Development of new welding consumables for wet underwater welding of high-alloy corrosion-resistant steel
DOI:
https://doi.org/10.15587/2312-8372.2015.51448Keywords:
flux-cored wire, steel Ch18Ni10Ti, covered electrode, nuclear power plants, gas saturation, wet weldingAbstract
The paper describes the technology for mechanized wet underwater welding of high-alloy corrosion-resistant steel. The main purpose of the research is development of the pioneering self-shielding flux-cored wire for wet underwater welding. Quantity and quality characteristics were determined by using the mathematical experimental design method. Quantity and quality welding-technological characteristics, such as gas saturation of the weld metal, stability of the arc burning process in water environment, and optimal composition of slag-forming components of the flux-cored wire charge, were specified. Application of the experimental self-shielding wire for mechanized wet underwater welding of high-alloy corrosion-resistant steel will make it possible to increase productivity and improve quality of underwater welding-repair operations, and receive an economic effect due to reduction of downtime in production cycle of an object being repaired. Application of this technology will allow a partial or even complete absence of participation of humans in the welding process performed under extreme conditions in radioactive environment (in case of nuclear power plants) and in welding in deep waters. The research results can be used for welding-repair operations at nuclear power plants, ship-repair and ship-raising operations, and at hydraulic facilities. The proposed innovation technology makes it possible to fully replace the wet underwater covered-electrode welding technology.References
- Hancock, R. (2003). Underwater nuclear. Welding Journal, 9, 48–49.
- O`Sullivan, J. E. (1988). Wet underwater weld repair of Susquehanna unit 1 steam dryer. Welding journal, 6, 19–23.
- Rozert, R. (2014). Primenenie poroshkovyh provolok dlia svarki v promyshlennyh usloviiah. Avtomaticheskaia svarka, 6-7, 60–64.
- Makovetskaia, O. K. (2012). Situatsiia na rynke osnovnyh konstruktsionnyh materialov i svarochnoi tehniki v Iaponii. Svarshchik, 5, 34–41.
- Avilov, T. I. (1958). Issledovanie protsessa dugovoi svarki pod vodoi. Svarochnoe proizvodstvo, 5, 12–14.
- Madatov, N. M. (1967). Podvodnaia svarka i rezka metallov. Leningrad: Sudostroenie, 164.
- Kononenko, V. Ya. (2011). Podvodnaia svarka i rezka metallov. Kyiv: Unіversitet «Ukrayna», 264.
- Kahovskii, N. Yu., Maksimov, S. Yu. (2014). Vliianie sostava shihty poroshkovoi provoloki na stabil'nost' protsessa goreniia dugi pri mokroi podvodnoi svarke. Zbirnyk naukovykh prats Natsionalnoho universytetu korablebuduvannia, 6, 29–33.
- Balyts’kyi, O. I., Eliasz, J., Ripei, I. V. (2012, January). Influence of preliminary plastic deformation of 12Kh18N12T steel on its mechanical properties. Materials Science, Vol. 47, № 4, 438–446. doi:10.1007/s11003-012-9414-0
- Balitskii, A. I., Vitvitskii, V. I. (2009). Determination of stainless steels mechanical properties in high-pressure hydrogen. Effects of Hydrogen on Materials, 421–428.
- Kakhovskyi, M. Yu. (2014). Poroshkovyi samozakhysnyi drit dlia pidvodnoho zvariuvannia vysokolehovanoi koroziinostiikoi stali 12Kh18N10T. Molodyi vchenyi, 11, 12–15.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2016 Микола Юрійович Каховський
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.