Contact сharacter of work surface of cylindrical gears tooth with conchoidal engagement line depending

Authors

  • Светлана Юрьевна Сапронова Volodymyr Dahl East Ukrainian National University, bl. Molodizny, 20a, Luhansk, Ukraine, 91034, Ukraine
  • Александр Анатольевич Муховатый Volodymyr Dahl East Ukrainian National University, bl. Molodizny, 20a, Luhansk, Ukraine, 91034, Ukraine
  • Виктор Петрович Ткаченко Volodymyr Dahl East Ukrainian National University, bl. Molodizny, 20a, Luhansk, Ukraine, 91034, Ukraine

DOI:

https://doi.org/10.15587/2312-8372.2014.21210

Keywords:

cylindrical gear, surface, profile, contour, gearing, contact, conchoidal engagement line

Abstract

Load capacity of gears depends on the character of work surfaces contact: two convex contact or contact the convex and concave surfaces. Therefore, the actual solution to the problem is to determine the geometrical parameters of the tooth, providing the most rational given character of their work surfaces contact. This fully applies to the gears with conchoidal engagement line for which this problem has not been studied yet.

Тhere have been gotten the conditions defining the character of tooth work surface contact with conchoidal engagement line depending on the geometrical parameters of the original contour. There have been defined the original contours parameters providing convex-concave tooth contact and the contact of two convex teeth in the engaging meshing pairs. There have been given recommendations as for defining the parameters of the original contour depending on the character of contact in cylindrical spur gear work surfaces.

Author Biographies

Светлана Юрьевна Сапронова, Volodymyr Dahl East Ukrainian National University, bl. Molodizny, 20a, Luhansk, Ukraine, 91034

Doctor of Technical Sciences, docent, Professor of the Department internal combustion engines and Mechanical Engineering

Александр Анатольевич Муховатый, Volodymyr Dahl East Ukrainian National University, bl. Molodizny, 20a, Luhansk, Ukraine, 91034

Candidate of Technical Sciences, senior Lecturer of the Department internal combustion engines and Mechanical Engineering

Виктор Петрович Ткаченко, Volodymyr Dahl East Ukrainian National University, bl. Molodizny, 20a, Luhansk, Ukraine, 91034

Doctor of Technical Sciences, Professor, Professor of the Department avtoniki and Transport Management

References

  1. Шабанов, И. Р. О зубчатой передаче с конхоидальной линей зацепления [Текст] / И. Р. Шабанов // Надежность и качество зубчатих передач. НИИ ИНФОРМТЯЖМАШ. 18-67-106. − 1967. – С. 1-8.
  2. Шабанов, И. Р. Зубчатая передача, состоящая из цилиндрических зубчатых колес с конхоидальной линией зацепления и ее элементы [Текст]/ И. Р. Шабанов // Труды УСХИ. Том XII. − 1966. − Вып.16. − С. 20-28.
  3. Носко, П. Л. Сравнительный анализ критерия контактной прочности неэвольвентных цилиндрических зубчатых передач [Текст] / П. Л. Носко, В. П. Шишов, А. А. Муховатый // Вісник НТУ «ХПІ». − Харків: НТУ «ХПІ», 2012. − № 35. − С. 119-124.
  4. Шишов, В. П. Теоретические основы синтеза передач зацеплением: монография [Текст] / В. П. Шишов, П. Л. Носко, П. В. Филь. − Луганськ: Bид-во СНУ ім. В. Даля, 2006. − 408 с.
  5. Boshansky, M. Volba geometrickych parametrov konvexno-konkaveho ozubenia z hladiska povrchoveho poskodenia bonu zuba [Text]/ M. Boshansky. − SjF STU, Bratislava, 1997. – 104 p.
  6. Veres, M. Teoria celneho rovinneho ozubenia [Text]/ M. Veres, M. Boshansky. – STK Bratislava, 1999. – 112 p.
  7. Veres, M. Theory of Convexo-concave and plane cylindrical gearing [Text]/ M. Veres, M. Boshansky, J. Gachis. – Slovak university of technology, Bratislava, 2006. – 180 p.
  8. Litvin, F. Gear Geometry and Applied Theory [Text]/ F. Litvin, A. Fuentes. – Ed. 2. – Cambridge University, 2004. – 125 p.
  9. Boshansky, M. Posudenie vhodnosti pouzitia Sortveru v pevnostney analize ozubenych kolies metodom MKP [Text] / M. Boshansky, J. Medzihradsky. – Acta Mechanica Slovaka, Kosice, 2007. – P. 45-53.
  10. Шишов, В. П. Критерии оценки работоспособности передач зацеплением [Текст]/ В. П. Шишов, Д. А. Панкратов, А. А. Муховатый // Вісник НТУ «ХПІ». − Харків: НТУ «ХПІ», 2001. − № 12. − С. 33-40.
  11. Shabanov, I. R. (1967). Gearing of conchoidal cohesion line. Safety and quality of gearings, NII INFORMTIAZMASH 18-67-106, 1-8.
  12. Shabanov, I. R. (1966). Gearing consisting of cylindrical toothed wheels with conchoidal cohesion line and its elements. Тrudy USHI, Том XII, 16, 20-28.
  13. Nosko, P. L., Shishov, V. P, Мukhovatiy, А. А. (2012). Comparative analysis of durability contact criteria in non-evolvent cylindrical gearings. Vіsnik NTU «KHPI»,Kharkiv, NTU «HPI», № 35, 119-124.
  14. Shishov, V. P., Nosko, P. L., Fil, P. V. (2006). Teoreticheskie osnovy sinteza peredach zatsepleniem: monograph. Vid-vo SNU im. V. Dal, Luhansk, 408.
  15. Boshansky, M. (1997). Volba geometrickych parametrov konvexno-konkaveho ozubenia z hladiska povrchoveho poskodenia bonu zuba. SjF STU, Bratislava, 104.
  16. Veres, M., Boshansky, M. (1999). Teoria celneho rovinneho ozubenia. STK Bratislava, 112.
  17. Veres, M., Boshansky, M., Gachis, J. (2006). Theory of Convexo-concave and plane cylindrical gearing. Slovak university of technology, Bratislava, 180.
  18. Litvin, F., Fuentes, A. (2004). Gear Geometry and Applied Theory. Second Edition, Cambridge University, 125.
  19. Boshansky, M., Medzihradsky, J. (2007). Posudenie vhodnosti pouzitia Sortveru v pevnostney analize ozubenych kolies metodom MKP. Acta Mechanica Slovaka, Kosice, 45-53.
  20. Shishov, V. P., Pankratov, D. A., Мukhovatiy, А. А. (2001). Kriterii ocenki rabotosposobnosti peredach zatcepleniem. Vіsnik NTU «KHPI»,Kharkiv, NTU «HPI», № 12, 33-40.

Downloads

Published

2014-02-06

How to Cite

Сапронова, С. Ю., Муховатый, А. А., & Ткаченко, В. П. (2014). Contact сharacter of work surface of cylindrical gears tooth with conchoidal engagement line depending. Technology Audit and Production Reserves, 1(1(15), 14–17. https://doi.org/10.15587/2312-8372.2014.21210

Issue

Vol. 1 No. 1(15) (2014): Technology audit

Section

Technology audit

License

Copyright (c) 2016 Светлана Юрьевна Сапронова, Александр Анатольевич Муховатый, Виктор Петрович Ткаченко

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.