Development of a new process for expanding stepped tapered rings
DOI:
https://doi.org/10.15587/1729-4061.2019.160395Keywords:
stepped tapered ring, expanding, stepped die, distribution of deformations, shape change, taperAbstract
A new method for expanding large-size tapered rings with a stepped profile has been considered. The proposed method consists in expanding the blank with the help of a stepped die. A procedure for conducting studies by the method of finite elements was proposed. The procedure is intended to determine dependences of the stress-strain state and shape change during the expanding process by means of a stepped die. Variable parameters included relative height of the stepped blank protrusion which varied in the range of 2.2...2.5. Based on the finite-element modeling, distribution of deformation rate in the forging section after expanding with the help of a stepped die was established. The forging taper formed by expanding in this way was determined. Results of finite-element modeling were verified by experimental studies with lead and steel specimens. A procedure for conducting experimental studies was proposed. The finite-element modeling has allowed us to establish that expanding with the help of a stepped die results in a tapered forging shape. This is explained by the fact that when the wall is reduced, tangential deformation of the annular blank in the wall zone is larger than that in the protrusion zone because of different height of the stepped blank. The results of finite-element modeling were confirmed by experiments in laboratory conditions with lead and steel specimens. Increase in diameter of the blank protrusion leads to an increase in rate of the protrusion deformation which causes an increase in diameter of the protrusion bore. Analysis of macrostructure of the annular forging with a tapered stepped profile has made it possible to establish that when the stepped blank is shaped with the help of a stepped die, metal fibers repeat the target part contour which prevents their cutting during machining. The study has established that expanding of stepped tapered blanks is realizable. It expands technological potentials of the process of expanding large-sized forgingsReferences
- Markov, O., Zlygoriev, V., Gerasimenko, O., Hrudkina, N., Shevtsov, S. (2018). Improving the quality of forgings based on upsetting the workpieces with concave facets. Eastern-European Journal of Enterprise Technologies, 5 (1 (95)), 16–24. doi: https://doi.org/10.15587/1729-4061.2018.142674
- Xu, B., Sun, M., Li, D. (2014). The void close behavior of large ingots during hot forging. 19th International forgemasters meeting. Makuhari, 141–145.
- Rutskii, D. V., Zyuban, N. A., Chubukov, M. Y. (2016). Features of Structure and Solidification of Extended Double Ingots for Hollow Forgings. Part 1. Metallurgist, 60 (1-2), 156–163. doi: https://doi.org/10.1007/s11015-016-0267-x
- Wang, J., Fu, P., Liu, H., Li, D., Li, Y. (2012). Shrinkage porosity criteria and optimized design of a 100-ton 30Cr2Ni4MoV forging ingot. Materials & Design, 35, 446–456. doi: https://doi.org/10.1016/j.matdes.2011.09.056
- Kolodkin, M. V., Zhul’ev, S. I., Dub, V. S., Romashkin, A. N., Mal’ginov, A. N. (2010). Choice of a rational scheme for casting of a forging ingot for producing hollow forgings. Russian Metallurgy (Metally), 2010 (6), 544–547. doi: https://doi.org/10.1134/s0036029510060169
- Shamrei, V. A., Zhul’ev, S. I. (2007). New shape of forging ingot for making hollow forged products. Metallurgist, 51 (11-12), 617–623. doi: https://doi.org/10.1007/s11015-007-0112-3
- Shinozaki, T., Komura, T., Fujitsuna, N. et. al. (2014). Fabrication and properties of the heavy-wall ring forgings with modified 9Сr-1Mo steel for high-temperature and high-pressure reactor. 19th International forgemasters meeting. Makuhari, 397–400.
- Tanaka, Y. (2015). Reactor pressure vessel (RPV) components: processing and properties. Irradiation Embrittlement of Reactor Pressure Vessels (RPVs) in Nuclear Power Plants, 26–43. doi: https://doi.org/10.1533/9780857096470.1.26
- Jaouen, O., Costes, F., Lasne, P., Barbelet, M. (2014). From hollow ingot to shell with a powerful numerical simulation software tool. 19th International forgemasters meeting. Makuhari, 513–518.
- Tomlinson, M., Talamantes-Silva, J., Davies, P. (2011). The development of hollow ingot technology at Sheffield Forgemasters International Ltd. 18th International forgemasters meeting. Pittsburgh, 175–178.
- Girardin, G., Jobard, D., Perdriset, F. et. al. (2011). Hollow ingots: thirty years of use to control segregation and quality for nuclear and petrochemical large shells. 18th International forgemasters meeting. Pittsburgh, 170–174.
- Dragobetskii, V., Zagirnyak, M., Naumova, O., Shlyk, S., Shapoval, A. (2018). Method of Determination of Technological Durabilityof Plastically Deformed Sheet Parts of Vehicles. International Journal of Engineering & Technology, 7 (4.3), 92–99. doi: https://doi.org/10.14419/ijet.v7i4.3.19558
- Raz, K., Vaclav, K. (2014). Using of a Hydraulic Press in Production and Manufacturing of Large Rings. Procedia Engineering, 69, 1064–1069. doi: https://doi.org/10.1016/j.proeng.2014.03.091
- Cechura, M., Smolik, J. (2012). Development and innovations of existing design solutions of forming machines. Research report, CK-SVT-WP11, CVTS. Pilsen.
- Onodera, S., Kawaguchi, S., Tsukada, H., Moritani, H., Suzuki, K., Sato, I. (1985). Manufacturing of ultra-large diameter 20 MnMoNi 5 5 steel forgings for reactor pressure vessels and their properties. Nuclear Engineering and Design, 84 (2), 261–272. doi: https://doi.org/10.1016/0029-5493(85)90196-7
- Kawaguchi, S., Moritani, H., Tsukada, H., Suzuki, K., Murai, E., Sato, I. (1984). Current forging technology for integrated type steel forgings for nuclear steam supply system components. Nuclear Engineering and Design, 81 (2), 219–229. doi: https://doi.org/10.1016/0029-5493(84)90009-8
- Suzuki, K., Sato, I., Tsukada, H. (1994). Manufacturing and material properties of ultralarge size forgings for advanced BWRPV. Nuclear Engineering and Design, 151 (2-3), 513–522. doi: https://doi.org/10.1016/0029-5493(94)90192-9
- Balcar, M., Zelezný, R., Sochor, L. et. al. (2008). The development of a chill mould for tool steels using numerical modelling. Materials and technology, 42 (4), 183–188.
- Lee, S., Lee, Y., Moon, Y. (2011). Effect of deformation and heat treatment on fabrication of large sized ring by mandrel forging of hollow ingot. Materials Research Innovations, 15 (sup1), s458–s462. doi: https://doi.org/10.1179/143307511x12858957675750
- Pastore, A., Guyot, E., Dairon, J., Lemoine, M. (2014). Forging of heavy products for nuclear fuel containers. 19th International forgemasters meeting. Makuhari, 244–247.
- Markov, O. E., Oleshko, M. V., Mishina, V. I. (2011). Development of Energy-saving Technological Process of Shafts Forging Weighting More Than 100 Tons without Ingot Upsetting. Metalurgical and Mining Industry, 3 (7), 87–90. Available at: http://www.metaljournal.com.ua/assets/Uploads/attachments/87Markov.pdf
- Markov, O. E., Perig, A. V., Markova, M. A., Zlygoriev, V. N. (2015). Development of a new process for forging plates using intensive plastic deformation. The International Journal of Advanced Manufacturing Technology, 83 (9-12), 2159–2174. doi: https://doi.org/10.1007/s00170-015-8217-5
- Kukhar, V., Burko, V., Prysiazhnyi, A., Balalayeva, E., Nyhnibeda, M. (2016). Development of alternative technology of dual forming of profiled workpiece obtained by buckling. Eastern-European Journal of Enterprise Technologies, 3 (7 (81)), 53–61. doi: https://doi.org/10.15587/1729-4061.2016.72063
- Markov, O. E. (2012). Forging of large pieces by tapered faces. Steel in Translation, 42 (12), 808–810. doi: https://doi.org/10.3103/s0967091212120054
- Zhbankov, I. G., Markov, O. E., Perig, A. V. (2014). Rational parameters of profiled workpieces for an upsetting process. The International Journal of Advanced Manufacturing Technology, 72 (5-8), 865–872. doi: https://doi.org/10.1007/s00170-014-5727-5
- Markov, O. E., Perig, A. V., Zlygoriev, V. N., Markova, M. A., Grin, A. G. (2016). A new process for forging shafts with convex dies. Research into the stressed state. The International Journal of Advanced Manufacturing Technology, 90 (1-4), 801–818. doi: https://doi.org/10.1007/s00170-016-9378-6
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 Oleg Markov, Oleksiy Gerasimenko, Leila Aliieva, Alexander Shapoval, Maksym Kosilov
![Creative Commons License](http://i.creativecommons.org/l/by/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.