Forming of properties complex of copper wire by the method of combined deformation by torsion and tension
DOI:
https://doi.org/10.15587/2706-5448.2022.252282Keywords:
M1 grade copper wire, electrical application, combined plastic deformation, resistivity, stress relaxationAbstract
The object of research is the mechanical properties of copper wire M1 for electrical applications, subjected to combined torsional deformation with tensile tension. One of the most problematic aspects in the manufacturing of such a wire is its fracture during processing due to low strength and ductility. DSTU EN 13602:2010 regulates the ultimate tensile strength, relative elongation, the number of bends before fracture and the number of twists until failure. To increase the service life of the product it is necessary to increase strength and plastic properties.
The methods of influence on the material by combined plastic tensile deformation with tensile was used in the study, the mechanical characteristics (ultimate tensile strength, true deformation before failure, relative elongation, relative reduction in area) and electrical conductivity were determined. Statistical analysis tools were used for modeling and graphical displaying of data.
The proposed approach allows to select the modes of combined torsional deformation with tensile, providing the optimal combination of tensile strength and relative narrowing of M1 grade copper wire. Under certain modes of such deformation, with increasing degree of deformation, it is possible to increase the strength characteristics and at the same time obtain high values of plasticity.
The obtained results of approbation of different combined deformation modes allow to consider it an effective tool for achieving high values of true rapture stress and ultimate deformation in order to improve the service characteristics of the deformed wire. It is shown that relaxation processes occur during such treatment, which leads to a decrease in stresses and a sharp increase in plastic characteristics. Clarification of the mechanisms of the characteristics formation allows to control the features of the structure and, accordingly, the level of mechanical properties to obtain a wire that combines high strength with high toughness. This makes it possible to develop deformation modes to obtain copper wire with special properties depending on customer requirements, for example: strong wire with low electrical resistance.
References
- Pashinskaia, E. G. (2009). Fiziko-mekhanicheskie osnovy izmelcheniia struktury pri kombinirovannoi plasticheskoi deformatsii. Donetsk: Izdatelstvo «Veber», 352.
- Utiashev, F. Z., Raab, G. I., Valitov, V. A. (2020). Deformatsionnoe nanostrukturirovanie metallov i splavov. Saint Petersburg: Naukoemkie tekhnologii, 185.
- Segal, V. M. (1995). Materials processing by simple shear. Materials Science and Engineering: A, 197 (2), 157–164. doi: http://doi.org/10.1016/0921-5093(95)09705-8
- Xue, Q., Liao, X. Z., Zhu, Y. T., Gray, G. T. (2005). Formation mechanisms of nanostructures in stainless steel during high-strain-rate severe plastic deformation. Materials Science and Engineering: A, 410-411, 252–256. doi: http://doi.org/10.1016/j.msea.2005.08.022
- Nagaraj, M., Ravisankar, B. (2018). Effect of Severe Plastic Deformation on Microstructural and Mechanical Properties of Structural Steel IS2062. Transactions of the Indian Institute of Metals, 71 (9), 2315–2323. doi: http://doi.org/10.1007/s12666-018-1363-3
- Kawasaki, M., Langdon, T. G. (2008). The significance of strain reversals during processing by high-pressure torsion. Materials Science and Engineering: A, 498 (1-2), 341–348. doi: http://doi.org/10.1016/j.msea.2008.08.021
- Li, J., Li, F., Zhao, C., Chen, H., Ma, X., Li, J. (2016). Experimental study on pure copper subjected to different severe plastic deformation modes. Materials Science and Engineering: A, 656, 142–150. doi: http://doi.org/10.1016/j.msea.2016.01.018
- Zhang, J., Huang, Z., Rui, W., Li, J., Tian, Y., Li, J. (2019). Effect of Combined Torsion and Tension on the Microstructure and Fracture Behavior of 316L Austenitic Stainless Steel. Journal of Materials Engineering and Performance, 28 (9), 5691–5701. doi: http://doi.org/10.1007/s11665-019-04316-4
- Dong, H., Guo, F., Huang, W., Yang, X., Zhu, X., Li, H., Jiang, L. (2021). Shear banding behavior of AA2099 Al-Li alloy in asymmetrical rolling and its effect on recrystallization in subsequent annealing. Materials Characterization, 177, 111155. doi: http://doi.org/10.1016/j.matchar.2021.111155
- Ren, X., Huang, Y., Zhang, X., Li, H., Zhao, Y. (2021). Influence of shear deformation during asymmetric rolling on the microstructure, texture, and mechanical properties of the AZ31B magnesium alloy sheet. Materials Science and Engineering: A, 800, 140306. doi: http://doi.org/10.1016/j.msea.2020.140306
- Naydenkin, E. V., Mishin, I. P., Ratochka, I. V., Oborin, V. A., Bannikov, M. V., Bilalov, D. A., Naydenkin, K. E. (2021). Fatigue and fracture behavior of ultrafine-grained near β titanium alloy produced by radial shear rolling and subsequent aging. Materials Science and Engineering: A, 810, 140968. doi: http://doi.org/10.1016/j.msea.2021.140968
- Naizabekov, A., Lezhnev, S., Arbuz, A., Panin, E. (2018). The effect of radial-shear rolling on microstructure and mechanical properties of stainless austenitic steel AISI-321. MATEC Web of Conferences, 190, 11003. doi: http://doi.org/10.1051/matecconf/201819011003
- Gamin, Y. V., Muñoz Bolaños, J. A., Aleschenko, A. S., Komissarov, A. A., Bunits, N. S., Nikolaev, D. A. et. al. (2021). Influence of the radial-shear rolling (RSR) process on the microstructure, electrical conductivity and mechanical properties of a Cu–Ni–Cr–Si alloy. Materials Science and Engineering: A, 822, 141676. doi: http://doi.org/10.1016/j.msea.2021.141676
- Zhilyaev, A. P., Shakhova, I., Belyakov, A., Kaibyshev, R., Langdon, T. G. (2013). Wear resistance and electroconductivity in copper processed by severe plastic deformation. Wear, 305 (1-2), 89–99. doi: http://doi.org/10.1016/j.wear.2013.06.001
- Pashinskaia, E. G., Podrezov, Iu. N., Verbilo, D. G., Kraliuk, M. A., Danilenko, N. I. (2014). Vliianie parametrov intensivnoi kombinirovannoi plasticheskoi deformatsii na mekhanicheskie svoistva medi. Deformatsiia i razrushenie, 1, 9–15.
- Taylor, J. I. (1928). Hardening of aluminium at the plastic deformation. Journal of the Institute of Metals, 62, 307–311.
- Trefilov, V. I., Moiseev, V. F., Pechkovskii, E. P. et. al. (1989). Deformatsionnoe uprochnenie i razrushenie polikristallicheskikh metallov. Kyiv: Naukova dumka, 256.
- Podrezov, Iu. N., Firstov, S. A. (2006). Dva podkhoda k analizu krivykh deformatsionnogo uprochneniia. Fizika i tekhnika vysokikh davlenii, 15 (4), 17–34.
- Zavdoveev, A., Len, A., Pashinska, E. (2020). Small Angle Neutron Scattering Study of Nanoscale Structure of Low-Carbon Steel After Rolling with Shear Followed by Cold Drawing. Metals and Materials International, 27 (3), 481–487. doi: http://doi.org/10.1007/s12540-020-00766-x
- Zavdoveev, A., Baudin, T., Rogante, M., Pashinska, E., Skoryk, M. (2020). Shear impact during steel wire drawing on grain boundaries and mechanical properties. Letters on Materials, 10 (4s), 558–565. doi: http://doi.org/10.22226/2410-3535-2020-4-558-565
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Olena Pashynska, Volodymyr Pashynskyi, Maryna Kraliuk, Igor Boyko
![Creative Commons License](http://i.creativecommons.org/l/by/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.