Establishing patterns in determining the dynamics and strength of a covered freight car, which exhausted its resource

Authors

DOI:

https://doi.org/10.15587/1729-4061.2020.217162

Keywords:

operating resource, residual resource, resource prolongation, technical condition, structural strength, strained state

Abstract

This paper substantiates prolonging the service life of a covered railroad freight car that has exhausted its rated life of operation. In this case, the actual amount of wear of the bearing structure elements, registered during operation, have been taken into consideration. The reported calculations showed that the design service life of the bearing structure of a covered freight car when taking into consideration the extension of operation, is not less than 2 years.

Mathematical modeling was carried out to determine the dynamic load on the bearing structure of a covered freight car. It has been established that the maximum accelerations that act on the bearing structure of a covered freight car are 42 m/s2. In order to determine the acceleration distribution fields relative to the bearing structure of a covered freight car, a computer simulation was performed. The calculations showed that the maximum acceleration amounts to 43.2 m/s2 and is concentrated in the middle part of the girder beam. F-criterion was used to verify the dynamic load models.

The maximum equivalent stresses of the bearing structure of a covered freight car were determined taking into consideration the wear of its components. It was found that the maximum equivalent stresses occur in the area of interaction between the girder beam and the rod beam and amount to 344 MPa. In other words, the maximum equivalent stresses do not exceed permissible ones.

The basic dynamic indicators for a covered freight car have been calculated. The maximum accelerations that act on the bearing structure of a covered freight car in the center of masses reached about 5 m/s2. The acceleration of the body in the regions of resting on bogies was about 6 m/s2. The travel of the car is rated «good».

This study would contribute to improving the efficiency of the transportation process, as well as the functioning of railroad transport

Author Biographies

Oleksij Fomin, State University of Infrastructure and Technologies Kyrylivska str., 9, Kyiv, Ukraine, 04071

Doctor of Technical Sciences, Professor

Department of Cars and Carriage Facilities

Alyona Lovska, Ukrainian State University of Railway Transport Feierbakha sq., 7, Kharkiv, Ukraine, 61050

PhD, Associate Professor

Department of Wagons

References

  1. Sapronova, S., Bulich, D., Tkachenko, V. (2017). Continued service life of freight wagons. Visnyk Skhidnoukrainskoho Natsionalnoho universytetu imeni Volodymyra Dalia, 3 (233), 179–182.
  2. Anofriev, V. H., Reidemeister, O. H., Kalashnyk, V. A., Kulieshov, V. P. (2016). To the issue of extending the service life of cars for transportation of pellets. Science and Transport Progress. Bulletin of Dnipropetrovsk National University of Railway Transport, 3 (63), 148–160. doi: https://doi.org/10.15802/stp2016/74749
  3. Stoilov, V., Simić, G., Purgić, S., Milković, D., Slavchev, S., Radulović, S., Maznichki, V. (2019). Comparative analysis of the results of theoretical and experimental studies of freight wagon Sdggmrss-twin. IOP Conference Series: Materials Science and Engineering, 664, 012026. doi: https://doi.org/10.1088/1757-899x/664/1/012026
  4. Šťastniak, P., Moravčík, M., Smetanka, L. (2019). Investigation of strength conditions of the new wagon prototype type Zans. MATEC Web of Conferences, 254, 02037. doi: https://doi.org/10.1051/matecconf/201925402037
  5. Okorokov, A., Fomin, O., Lovska, A., Vernigora, R., Zhuravel, I., Fomin, V. (2018). Research into a possibility to prolong the time of operation of universal open top wagon bodies that have exhausted their standard resource. Eastern-European Journal of Enterprise Technologies, 3 (7 (93)), 20–26. doi: https://doi.org/10.15587/1729-4061.2018.131309
  6. Santos, G. F. M. dos, Barbosa, R. S. (2016). Safety analysis of a railway car under the periodic excitation from the track. Cogent Engineering, 3 (1). doi: https://doi.org/10.1080/23311916.2016.1263027
  7. Buonsanti, M., Leonardi, G. (2012). Dynamic Modelling of Freight Wagon with Modified Bogies. European Journal of Scientific Research, 86 (2), 274–282. Available at: https://www.academia.edu/15732567/Dynamic_modelling_of_freight_wagon_with_modified_bogies
  8. Myamlin, S., Lingaitis, L. P., Dailydka, S., Vaičiūnas, G., Bogdevičius, M., Bureika, G. (2015). Determination of the dynamic characteristics of freight wagons with various bogie. TRANSPORT, 30 (1), 88–92. doi: https://doi.org/10.3846/16484142.2015.1020565
  9. Afanas'ev, A. V. (2008). Sovershenstvovanie metodiki otsenki tehnicheskogo sostoyaniya i raschetnogo obosnovaniya prodleniya sroka sluzhby poluvagonov. Transport Urala, 1, 49–52. Available at: http://www.engcenter.ru/press/tr_urala/tu-1-rus.pdf
  10. Bogomaz, G. I., Mehov, D. D., Pilipchenko, O. P., Chernomashentseva, Yu. G. (1992). Nagruzhennost' konteynerov-tsistern, raspolozhennyh na zheleznodorozhnoy platforme, pri udarah v avtostsepku. Dynamika ta keruvannia rukhom mekhanichnykh system, 87–95.
  11. Fomin, O., Lovska, A., Radkevych, V., Horban, A., Skliarenko, I., Gurenkova, O. (2019). The dynamic loading analysis of containers placed on a flat wagon during shunting collisions. ARPN Journal of Engineering and Applied Sciences, 14 (21), 3747–3752. Available at: https://www.researchgate.net/publication/337316337_THE_DYNAMIC_LOADING_ANALYSIS_OF_CONTAINERS_PLACED_ON_A_FLAT_WAGON_DURING_SHUNTING_COLLISIONS
  12. Alyamovskiy, A. A. (2010). COSMOSWorks. Osnovy rascheta konstruktsiy na prochnost' v srede SolidWorks. Moscow, 785.
  13. Lovska, A., Fomin, O., Píštěk, V., Kučera, P. (2019). Dynamic load computational modelling of containers placed on a flat wagon at railroad ferry transportation. Vibroengineering PROCEDIA, 29, 118–123. doi: https://doi.org/10.21595/vp.2019.21132
  14. Kondratiev, A. V., Gaidachuk, V. E., Kharchenko, M. E. (2019). Relationships Between the Ultimate Strengths of Polymer Composites in Static Bending, Compression, and Tension. Mechanics of Composite Materials, 55 (2), 259–266. doi: https://doi.org/10.1007/s11029-019-09808-x
  15. Fomin, O., Lovska, A. (2020). Improvements in passenger car body for higher stability of train ferry. Engineering Science and Technology, an International Journal, 23 (6), 1455–1465. doi: https://doi.org/10.1016/j.jestch.2020.08.010
  16. Vatulia, G. L., Lobiak, O. V., Deryzemlia, S. V., Verevicheva, M. A., Orel, Y. F. (2019). Rationalization of cross-sections of the composite reinforced concrete span structure of bridges with a monolithic reinforced concrete roadway slab. IOP Conference Series: Materials Science and Engineering, 664, 012014. doi: https://doi.org/10.1088/1757-899x/664/1/012014
  17. Vatulia, G., Komagorova, S., Pavliuchenkov, M. (2018). Optimization of the truss beam. Verification of the calculation results. MATEC Web of Conferences, 230, 02037. doi: https://doi.org/10.1051/matecconf/201823002037
  18. Ivchenko, G. I., Medvedev, Yu. I. (2014). Matematicheskaya statistika. Moscow, 352.
  19. Rudenko, V. M. (2012). Matematychna statystyka. Kyiv, 304.
  20. DSTU 7598:2014. Freight wagons. General reguirements to calculation and designing of the new and modernized 1520 mm gauge wagons (non-self-propelled) (2015). Kyiv, 162.
  21. GOST 33211-2014. Freight wagons. Requirements to structural strength and dynamic qualities (2016). Moscow, 54. Available at: http://docs.cntd.ru/document/1200121493
  22. EN 12663-2. Railway applications - structural requirements of railway vehicle bodies - Part 2: Freight wagons (2010).
  23. Domin, Yu. V., Cherniak, H. Yu. (2003). Osnovy dynamiky vahoniv. Kyiv: KUETT, 269.
  24. Fomin, O., Lovska, A., Pistek, V., Kucera, P. (2020). Research of stability of containers in the combined trains during transportation by railroad ferry. MM Science Journal, 2020 (1), 3728–3733. doi: https://doi.org/10.17973/mmsj.2020_03_2019043
  25. Dižo, J., Steišūnas, S., Blatnický, M. (2016). Simulation Analysis of the Effects of a Rail Vehicle Running with Wheel Flat. Manufacturing Technology, 16 (5), 889–896. doi: https://doi.org/10.21062/ujep/x.2016/a/1213-2489/mt/16/5/889
  26. Dižo, J., Harušinec, J., Blatnický, M. (2015). Multibody System of a Rail Vehicle Bogie with a Flexible Body. Manufacturing Technology, 15 (5), 781–788. doi: https://doi.org/10.21062/ujep/x.2015/a/1213-2489/mt/15/5/781
  27. Fomin, O., Lovska, A., Píštěk, V., Kučera, P. (2019). Dynamic load effect on the transportation safety of tank containers as part of combined trains on railway ferries. Vibroengineering PROCEDIA, 29, 124–129. doi: https://doi.org/10.21595/vp.2019.21138

Downloads

Published

2020-12-31

How to Cite

Fomin, O., & Lovska, A. (2020). Establishing patterns in determining the dynamics and strength of a covered freight car, which exhausted its resource. Eastern-European Journal of Enterprise Technologies, 6(7 (108), 21–29. https://doi.org/10.15587/1729-4061.2020.217162

Issue

Vol. 6 No. 7 (108) (2020): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2020 Oleksij Fomin, Alyona Lovska

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.