Research manufacturing process of corrugated packaging products

Authors

  • Олена Миколаївна Гумен National Technical University of Ukraine "Kyiv Polytechnic Institute" Peremohy 37, Kyiv, 03056, Ukraine
  • Степан Миколайович Гумен National Technical University of Ukraine "Kyiv Polytechnic Institute" Peremohy 37, Kyiv, 03056, Ukraine
  • Петро Миколайович Яблонський National Technical University of Ukraine "Kyiv Polytechnic Institute" Peremohy 37, Kyiv, 03056, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2013.9283

Keywords:

corrugated cardboard, packaging, quality control.

Abstract

Recently it has been preferred packaging of corrugated cardboard and cardboard. Although the material of the packing will be made depending on the product that will be in it, and its characteristics. Nowadays the most common packaging material is cardboard. Notable among different types of this material is corrugated paperboard profile (corrugated cardboard).
Modern printed packaging products are made from various grades of paper and paperboard. Great demand today is cardboard and corrugated packaging quality, primarily because consumers pay attention to the type of packaging.
To ensure proper packaging of products, it is necessary to analyze the materials and the type of required packaging products and manufacturing quality control stages. Such quality control can eliminate potential problems in the manufacturing process with minimal losses.
After considering the method of manufacturing of corrugated cardboard in this paper was built a block diagram of the process of manufacturing three-layer corrugated board and developed an algorithm for the process of manufacturing of corrugated cardboard packaging. Proper tracking of each stage of the manufacturing process allows us to determine what quality may suffer in the future, and to find the optimum how to fix this.

Author Biographies

Олена Миколаївна Гумен, National Technical University of Ukraine "Kyiv Polytechnic Institute" Peremohy 37, Kyiv, 03056

Professor

Department of descriptive geometry, engineering and computer graphics

Степан Миколайович Гумен, National Technical University of Ukraine "Kyiv Polytechnic Institute" Peremohy 37, Kyiv, 03056

Lecturer

Department of reprographics

Петро Миколайович Яблонський, National Technical University of Ukraine "Kyiv Polytechnic Institute" Peremohy 37, Kyiv, 03056

Lecturer

Department of descriptive geometry, engineering and computer graphics

References

  1. Упаковка (2011), Доступ з: http://www.packaging.kiev.ua/rus/ content/magazine/article/54 (6 травня 2011).
  2. Бумага и жизнь (2006), Доступ з: http://paperandlife.com/journal/ onlinejournal/2006/may/first_swallow/ (22 травня 2011).
  3. Жидецький, Ю.Ц. Поліграфічні матеріали [Текст] / Ю.Ц. Житецький, О.В. Лазаренко та ін. – Львів, Афіша, 2001. – 328 с.
  4. Романо, Ф. Современные технологии издательско-полиграфической отрасли [Текст] / Ф.Романо. – М.: Принт-Медиа бизнес, 2006. – 457 с.
  5. Семенова А.А. Контроль рабочих свойств полиграфических материалов [Текст] /А.А. Семенова. – Минск: Книга, 1964. – 488 с.
  6. Кривошей, В.М. Упаковка в нашому житті [Текст] /В.М. Кривошей. – К.: ІАЦ Упаковка, 2001. – 160с.

Downloads

Published

2013-02-05

How to Cite

Гумен, О. М., Гумен, С. М., & Яблонський, П. М. (2013). Research manufacturing process of corrugated packaging products. Eastern-European Journal of Enterprise Technologies, 1(5(61), 25–29. https://doi.org/10.15587/1729-4061.2013.9283

Issue

Vol. 1 No. 5(61) (2013): The applied physics and materials technology

Section

Applied physics

License

Copyright (c) 2014 Олена Миколаївна Гумен, Степан Миколайович Гумен, Петро Миколайович Яблонський

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.