Research of hydrodynamics and heat transfer during the transverse air flow of a row of cylinders with screw grooves

Authors

DOI:

https://doi.org/10.15587/1729-4061.2020.205656

Keywords:

heat transfer, hydrodynamics, heat transfer intensification, hydraulic resistance, spiral grooves, Reynolds analogy

Abstract

Cylinder cross-flow is a common phenomenon in many fields of technology. Technological simplicity of tubular structures makes them attractive, especially when using working bodies that are under different pressure values. However, the cylinders belong to the category of «poorly streamlined» bodies, and there are many opportunities to improve their hydrodynamics and heat transfer. For a circular cylinder, there is a speed range in which its hydraulic resistance can decrease due to the deformation of the cylinder surface. This phenomenon can be used for the rational design of heat exchangers.

In the open-type wind tunnel, heat transfer coefficients and hydraulic resistances of single-row cylinder bundles with several types of spiral grooves on the outer surface have been determined. The largest increase in heat transfer (64 %) was shown by the cylinder with the smallest pitch of the groove (10 mm), the second place was taken by the cylinder with a relatively large step – 40 mm.

Using the best spiral groove allowed reducing the hydraulic resistance by 19 %. Visualization and computer simulation have been used to explain the effects. The conformity of computer simulations to the experimental results was determined by comparing the average heat transfer coefficient (calculated and determined using an ice calorimeter). As a result, the turbulence model RNG_kε has been chosen, which provides a better fit of the experimental model. Computer simulations have explained the physical picture of the flow around cylinders with spiral grooves, including their mutual influence with a different axial orientation in the bundle.

It has been shown that the presence of a spiral groove, which on the one hand increases heat transfer and on the other hand reduces hydraulic resistance, can significantly increase thermohydraulic efficiency (Reynolds analogy factor).

Author Biographies

Artem Khalatov, Institute of Engineering Thermophysics of National academy of sciences of Ukraine Mariyi Kapnist str., 2а, Kyiv, Ukraine, 03057

Doctor of Technical Sciences, Professor, Academician of NAS of Ukraine, Head of Department

Department of High-Temperature Thermogasdynamics

Glib Kovalenko, Institute of Engineering Thermophysics of National academy of sciences of Ukraine Mariyi Kapnist str., 2а, Kyiv, Ukraine, 03057

PhD, Senior Researcher

Department of High-Temperature Thermogasdynamics

Mariia Muliarchuk, National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute" Peremohy ave., 37, Kyiv, Ukraine, 03056

Postgraduate Student

Department of Power Systems Physics

References

  1. Migay, V. K., Firsova, E. V. (1986). Teploobmen i gidravlicheskoe soprotivlenie puchkov trub. Leningrad: Nauka, 176.

    Schlichting, H., Gersten, K. (2017). Boundary-Layer Theory. Springer. doi: https://doi.org/10.1007/978-3-662-52919-5

    Eiffel, G. (1912). Sur la resistance des spheres dans l’air en movement. Comptes Rendus, 155, 1597.

    Kovalenko, G. V., Khalatov, A. A. (2003). Fluid Flow and Heat Transfer Features at a Cross-Flow of Dimpled Tubes in a Confined Space. Volume 5: Turbo Expo 2003, Parts A and B. doi: https://doi.org/10.1115/gt2003-38155

    Kovalenko, G. V., Meyris, A. Zh. (2013). Comparison of different methods of heft transfer enhancement on the cylindrical surfaces different methods of hes. Eastern-European Journal of Enterprise Technologies, 3 (12 (63)), 58–60. Available at: http://journals.uran.ua/eejet/article/view/14882/12686

    Spitsyn, V. E., Botsula, A. L., Solomonyuk, D. N., Chobenko, V. N. (2008). Vysokoeffektivnaya gazoturbinnaya ustanovka dlya GPA. Vestnik Natsional'nogo tehnichnskogo universiteta «KhPI», 34, 8–11.

    Laidoudi, H., Blissag, B., Bouzit, M. (2018). Numerical Investigation of Mixed Convection Heat Transfer in Steady Flow Past a Row of Three Square Cylinders. Defect and Diffusion Forum, 389, 164–175. doi: https://doi.org/10.4028/www.scientific.net/ddf.389.164

    Islam, S. U., Rahman, H., Zhou, C. Y. (2016). Effect of gap spacings on flow past row of rectangular cylinders with aspect ratio 1.5. Ocean Engineering, 119, 1–15. doi: https://doi.org/10.1016/j.oceaneng.2016.04.022

    Parthasarathy, N., Dhiman, A., Sarkar, S. (2017). Flow and heat transfer over a row of multiple semi-circular cylinders: selection of optimum number of cylinders and effects of gap ratios. The European Physical Journal Plus, 132 (12). doi: https://doi.org/10.1140/epjp/i2017-11791-2

    Razzaghpanah, Z., Sarunac, N., Javanshir, A., Khalesi, J. (2019). Natural convection heat transfer from a horizontal row of finite number of heated circular cylinders immersed in molten solar salt. Journal of Energy Storage, 22, 176–187. doi: https://doi.org/10.1016/j.est.2019.02.008

    Lima E Silva, A. L. F., Lima E Silva, S. M. M. (2014). Convection heat transfer around a single row of cylinders. Computational Thermal Sciences: An International Journal, 6 (6), 477–492. doi: https://doi.org/10.1615/computthermalscien.2014010552

    Sukhotskii, A. B., Sidorik, G. S. (2017). Experimental study of heat transfer of a single-row bundle of finned tubes in mixed convection of air. ENERGETIKA. Proceedings of CIS higher education institutions and power engineering associations, 60 (4), 352–366. doi: https://doi.org/10.21122/1029-7448-2017-60-4-352-366

    Vicente, P. G., Garcı́a, A., Viedma, A. (2002). Heat transfer and pressure drop for low Reynolds turbulent flow in helically dimpled tubes. International Journal of Heat and Mass Transfer, 45 (3), 543–553. doi: https://doi.org/10.1016/s0017-9310(01)00170-3

    Isachenko, V. P., Osipova, V. A., Sukomel, A. S. (1975). Teploperedacha. Moscow: Energiya, 488.

    Kovalenko, G. V., Halatov, A. A. (2008). Adaptation of the ice calorimeters for investigation of the heat transfer of surfaces formed by dimples. Promyshlennaya teplotehnika, 30 (2), 5–12.

    Lavrenova, D. L., Khlystov, V. M. (2016). Osnovy metrolohiyi ta elektrychnykh vymiriuvan. Kyiv, 123.

    Khalatov, A. A., Kovalenko, G. V., Meiris, A. Z. (2018). Heat Transfer in Air Flow Across a Single-Row Bundle of Tubes With Spiral Grooves. Journal of Engineering Physics and Thermophysics, 91 (1), 64–71. doi: https://doi.org/10.1007/s10891-018-1719-x

    Muliarchuk, M. A., Khalatov, A. A., Kovalenko, H. V. (2019). Hidrodynamika ta teploviddacha odnoriadnoho puchka tsylindriv z hvyntovymy kanavkamy na zovnishniy poverkhni pry poperechnomu obtikanni povitriam. XVII Vseukrainska naukovo-praktychna konferentsiya studentiv, aspirantiv ta molodykh vchenykh «Teoretychni i prykladni problemy fizyky, matematyky ta informatyky». Kyiv: KPI im. Ihoria Sikorskoho, 82–85.

    Uong, H. (1979). Osnovnye formuly i dannye po teploobmenu dlya inzhenerov. Moscow: Nauka, 216.

Downloads

Published

2020-06-30 — Updated on 2023-01-27

Versions

How to Cite

Khalatov, A., Kovalenko, G., & Muliarchuk, M. (2023). Research of hydrodynamics and heat transfer during the transverse air flow of a row of cylinders with screw grooves. Eastern-European Journal of Enterprise Technologies, 3(8 (105), 39–45. https://doi.org/10.15587/1729-4061.2020.205656 (Original work published June 30, 2020)

Issue

Vol. 3 No. 8 (105) (2020): Energy-saving technologies and equipment

Section

Energy-saving technologies and equipment

License

Copyright (c) 2020 Artem Khalatov, Glib Kovalenko, Mariia Muliarchuk

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.