The study of the dynamics of the process of forming a layer of aglomeration mixture prepared for sintering

Authors

DOI:

https://doi.org/10.15587/2312-8372.2015.41403

Keywords:

segregation, agglomeration, feeding chute, thermal regime, horizon layer, charge

Abstract

A study of the dynamics of the formation of polydisperse layer of feedstock material loaded on pallets of sintering machine is conducted in this article on example of the system «feeder – straight feeding chute».

The author proposes a technique which allows to calculate the distribution of the fractional composition of the charge adjustment layer, as well as a set range of parameters of considered chute for its efficient operation. Thus, it is defined a critical angle of the chute in which violated segregation processes in the feed material.

The calculation of the distribution of fractions of polydisperse sinter charge in the case of using the straight feeding chute. It was found that the chute of similar design is very bad for the sintering conditions of sinter mix in the upper layers.

This is made a prerequisite to the selection of the type of feeding device, capable of providing the required segregation of the material fractions.

Author Biography

Антон Сергеевич Мных, Zaporozhye State Engineering Academy, Lenina 226, Zaporozhye, Ukraine, 69007

Associate Professor, Candidate of Technical Science

Department of Electrical Engineering and Energy Management

References

  1. Berezhnoi, N. N., Stoikova, Ya. A. (2012). Analiz sposobov i sistem zagruzki aglomeratsionnyh i obzhigovyh mashin konveiernogo tipa. Vіsnik KrNU, 32, 44-47.
  2. Bezverhii, I. V., Tomash, A. A. (2010). Razrabotka meropriiatii dlia uvelicheniia segregatsii aglomeratsionnoi shihty pri ee zagruzke na aglolentu. Mezhdunarodnaia nauchno-tehnicheskaia konferentsiia «Universitetskaia nauka 2010», Mariupol', Vol. 1, 40-42.
  3. Petrushov, S. N., Novohatskii, A. M. et al. (1998). Formirovanie struktury aglomeratsionnogo sloia shihty. Izv. vuzov. Chernaia metallurgiia, 8, 21-24.
  4. Kokorin, L. K., Fliagin, Yu. D.; patentee JSC "Ural Heavy Machinery Plant". (10.09.1997). Ustroistvo dlia zagruzki obzhigovoi konveiernoi mashiny. Patent RF №2089806, MPK: F27B21/10 /. Appl. 02.03.1994. 5 p.
  5. Maki, T., Sekiguchi, I. (2009). Study for Evaluation and Optimization of Iron Ore Granulation with Consideration of Dynamics and Particle Conditions. ISIJ International, Vol. 49, № 5, 631–636. doi:10.2355/isijinternational.49.631
  6. Krizhevskii, A. V., Rudovskii, G. I. et al. (1992). Vliianie granulometricheskogo sostava spekaemoi shihty na rashod aglomeratsionnogo topliva. Metallurgicheskaia i gornorudnaia promyshlennost', 1, 4-6.
  7. Paziuk, M. Yu. (1985). Vliianie uslovii zagruzki na formirovanie struktury sloia shihty. Izv. vuzov. Chernaia metallurgiia, 6, 133-136
  8. Paziuk, M. Yu. (1985). Upravlenie protsessom formirovaniia sloia aglomeratsionnoi shihty. Izv. vuzov. Chernaia metallurgiia, 10, 131-134.
  9. Mnyh, A. S. (2014). Opredelenie optimal'nogo raspredeleniia tverdogo topliva v sloe zagruzhaemoi shihty dlia vyravnivaniia teplovogo rezhima aglomeratsionnogo protsessa. Tekhnichna teplofizyka ta promyslova teploenerhetyka, 6, 47-51.
  10. Mnyh, A. S., Paziuk, M. Yu. (2014). K voprosu issledovaniia mehanizma formirovaniia sloia polidispersnoi aglomeratsionnoi shihty. Metalurhiia. Naukovi pratsi Zaporizkoi derzhavnoi inzhenernoi akademii, 2 (32), 5-9.
  11. Mnyh, A., Eriomin, A., Mnyh, I. (2015). Determination of the required segregation of fractions of sinter charge for stabilizing the thermal conditions of sintering. Eastern-European Journal Of Enterprise Technologies, 1(8(73)), 68-73. doi:10.15587/1729-4061.2015.37829

Downloads

Published

2015-04-02

How to Cite

Мных, А. С. (2015). The study of the dynamics of the process of forming a layer of aglomeration mixture prepared for sintering. Technology Audit and Production Reserves, 2(1(22), 39–42. https://doi.org/10.15587/2312-8372.2015.41403

Issue

Vol. 2 No. 1(22) (2015): Energy, energy-saving technologies and equipment. Electrical engineering and industrial electronics

Section

Energy, energy-saving technologies and equipment

License

Copyright (c) 2016 Антон Сергеевич Мных

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.