cite

Логанина, В. И., Круглова, А. Н., & Давыдова, О. А. (2013). Reliability of stability control in view of production process. Technology Audit and Production Reserves, 5(2(13), 22–24. https://doi.org/10.15587/2312-8372.2013.18363

Issue

Vol. 5 No. 2(13) (2013): Production reserves

Section

Production reserves

License

Copyright (c) 2016 Валентина Ивановна Логанина, Альбина Николаевна Круглова, Ольга Александровна Давыдова

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.