Development of the mathematical model for the choice of the optimal cutting condition with combined axial tool

Authors

  • Михаил Сергеевич Степанов National Technical University «Kharkiv Polytechnic Institute», Frunze st. 21, Kharkiv, Ukraine, 61002, Ukraine https://orcid.org/0000-0002-0848-6805
  • Марина Сергеевна Иванова National Technical University «Kharkiv Polytechnic Institute», Frunze st. 21, Kharkiv, Ukraine, 61002, Ukraine https://orcid.org/0000-0002-0848-6805

DOI:

https://doi.org/10.15587/2312-8372.2015.47795

Keywords:

combined axial tool, minute feeding, rate speed, cutting speed, performance

Abstract

Analysis of the literature showed that the issue of determining the optimum cutting conditions when processing a combined axial tool is not considered carefully enough. In this regard, in order to increase productivity and ensure the required quality of processing holes in hydraulic and pneumatic valves by combined axial tool were developed and solved the three one-criterion problem with the corresponding evaluation function: the standard deviation of the average speed of cutting; the standard deviation of the feed per revolution; processing time. The simulation results in the system MathCAD shown that the most productive cutting conditions is obtained by the function of maximum performance. The results for the one-criterion tasks suggest that there is potentially solution that satisfies all three evaluation functions, so that it was proposed to solve the problem of rational choice of cutting conditions for combined tools as minimax problem with restrictions, including three previously proposed estimators.

Author Biographies

Михаил Сергеевич Степанов, National Technical University «Kharkiv Polytechnic Institute», Frunze st. 21, Kharkiv, Ukraine, 61002

Doctor of Technical Sciences, Professor

Department of Hydropneumautomatics and Hydraulic actuator

Марина Сергеевна Иванова, National Technical University «Kharkiv Polytechnic Institute», Frunze st. 21, Kharkiv, Ukraine, 61002

Assistant

Department of Mechanical Engineering and Machine Tools

References

  1. Goranskij, G. K., Vladimirova, E. V., Lambin, L. N. (1970). Avtomatizacija tehnicheskogo normirovanija rabot na metallorezhushhih stankah s pomoshh'ju JeVM. M.: Mashinostroenie, 224.
  2. Smagin, G. I., Karmanov, V. S. (1999). Optimizacija rezhimov sverlenija po kriteriju minimuma zatrat s ispol'zovaniem dvuhfaktornyh stojkostnyh modelej. Sbornik nauchnyh trudov NGTU, 2 (15), 57–71.
  3. Coppini, N. L., Batocchio, M. C. A. (1994). Cutting conditions optimization based on expert system 3th CEM-NNE. Belém, Brazil, 564–567.
  4. Coppini, N. L., Ferreira, J. R., Miranda, G. W. A. (1997). Cutting conditions optimisation in machining of CFRP with cemented carbide Tool. ICCE/4-Fourth International Conference on Composites Engineering. Hawaii, USA, 6–11.
  5. Parker, S., Kolahan, F., Liang, M. (2000). Optimization of hole-making operations: a tabu-search approach. International Journal of Machine Tools and Manufacture, Vol. 40, № 12, 1735–1753. doi:10.1016/s0890-6955(00)00024-9
  6. Qudeiri, J. A., Yamamoto, H., Ramli, R. (2007). Optimization of operation sequence in CNC machine tools using genetic algorithm. Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol. 1, № 2, 272–282. doi:10.1299/jamdsm.1.272
  7. Zharlikov, N. V. (1961). Kombinirovannye rezhushhie instrumenty. Sverdlovsk: Mashgiz, Uralo-Sibirskoe otdel, 78.
  8. Baranovskij, Ju. V. (1972). Rezhimy rezanija metallov. M.: Mashinostroenie, 408.
  9. Malyshko, I. A. (1996). Osevye kombinirovannye instrumenty (rekomendacii po proektirovaniju i jekspluatacii). Donetsk: PKTI, 135.
  10. Karpus', V. Je., Ivanova, M. S. (2010). Analiz isnujuchyh rekomendacij shhodo pryznachennja rezhymiv rizannja kombinovanymy os'ovymy instrumentamy. Visnyk Nacional'nogo tehnichnogo universytetu “Harkivs'kyj politehnichnyj instytut”, 49, 92–96.
  11. Karpus', V. Je., Ivanov, V. O., Kotljar, O. V. et al. (2012). Intensyfikacija procesiv mehanichnoi' obrobky. Sumy: Sums'kyj derzhavnyj universytet, 436.

Published

2015-07-23

How to Cite

Степанов, М. С., & Иванова, М. С. (2015). Development of the mathematical model for the choice of the optimal cutting condition with combined axial tool. Technology Audit and Production Reserves, 4(1(24), 69–72. https://doi.org/10.15587/2312-8372.2015.47795