Structural and metrological aspects of piston-type gas-measuring units (gas piston prover)
DOI:
https://doi.org/10.15587/2312-8372.2014.21688Keywords:
gear transmission, accuracy, kinematic schemeAbstract
The article describes development and combination of a drive unit of primary standard of gas volume and volume flow units at the pressure of 1,6 MPa, which is a synthesis of power-speed reduction gear transmissions. The optimal design of a drive unit is application of a complex of gear reducers, where a reducer with cylindrical gear, with variable stepped transmission ratio, with reverse gear is used for high-speed transmission, while for power transmission a reducer with bevel gear, with hypoid gear, with involute profile of helical teeth is used. Oriented values of transmission ratios of gear drives are calculated on basis of the input data, i.e. a number of values of gas volume flow, selected for calibration (certification) of gas meters within the range from 4 m3/hour to 200 m3/hour. The general kinematic scheme of primary standard is worked out, the metrological aspect is considered and complex indices of kinematic accuracy of applied reducers of the drive unit are calculated in the article.References
- ДСТУ EN 12261:2006. Лічильники газу турбінні. Загальні технічні умови (EN 12261:2002, IDT) [Текст]. – Київ: Держспоживстандарт України. – 39 с.
- ISO 17089-1:2010. Ultrasonic meters for gas [Text]/ Part 1: Meters for custody transfer and allocation measurement. – Geneva, 2010. – 108 p.
- Петришин, І. С. Впливові фактори конструктивних особливостей поршневих еталонних витратомірних установок, що працюють при високому тиску [Текст]/ І. С. Петришин та ін. // Метрологія та прилади. – 2013. – №5 – С. 6-16.
- Кузьмин, А. В. Справочник по расчетам механизмов подъемно-транспортных машин [Текст]/ А. В. Кузьмин, Ф. Л. Марон. – Минск: Высшая школа, 1983. – 350 с.
- Башта, Т. М. Гидропривод и гидропневмоавтоматика [Текст]. – Москва: Машиностроение, 1972. – 320 с.
- Скойбеда, А. Т. Детали машин и основы конструирования [Текст]: учеб. / А. Т. Скойбеда, А. В. Кузьмин. – Мн.: Вышэйшая школа, 2000. – 584 с.
- ГОСТ 1643-81. Основные нормы взаимозаменяемости. Передачи зубчатые цилиндрические. Допуски [Текст]. – М.: Изд-во стандартов, 1981. – 45 с.
- ГОСТ 1758-81. Основные нормы взаимозаменяемости. Передачи зубчатые конические и гипоидные. Допуски [Текст]. – М.: Государственный комитет СССР по стандартам, 1981. – 43 с.
- ГОСТ Р 52924-2008. Автомобильные транспортные средства. Шарниры равных угловых скоростей. Общие технические требования и методы испытаний [Текст]. – М.: Стандартинформ, 2008. – 11с.
- Михайловський, Е. В. Устройство автомобиля. [Текст]/ Е. В. Михайловський, К. Б. Серебряков, Е. Я. Тур. – 4-е изд. – М.: Машиностроение, 1981. – 342 с.
- DSTU EN 12261:2006. Lichylnyky hazu turbinni. Zahalni tekhnichni umovy (EN 12261:2002, IDT). Kyiv: Derzhspozhyvstandart Ukrainy, 39.
- ISO 17089-1:2010. Ultrasonic meters for gas. (2010). Part 1: Meters for custody transfer and allocation measurement. Geneva, 108.
- Petryshyn, I. S. and others. (2013). Vplyvovi faktory konstruktyvnykh osoblyvostei porshnevykh etalonnykh vytratomirnykh ustanovok, shcho pratsiut pry vysokomu tysku. Metrolohiia ta prylady, №5, 6-16.
- Kuzmyn, A. V., Maron, F. L. (1983). Spravochnyk po raschetam mekhanyzmov podemno-transportnykh mashyn. Mynsk: Vysshaia shkola, 350.
- Bashta, T. M. (1972). Hydropryvod y hydropnevmoavtomatyka. Moskva: Mashynostroenye, 320.
- Skoibeda, A. T., Kuzmyn, A. V. and others. (2000). Detaly mashyn y osnovы konstruyrovanyia. Mn.: Vysheishaia shkola, 584.
- HOST 1643-81. (1981). Osnovnye normy vzaymozamenaemosty. Peredachy zubchate tsylyndrycheskye. Dopusky. M.: Yzdatelstvo standartov, 45.
- HOST 1758-81. (1981). Osnovnye normy vzaymozameniaemosty. Peredachy zubchatye konycheskye y hypoydnye. Dopusky. M.: Hosudarstvennыi komytet SSSR po standartam, 43.
- HOST R 52924-2008. (2008). Avtomobylnye transportnye sredstva. Sharnyry ravnykh uhlovykh skorostei. Obshchye tekhnycheskye trebovanyia y metody yspytanyi. M.: Standartynform, 11.
- Mykhailovskyi, E. V., Serebriakov, K. B., Tur, E. Ya. (1981). Ustroistvo avtomobylia. Ed. 4-e. M.: Mashynostroenye, 342.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2016 Олександр Анатолійович Бас
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.