The influence of mechanical error compensator on the quality of thin-sheet separating stamping

Authors

DOI:

https://doi.org/10.15587/1729-4061.2015.54276

Keywords:

separating stamping, "press-stamp" system errors, mechanical compensator, stamping quality

Abstract

The quality of the thin-sheet separating stamping depends on the state of the "press-stamp" system, namely the state of the press (rigidity and geometric accuracy) and the deformation degree of the guide assemblies in the stamp and stamping unit plates as a result of the action of technological effort. To reduce the impact of these deformations, different approaches are used: from increasing the rigidity of the unit by the number of guide assemblies and plate thickness to applying compensating devices for unloading the unit from the action of transverse forces and torques. Known compensating devices only partially solve the problem, which is not enough for the conditions of the thin-sheet separating stamping. According to the authors, the deformation of the units can be substantially reduced using the mechanical error compensator of the "press-stamp" system, mounted on the press table instead of the bolster plate, which should positively affect the quality of thin-sheet stamped parts.

In the paper, the effect of mechanical compensator on the stress-strain state of the stamping unit elements and the quality of the thin-sheet separating stamping of the rotor plates was examined through a comparative analysis.

It was found that using the compensator substantially reduces the deformation of the bottom plate of the stamping unit, which leads to more favorable operating conditions of the stamp guide assemblies. The rotation angle of columns, as a result of deformation of the unit plates, has decreased several times.

The mechanism of the effect of the compensator on the stamping quality indices was determined. Measuring variations in the sizes of the rotor plates showed that during stamping with compensator, the deviation is 2.25 - 2.40 times lower than without it, and the distribution density of sizes during stamping with compensator is 30 - 40% higher.

Thus, the research shows the feasibility of using the proposed mechanical error compensator of the "press-stamp" system to enhance the quality of the thin-sheet separating stamping, especially in large scale and mass production of parts such as core plates.

Author Biographies

Володимир Якович Мірзак, Kirovograd National Technical University University 8, Kirovograd, Ukraine, 25006

senior Lecturer

Department treatment of metals and special technologies pressure

Віктор Михайлович Боков, Kirovograd National Technical University University 8, Kirovograd, Ukraine, 25006

Professor, Candidate of technical science

Department treatment of metals and special technologies pressure

References

  1. Xin-jian, L. U., Zun-mang, K. E., Si-hong, Z. H. U., Jun, Z. (2010). Research on bottom dead center (BDC) of high speed precision press [J]. Forging & Stamping Technology, 1, 1–23. Available at: http://en.cnki.com.cn/Article_en/CJFDTOTAL-DYJE201001023.htm
  2. Wang, L., Xu, F.-Y., Wang, X.-S. (2012). Analysis of thermally induced machine tool errors of a crank press. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 226 (9), 1465–1478. doi: 10.1177/0954405412451071
  3. Yavtushenko, O. V. (2012). Silovye usloviya ustojchivosti polzuna odnokrivoshipnogo. Vіsnik SevNTU. Serіya: Mehanіka, energetika, ekologіya, 133, 260–268.
  4. Titarenko, N. I. (1980). Tochnost sistemyi press-shtampovyiy blok. Kiev: Naukova dumka, 135.
  5. Mirzak, V. Ya., Bokov, V. M. (2012). Sposib tonkolystovogo rozdilovogo shtampuvannja v systemi «pres-shtamp» z bezzazornym naprjamkom ruhomoi' chastyny shtampa vidnosno neruhomoi'. Patent 70346 of Ukraine. V26F1/40. № u201113040; declared 07.11.2011; published 11.06.2012, № 11.
  6. Kuznecov, S. V. (2014). Vliyanie poperechnyh sil na kachestvo detalej, poluchaemyh metodami listovoj shtampovki. Trudy Nizhegorodskogo gosudarstvennogo tehnicheskogo universiteta, 5 (107), 438–442.
  7. GOST 16719-71. (2006). Hvostoviki plavayushhie dlya shtampov listovoj shtampovki. Konstrukciya i razmery. Moscow: Standartinform, 10.
  8. Rudman L. I. ed. (1988). Spravochnik konstruktora shtampov. Listovaya shtampovka. Moscow: Mashinostroenie, 496.
  9. Diamantopulo, K. K., Kuhar, V. V., Evteev, A. I. (2005). Kompensaciya nesoosnosti sistemy «press-shtamp» iznoshenogo shtampovochnogo oborudovaniya. Metallurgicheskie processy i oborudovanie, 2, 31–34.
  10. Balalaeva, E. Yu. (2011). Raschyot universalnyih uprugih kompensatorov pogreshnostey sistemyi «press-shtamp» dlya operatsii vyityazhki-formovki. Obrabotka materialov davleniem. Kramatorsk: DGMA, 1 (26), 193–198.
  11. Kuhar, V. V. (2009). Snizhenie pogreshnosti v sisteme press-shtamp i bezruchevoe profilirovanie zagotovok na pressah. Vestnik NTU "HPI", 37, 54–62.
  12. Kachanov, A. P., Mirzak, V. Ya., Zaporozhchenko, V. S. (1996). Povyshenie stojkosti razdelitelnyh shtampov za schet ispolzovaniya mehanicheskih kompensatorov. Kuznechno-shtampovochnoe proizvodstvo, 4, 18–22.
  13. Mirzak, V. Ya., Bokov V. M. (2014). Modeljuvannja pokaznykiv micnosti mehanichnogo kompensatora pohybok systemy «pres-shtamp» iz zastosuvannjam metoda skinchennyh elementiv. Tehnika v sil's'kogospodars'komu vyrobnyctvi, galuzeve mashynobuduvannja, avtomatyzacija. Kirovograd: KNTU, 27, 3–12.
  14. Smirnov-Alyaev, G. A., Chikidovskiy, V. P. (1972). Eksperimentalnyie issledovaniya v obrabotke metallov davleniem. Leningrad: Mashinostroenie, 360.

Downloads

Published

2015-12-25

How to Cite

Мірзак, В. Я., & Боков, В. М. (2015). The influence of mechanical error compensator on the quality of thin-sheet separating stamping. Eastern-European Journal of Enterprise Technologies, 6(7(78), 10–15. https://doi.org/10.15587/1729-4061.2015.54276

Issue

Vol. 6 No. 7(78) (2015): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2015 Володимир Якович Мірзак, Віктор Михайлович Боков

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.