Circuit design of buck-voltage converter with digital control system

Authors

DOI:

https://doi.org/10.15587/2706-5448.2020.202024

Keywords:

buck-converter, signal control, galvanic isolation in power equipment, digital control.

Abstract

The objects of research are processes in electrical scheme and enormous digital control systems in converter. One of the most problematic things is transfer and energy change in converter for current and voltage in order to reach certain value of digital range with a minimal percentage of error.

This work explores buck-voltage converter with digital control system. An enormous considered procedure of projecting electrical scheme. There was described electrical scheme with a control system, which, thanks to the digital system, provides dates with more accuracy in the output of converter, among them: assignment of certain digital range of output voltage and system’s impact on working scheme.

During the research there was used selection of hardware features and software tools, accepting peripheral devices, which let quickly and simply set up microcontroller for certain operating mode and to realize controlling system for buck converter in a programmatic manner.

There was analyzed procedure of solving and choosing of the certain parts of electrical scheme, where was used to construct:

– microcontroller for receiving, processing and issuance of information in electrical scheme;

– driver operating and analog-to-digital conversion;

– driver for control of the switches – basically transistors;

– components of the buck-converter circuit.

There is description and schematic choice of the certain parts of the scheme. There was included switch, capacitor and diode for buck converter; certain range of the frequency and voltage for microcontroller; control of the power keys of the circuit with the corresponding operating parameters for driver.

There was received a system, which in prospect will become a basis to step down voltage value to the certain level. This is because defined method has a set of features, particularly digital regulation system with a discrete step and analog-to-digital converter in the capacity of feedback. Therewith provides possibility for receiving more accuracy value. In comparison with analogic buck converters, this converter has voltage parameter with fractional error.

Author Biography

Yehor Zheliazkov, National Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute», 37, Peremohy ave., Kyiv, Ukraine, 03056

Department of Electronic Devices and Systems

References

  1. Dymko, S. S., Teriaiev, V. I. (2020). Pidvyshchuiuchyi peretvoriuvach napruhy z tsyfrovoiu systemoiu keruvannia. Suchasni problemy elektroenerhotekhniky ta avtomatyky, 427–431.
  2. Zhou, X., He, Q. (2015). Modeling and Simulation of Buck-Boost Converter with Voltage Feedback Control. MATEC Web of Conferences, 31, 10006. doi: http://doi.org/10.1051/matecconf/20153110006
  3. Rashid, H. (Ed.) (2001). Power Electronics Handbook. Academic Press series in engineering, 254.
  4. Schell, D., Kastorena, Zh. (2007). Razrabotka ponizhayushchego preobrazovatelya bez sekretov. Komponenty i tekhnologii, 4, 106–109.
  5. PIC16F877A Microcontroller Introduction and Features. Available at: https://microcontrollerslab.com/pic16f877a-introduction-features/
  6. PWM using Pic Microcontroller with Examples. Available at: https://microcontrollerslab.com/pwm-using-pic16f877a-microcontroller/
  7. How to use MOSFET/IGBT DRIVER IR2184S. Available at: https://www.hobbytronics.co.uk/ir2184-mosfet-driver
  8. IR2184 High and Low Side MOSFET Driver. Available at: https://www.hobbytronics.co.uk/ir2184-mosfet-driver
  9. Spravochnik po elektronnym komponentam IR2184, IR21844 «Draiver klyuchei nizhnego i verhnego urovnei». Available at: http://www.gaw.ru/html.cgi/txt/ic/IR/control/drivers2/2/IR2184_844.htm
  10. Buck converter using pic microcontroller and IR2110. Available at: https://microcontrollerslab.com/buck-converter-using-pic-microcontroller-ir2110/

Downloads

Published

2020-03-05

How to Cite

Zheliazkov, Y. (2020). Circuit design of buck-voltage converter with digital control system. Technology Audit and Production Reserves, 2(1(52), 46–50. https://doi.org/10.15587/2706-5448.2020.202024

Issue

Vol. 2 No. 1(52) (2020): Industrial and technology systems

Section

Reports on research projects

License

Copyright (c) 2020 Yehor Zheliazkov

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.