Development of the computerized system for control of curved surfaces with the help of inductive sensors

Authors

DOI:

https://doi.org/10.15587/2312-8372.2016.58867

Keywords:

remote sensing, moving, error correction, TEDS, sine-cosine rotating transformer, inductive sensors

Abstract

The article presents the main results of research on the analog interface for remote measurement of linear and angular displacement values inductive sensors with high metrological characteristics. The main purpose of the study is to develop a computerized system for remote measurement and control of curved surfaces using inductive sensors, which provides increased performance and noise immunity.

This is achieved by creating a new multifunctional transducers based on iterative integrating converters differentially-current inputs, reduce the effects of stray capacitance electrical cables through the shunting effect is almost zero input resistance and can increase the frequency of the test signal. It is shown that at the same time increases the quality factor of the primary winding IDPTT and reduces the influence of destabilizing factors on the sensitivity of the sensor.

The presented system allows to combine in one unit features such as noise suppression, and general strengthening of the normal type and the desired signal. Commutative exchange of information between the sensors allows isolate the generator windings of the sensor from the measuring part of the analog interface, which considerably increases immunity.

The algorithm for error correction of the measurement channel using TEDS in terms of non-linearity of the channel and the inter-channel connections is proposed. Results of the study can be implemented in the instrument-making factory in the design and development of new instruments for improving the accuracy and speed of linear and angular measurements using inductive displacement sensor for remote measurements.

Author Biographies

Дмитро Петрович Орнатський, National Aviation University, ave. Kosmonavta Komarova, 1, Kyiv, Ukraine, 03058

Doctor of Technical Sciences, Professor

Department of information measuring systems

Educational and Research Institute of Information and Diagnostic Systems

Микола Валентинович Михалко, National Aviation University, ave. Kosmonavta Komarova, 1, Kyiv, Ukraine, 03058

Head of the repair and construction department

Марія Олександрівна Катаєва, National Aviation University, ave. Kosmonavta Komarova, 1, Kyiv, Ukraine, 03058

PhD student

Department of computerized electrical systems and technologies

Educational and Research Institute of Information and Diagnostic Systems

References

  1. ElKott, D. F. (2001). Automatic Sampling for CMM Inspection Planning of Free Form Surfaces. Canada, Ontario: University of Windsor, 162.
  2. Ash, J. (1992). Datchiki izmeritel'nyh sistem. Book 1. Translation from French. Moscow: Mir, 480.
  3. Translated from English: Gorshkov, B. L. (2000). Practical design techniques for sensor signal conditioning. Moscow: ZAO AVTEKS, 311.
  4. Analogue digital angle converter – processes demodulated signals the result being independent of frequency. French Patent № 2233757 from 13.06.1073. Available: http://worldwide.espacenet.com/publicationDetails/biblio?DB=worldwide.espacenet.com&II=0&ND=3&adjacent=true&locale=en_EP&FT=D&date=19750110&CC=FR&NR=2233757A1&KC=A1
  5. Erb, K., Fisher, P. (1990). Povyshenie metrologicheskih harakteristik izmeritel'nyh preobrazovatelei metodom tsifrovoi kompensatsii pogreshnostei tehnika. Kontrol'no-izmeritel'naia tehnika: ekspress-informatsiia, 42, 22–28.
  6. Voltage Output Programmable Sensor Conditioner. (2003, December). Revised January 2011. Available: http://elcodis.com/parts/5884374/PGA309.html#datasheet
  7. Ornatskyi, D. P. (2015). Metody ta zasoby pidvyshchennia metrolohichnykh kharakterystyk dystantsiinykh vymiriuvan mekhanichnykh velychyn. Odes. derzh. akad. tekhn. rehuliuvannia ta yakosti. Odessa: Odessa State Academy of Technical Regulation and Quality, 40.
  8. Nubert, G. P. (1970). Measuring Transducers of Non-electric Sizes. Translation from English. Leningrad: Energiia, 360.
  9. Shriufer, E.; In: Babak, V. P. (1992). Obrobka syhnaliv: tsyfrova obrobka dyskretyzovanykh syhnaliv. Kyiv: Lybid, 320.
  10. SCXI 8-Channel LVTD Input Module. National Instruments. Available: http://www.ni.com/pdf/products/us/4scxisc293_ETC_196.pdf

Published

2016-01-21

How to Cite

Орнатський, Д. П., Михалко, М. В., & Катаєва, М. О. (2016). Development of the computerized system for control of curved surfaces with the help of inductive sensors. Technology Audit and Production Reserves, 1(2(27), 83–90. https://doi.org/10.15587/2312-8372.2016.58867