Contour milling programming technology for virtual basing on a CNC machine

Authors

DOI:

https://doi.org/10.15587/1729-4061.2019.162673

Keywords:

virtual basing, contour milling on a CNC machine, preparation of a control program

Abstract

A new technique and an application program for automating the programming of the milling operation during virtual basing of the workpiece on the CNC machine table is presented, when precise installation of the workpiece along the coordinate axes of the machine is difficult. The solution of such a scientific and technical problem allows you to perform contour milling of parts with their arbitrary location on the table of the CNC machine with guaranteed alignment of the allowance along the forming path. The method involves the sequential implementation of three stages with parallel use of the created application program. At the first stage, an electronic copy of the part drawing is prepared, which contains the selected part and workpiece contour highlighted in different colors. Thus, the scanning provides automatic creation of digital two-dimensional arrays of geometric images necessary to solve the problem. At the second stage, the coordinates of three points of the workpiece measured by the probe on the machine are entered into the created program. Based on the entered data, the created program solves the problem of alignment of the allowance using the Gauss-Seidel method using the Hausdorff dimension. This approach allows us to obtain a quantitative estimate of the similarity of polygonal objects, which is necessary to solve the problem of minimax location of the allowance. The task is to determine the correction of the control program for two linear coordinates and one angular around the center of mass of the workpiece. At the third stage, the correction values calculated in the program are entered into the CNC rack of the machine and the processing of the contour begins. The proposed technique and the created application program were tested when processing the part contour on a VF-3 HAAS milling machine. Practical testing has shown the effectiveness of the technique, which is to ensure milling without overloading the tool and reduce the processing time during virtual basing of the workpiece

Author Biographies

Yuri Petrakov, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” Peremohy ave., 37, Kyiv, Ukraine, 03056

Doctor of Technical Sciences, Professor, Head of Department

Department of Manufacturing Engineering

Danylo Shuplietsov, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” Peremohy ave., 37, Kyiv, Ukraine, 03056

Postgraduate student

Department of Manufacturing Engineering

References

  1. Suh, S.-H., Kang, S. K., Chung, D.-H., Stroud, I. (2008). Theory and Design of CNC Systems. Springer. doi: https://doi.org/10.1007/978-1-84800-336-1
  2. Fundamentals of CNC Machining (2014). Autodesk. Available at: https://academy.titansofcnc.com/files/Fundamentals_of_CNC_Machining.pdf
  3. Zhu, S. W., Ding, G. F., Ma, S. W., Yan, K. Y., Qin, S. F. (2013). Workpiece locating error prediction and compensation in fixtures. The International Journal of Advanced Manufacturing Technology, 67 (5-8), 1423–1432. doi: https://doi.org/10.1007/s00170-012-4578-1
  4. Evchenko, K. G. et. al. (2013). Vortex strategy and Machine DNA optimization technology from Delcam Company are new possibilities to improve milling performance Avtom. Avtom. Prom., 5, 20–22.
  5. Nosov, P. S., Yalansky, A. D., Іakovenko, V. О. (2013). 3D Modelling of rehabilitation corset with use of powershape delcam. Information technologies in education, science and production, 1 (2), 222–230.
  6. Spencer, R. M., Christopher, O. (1989). Pat. No. US4833790A USA. Method and system for locating and positioning circular workpieces. No. 48,194; declareted: 11.05.1987; published: 30.05.1989.
  7. Koltsov, A. G., Blokhin, D. A., Krivonos, E. V., Narezhnev, A. N. (2016). Influence assessment of metal-cutting equipment geometrical accuracy on OMV-technologies accuracy. 2016 Dynamics of Systems, Mechanisms and Machines (Dynamics). doi: https://doi.org/10.1109/dynamics.2016.7819029
  8. Radu, P. Adaptive Machining for High Precision Fabrication. Available at: http://www.mapyourshow.com/MYS_Shared/imts16/handouts/RaduPavelIMTS57.pdf
  9. Petrakov, Y., Shuplietsov, D. (2017). Programming of adaptive machining for end milling. Mechanics and Advanced Technologies, 1 (79), 34–40. doi: https://doi.org/10.20535/2521-1943.2017.79.97342
  10. Lee, S.-K., Ko, S.-L. (2002). Development of simulation system for machining process using enhanced Z map model. Journal of Materials Processing Technology, 130-131, 608–617. doi: https://doi.org/10.1016/s0924-0136(02)00761-6
  11. Belogay, E., Cabrelli, C., Molter, U., Shonkwiler, R. (1997). Calculating the Hausdorff distance between curves. Information Processing Letters, 64 (1), 17–22. doi: https://doi.org/10.1016/s0020-0190(97)00140-3
  12. Guthe, M., Borodin, P., Klein, R. (2005). Fast and accurate Hausdorff distance calculation between meshes. Conference proceedings.

Downloads

Published

2019-04-08

How to Cite

Petrakov, Y., & Shuplietsov, D. (2019). Contour milling programming technology for virtual basing on a CNC machine. Eastern-European Journal of Enterprise Technologies, 2(1 (98), 54–60. https://doi.org/10.15587/1729-4061.2019.162673

Issue

Vol. 2 No. 1 (98) (2019): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2019 Yuri Petrakov, Danylo Shuplietsov

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.