Study of the dynamics of stress formation in glass during a thermal hardening
DOI:
https://doi.org/10.15587/2706-5448.2020.220535Keywords:
sheet float glass, thermal hardening, stress diagram, bending strength.Abstract
The object of research is the ultimate bending strength of float glass sheet 4 mm thick. The paper confirms that the main factor affecting the increase in glass strength is the dynamics of stress formation in the surface and inner layers of glass. Rapid cooling of float glass with an air flow for 8–10 s at a rate of 25 °C/s leads to the appearance in the glass of an average temperature difference in the surface zone of 30 °C/mm. It was found that during thermal hardening at temperatures exceeding the glass transition temperature limit, there is an abrupt increase in the glass bending strength. A comparative analysis of the results of measuring the bending strength of glass for float glass and heat-strengthened glass indicates that this indicator is significantly improved. The statistical analysis of the results shows that the scatter of the values of the bending strength of annealed glass falls within the range of 30–50 MPa, and the most probable value is 40 MPa. At the same time, the spread in the values of the bending strength of thermally hardened glass is in the range of 100–160 MPa and is 135 MPa. The work proved that thermal hardening of float glass sheets increases its flexural strength by about 3.5 times. The peculiarities of the change in the type of the hardening stress diagram over time have also been studied: thermal hardening causes a more gentle course of the residual stress curve compared to hardening. In this case, the coordinate of the critical tensile stress σcrit can be located on the lower surface of the glass, which will make it possible to fracture at lower loads compared to quenching, but the fracture mechanism will be identical as for annealed glass. In this case, the destruction mechanism will be approximately the same as in the case of annealed glass, but its actual strength will be 2–3 times higher.
References
- Pisano, G., Carfagni, G. R. (2017). A micromechanical derivation of the macroscopic strength statistics for pristine or corroded/abraded float glass. Journal of the European Ceramic Society, 37 (13), 4197–4206. doi: http://doi.org/10.1016/j.jeurceramsoc.2017.04.046
- Koike, A., Akiba, S., Sakagami, T., Hayashi, K., Ito, S. (2012). Difference of cracking behavior due to Vickers indentation between physically and chemically tempered glasses. Journal of Non-Crystalline Solids, 358 (24), 3438–3444. doi: http://doi.org/10.1016/j.jnoncrysol.2012.02.020
- Li, X., Jiang, L., Wang, Y., Mohagheghian, I., Dear, J. P., Li, L., Yan, Y. (2017). Correlation between K+-Na+ diffusion coefficient and flexural strength of chemically tempered aluminosilicate glass. Journal of Non-Crystalline Solids, 471, 72–81. doi: http://doi.org/10.1016/j.jnoncrysol.2017.05.011
- Guerette, M., Ackerson, M. R., Thomas, J., Yuan, F., Bruce Watson, E., Walker, D., Huang, L. (2015). Structure and Properties of Silica Glass Densified in Cold Compression and Hot Compression. Scientific Reports, 5 (1). doi: http://doi.org/10.1038/srep15343
- Nyounguè, A., Bouzid, S., Dossou, E., Azari, Z. (2016). Fracture characterisation of float glass under static and dynamic loading. Journal of Asian Ceramic Societies, 4 (4), 371–380. doi: http://doi.org/10.1016/j.jascer.2016.07.004
- Uaiett, O., Diu-Khiuz, D.; Liubova, B. Iu. (Ed.) (1979). Metally, keramiki, polimery Vvedenie k izucheniiu i struktury i svoistv tekhnicheskikh materialov. Moscow: Atomizdat, 580.
- Sundberg, P., Grund Bäck, L., Orman, R., Booth, J., Karlsson, S. (2019). Simultaneous chemical vapor deposition and thermal strengthening of glass. Thin Solid Films, 669, 487–493. doi: http://doi.org/10.1016/j.tsf.2018.11.028
- Sheth, N., Hahn, S. H., Ngo, D., Howzen, A., Bermejo, R., van Duin, A. C. T. et. al. (2020). Influence of acid leaching surface treatment on indentation cracking of soda lime silicate glass. Journal of Non-Crystalline Solids, 543. doi: http://doi.org/10.1016/j.jnoncrysol.2020.120144
- Wang, Z., Guan, T., Ren, T., Wang, H., Suo, T., Li, Y. et. al. (2020). Effect of normal scratch load and HF etching on the mechanical behavior of annealed and chemically strengthened aluminosilicate glass. Ceramics International, 46 (4), 4813–4823. doi: http://doi.org/10.1016/j.ceramint.2019.10.214
- Ballarini, R., Pisano, G., Royer Carfagni, G. (2016). New calibration of partial material factors for the structural design of float glass. Comparison of bounded and unbounded statistics for glass strength. Construction and Building Materials, 121, 69–80. doi: http://doi.org/10.1016/j.conbuildmat.2016.05.136
- Plemiannikov, M. M., Krupa, A. A. (2000). Khimiia ta teplofizyka skla. Kyiv: NTUU «KPI», 560.
- Chumak, V. L., Ivanov, S. V., Maksymiuk, M. R. (2012). Osnovy naukovykh doslidzhen. Kyiv: NAU-druk, 360.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2020 Vladyslav Shcherban, Nataliya Zhdanyuk, Mykola Plemyannikov
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
