Optimization of arc ignition process for machines of arc dimensional machining
DOI:
https://doi.org/10.15587/2312-8372.2016.86081Keywords:
automatic system, arc dimensional machining, working fluid pressure, feed rate, electrode-tool, arc ignitionAbstract
The article examines the arc ignition at the arc dimensional machining (ADM). The audit found that:
− This process not paying attention in scientific literature.
− Feed rate of the electrode-tool with no arc combustion is set non-optimal.
The main aim of research is to optimize the process of electrode-tool feed rate at the arc ignition and, thus, reduce shock loads to the electrode-tool.
The nature of the change of the working fluid pressure in the electric erosion chamber at arc ignition is given. The pressure value is experimentally determined at which the automatic change of the maximum rate to working is ensured by the system of automatic feed of the electrode-tool to the workpiece. A functional of optimal arc ignition process of arc dimensional machining is proposed. It is possible to determine the maximum permissible rate of electrode-tool feed and reduce the likelihood of tool failure during the arc ignition. Thus, during machining due to rapid electrode-tool feed in the machining area, the technological operation time is decreased.
Research results can be used by designers that create an automatic system of electrode-tool feed at dimensional (ADM), arc (EAM), blasting (BEAM) and other related electric erosion methods of metal machining.
References
- Nosulenko, V. I. (1999). Rozmirna obrobka metaliv elektrychnoiu duhoiu. Kyiv, 36.
- Meshcheriakov, G., Nosulenko, V., Meshcheriakov, N., Bokov, V. (1988). Physical and Technological Control of Arc Dimensional Machining. CIRP Annals – Manufacturing Technology, 37 (1), 209–212. doi:10.1016/s0007-8506(07)61619-9
- Nosulenko, V. I. (2006). O fizicheskoi prirode, ob obshchem i otlichiiah, tehnologicheskih vozmozhnostiah elektricheskih razriadov i klassifikatsii sposobov elektrorazriadnoi obrabotki metallov. Elektronnaia obrabotka materialov, 1, 4–14.
- Nosulenko, V. I. (2005). Razmernaia obrabotka metallov elektricheskoi dugoi. Elektronnaia obrabotka materialov, 1, 8–17.
- Nosulenko, V. I. (2005). Elektricheskaia duga v poperechnom potoke sredy-dielektrika kak istochnik tepla dlia novyh tehnologii. Elektronnaia obrabotka materialov, 2, 26–33.
- Bokov, V. M. (2015). Elektroduhove frezeruvannia. Konstruiuvannia, vyrobnytstvo ta ekspluatatsiia silskohospodarskykh mashyn, Vol. 45, Part 2, 180–188.
- Nosulenko, V. I., Yuriev, V. V. (2015). Rozmirna obrobka elektrychnoiu duhoiu otvoriv skladnoho konturu. Zbirnyk naukovykh prats Kirovohradskoho natsionalnoho tekhnichnoho universytetu. Tekhnika v silskohospodarskomu vyrobnytstvi, haluzeve mashynobuduvannia, avtomatyzatsiia, 28, 70–73.
- Sisa, O. F. (2014). Rozmirna obrobka elektrychnoiu duhoiu bichnoi poverkhni tverdosplavnoho prokatnoho valka. Konstruiuvannia, vyrobnytstvo ta ekspluatatsiia silskohospodarskykh mashyn, 44, 153–159.
- Savelenko, G., Ermolaev, Y., Sobinov, O., Gutsul, V. (2015). Development of software and hardware device of automated system of the process stabilization of arc dimensional processing. Technology Audit And Production Reserves, 1(3(21)), 22–28. doi:10.15587/2312-8372.2015.36244
- Savelenko, G. (2015). The method of automatic determination of arc sizing machining process stability. Eastern-European Journal Of Enterprise Technologies, 1(5(73)), 9–13. doi:10.15587/1729-4061.2015.36226
- Pawade, M. M., Banwait, S. S. (2013). A Brief Review of Die Sinking Electrical Discharging Machining Process towards Automation. American Journal of Mechanical Engineering, 1 (2), 43–49. doi:10.12691/ajme-1-2-4
- Zhang, M., Zhang, Q., Dou, L., Zhu, G., Dong, C. (2016). An independent discharge status detection method and its application in EAM milling. The International Journal of Advanced Manufacturing Technology, 87 (1-4), 909–918. doi:10.1007/s00170-016-8537-0
- Zhou, J. P., Liang, C. H., Teng, W. J., Xu, Y., Zhou, B. S. (2008). Study on Rules in Material Removal Rate and Surface Quality of Short Electric Arc Machining Process. Advanced Materials Research, 33-37, 1313–1318. doi:10.4028/www.scientific.net/amr.33-37.1313
- Zhou, J. P., Liang, C. H., Xu, Y., Zhou, B. S. (2013). The NC Power Supply Design of Large Current and Wide Frequency Pulse in Short Electric Arc Machining. Applied Mechanics and Materials, 278-280, 1051–1055. doi:10.4028/www.scientific.net/amm.278-280.1051
- Zhao, W., Gu, L., Xu, H., Li, L., Xiang, X. (2013). A Novel High Efficiency Electrical Erosion Process – Blasting Erosion Arc Machining. Proceedings of the Seventeenth CIRP Conference on Electro Physical and Chemical Machining, 6, 621–625. doi:10.1016/j.procir.2013.03.057
- Zhao, W. S., Gu, L., Xu, H., Li, L., Xiang, X. (2012). High-speed Electrical Arc Machining Based on Hydrodynamic Arc Breaking Mechanism. Electromachining & Mould, 300 (5), 50–54. Available: http://en.cnki.com.cn/Article_en/CJFDTOTAL-DJGU201205012.htm
- Savelenko, G. V., Ermolaev, Y. A. (2014). Study workflow dimensional processing of arc on a machine with electromechanical drive. Computer-integrated technologies: education, science and industry, 14, 164–169.
- Savelenko, H. V., Yermolaiev, Y. O.; assignee: Kirovograd State Technical University. (10.11.2015). Method for determining moment of arc ignition and change of movement mode at idling of electrode-tool of machine for size processing by stationary arc. Patent 110050 Ukraine, MPK (2006.01) B23H 7/26. B23H 7/32. B23H 1/02. B23H 7/18. G05B 13/02. H05B 7/152. Appl. № а201311270. Filed 23.09.2013. Bull. № 21, 3.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2016 Gregory Savelenko, Yury Yermolaev, Vitaly Yuriev
![Creative Commons License](http://i.creativecommons.org/l/by/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.