Reducing the cost of stamping by engraving with prototyping

Authors

  • Андрей Сергеевич Гордеев Кафедра полиграфического производства и компьютерной графики Украинская инженерно-педагогическая академия г. Харьков, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2010.3333

Keywords:

plate, stamping, prototyping, run length, printing technology, laser sintering

Abstract

The aim is to develop a method of manufacturing technologies cliche prototyping. For the production of plates for embossing method was used SLS - a way of selective laser sintering. Applying technology SLS rapid prototyping and material LaserForm A6 was made stamp for stamping.

Author Biography

Андрей Сергеевич Гордеев, Кафедра полиграфического производства и компьютерной графики Украинская инженерно-педагогическая академия г. Харьков

Доктор технических наук, доцент, заведующий кафедрой

References

  1. Борисов Б. Печатные и отделочные процессы. Материалы [6-й международной выставки «ПИЛИГРАФБУДМАШ», Москва, май 1991] // Полиграфия. – 1991. – № 9. – с.7-10.
  2. Гарячева А., Соболева Ю. Пути повышения качества клише. Полиграфия, 1983, №10, с 6-8.
  3. Грабченко А.И., Чернышов С.И., Верезуб Н.В., Витязев Ю.Б., Доброскок В.Л., Кнут Х. Интегрированные технологии ускоренного прототипирования и изготовления. Монография: 2-е изд., перераб. и доп. / Товажнянский Л.Л., Лиерат Ф. / Под. ред. Л.Л. Товажнянского, А.И. Грабченко. - Харьков: ОАО «Модель Вселенной», 2005.
  4. Шпак А.П., Майборода В.П., Куницкий Ю.А., Рево С.Л Нанослоистые композиционные материалы и покрытия. - К.: Издательский дом академической периодики, 2004. – 164 с.

Downloads

Published

2010-11-10

How to Cite

Гордеев, А. С. (2010). Reducing the cost of stamping by engraving with prototyping. Eastern-European Journal of Enterprise Technologies, 6(5(48), 55–57. https://doi.org/10.15587/1729-4061.2010.3333

Issue

Vol. 6 No. 5(48) (2010): The applied physics and materials technology

Section

Applied physics

License

Copyright (c) 2014 Андрей Сергеевич Гордеев

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.