Devising quality control criteria for manufacturing control valves of the type «nozzle-flap»

Authors

DOI:

https://doi.org/10.15587/1729-4061.2021.224918

Keywords:

turboshaft engine, self-oscillations, control valve, nozzle-flap, static characteristic, flow rate factor

Abstract

This paper is a continuation of research into the causes and ways to eliminate the generation of self-oscillations in the system of automatic regulation of rotations of the free turbine in the turboshaft gas turbine engines of helicopters. The study of dynamic processes in the system of automatic regulation of free turbine’s rotations in a turboshaft GTE has shown that one of the reasons for the development of self-oscillations is the poor performance of the control valve of the type «nozzle-flap» in the rotation regulator’s hydraulic drive. At a pump-regulator plant, the criterion for the quality of control valve execution or repair implies that the geometric size of the valve parts and the flow rate of working fluid through the valve when the flap is closed meet the technical requirements. As practice shows, this is not enough. With this approach, valve defects manifest themselves only during the tests of assemblies as part of the engine. This paper proposes a method to examine the characteristics of control valves such as «nozzle-flap», as well as criteria for assessing the quality of their execution. Experimental characteristics of control valves such as «nozzle-flap» for an actual regulator of free turbine rotation frequency are given. New data on the outflow of liquid from the nozzle with a flap have been obtained. It is shown that the destruction of the stagnation zone in the nozzle tip could result in that the valve flow rate increases, which negatively affects the characteristics of the hydraulic drive and regulator in general. A technique has been proposed to improve the stability of the valve’s performance by increasing the relative length of the nozzle. It is shown that the most informative characteristic of the valve is the dependence of flow rate on the position of the flap. Based on this characteristic, it is possible to determine the criteria for rejecting valves without testing them as part of the assembly

Author Biographies

Oleksandr Lytviak, National University of Civil Defence of Ukraine

PhD, Associate Professor

Department of Automatic Security Systems and Information Technologies

Sergii Komar , Ivan Kozhedub Kharkiv National Air Force University

PhD, Associate Professor

Department of Design and Strength of Aircraft and Engines

Oleksandr Derevyanko , National University of Civil Defence of Ukraine

PhD, Associate Professor

Department of Automatic Security Systems and Information Technologies

Viacheslav Durieiev , National University of Civil Defence of Ukraine

PhD, Associate Professor

Department of Automatic Security Systems and Information Technologies

References

  1. Golnaraghi, F., Kuo, B. (2017). Automatic Control Systems. McGraw-Hill Education, 1160.
  2. Harold, J., Huston, R. (2002). Dynamics of Mechanical Systems. CRC Press, 776. doi: https://doi.org/10.1201/9781420041927
  3. Aguilar, L., Boiko, I., Fridman, L., Iriarte, R. (2015). Self-Oscillations in Dynamic Systems. Basel: Birkhäuser, 163. doi: https://doi.org/10.1007/978-3-319-23303-1
  4. Kachanov, P., Lytviak, O., Derevyanko, O., Komar, S. (2019). Development of an automated hydraulic brake control system for testing aircraft turboshaft gas turbine engines. Eastern-European Journal of Enterprise Technologies, 6 (2 (102)), 52–57. doi: https://doi.org/10.15587/1729-4061.2019.185539
  5. Lytviak, O. M., Durieiev, V. O., Maliarov, M. V., Chihrin, V. S. (2019). Eksperymentalne doslidzhennia kharakterystyk rehuliatora oborotiv vilnoi turbiny nasosa-rehuliatora typu NR-3. Materialy dopovidei mizhnarod. naukovo-prakt. konf. «Integrated Computer Technologies in Mechanical Engineering». Vol. 2. Kharkiv: Natsionalnyi aerokosmichnyi universytet im. M. Ye. Zhukovskoho «Kharkivskyi aviatsiinyi instytut», 76–79.
  6. Denisova, E. V., Nasibullaeva, E. Sh., Nasibullayev, I. Sh. (2014). Investigation method of dynamic processes in the fuel elements of automation. Mehatronika, avtomatizatsiya, upravlenie, 5, 31–36.
  7. Nasibullayev, I. Sh., Nasibullaeva, E. Sh., Denisova, E. V. (2015). The dynamics of fluid flow in the technical systems with jets. Izvestiya Ufimskogo Nauchnogo TSentra RAN, 4, 20–25.
  8. Al'tshul', A. D., Kiselev, P. G. (1965). Gidravlika i aerodinamika. Moscow: Stroyizdat, 274.
  9. Stochek, N. P., Shapiro, A. S. (1978). Gidravlika zhidkostnyh raketnyh dvigateley. Moscow: Mashinostroenie, 128.
  10. Polyahov, N. N. (2017). Aerogidrodinamika. Moscow: Lenand, 384.
  11. Petrov, A. G. (2017). Analiticheskaya gidrodinamika: Ideal'naya neszhimaemaya zhidkost'. Moscow: Lenand, 368.
  12. Lepeshkin, A. V., Mihaylin, A. A., Sheypak, A. A. (2019). Gidravlika i gidropnevmoprivod. Gidravlicheskie mashiny i gidropnevmoprivod. Moscow: Infra-M, 446.
  13. Razdolin, M. V., Surnov, D. N. (1973). Agregaty vozdushno-reaktivnyh dvigateley. Moscow: Mashinostroenie, 351.
  14. Pil'gunov, V. (2012). High precision wide-range compressed airflow meter - a fine movements meter. Science and Education of the Bauman MSTU, 8, 11–34. doi: https://doi.org/10.7463/0812.0451962
  15. Shmyrov, V., Loginov, V., Fil, S., Khaustov, A., Bondarchuk, O., Kalashnikov, A., Khmelnitskiy, G. (2020). The modernization concept of aircraft An-26 and An-140 based on the use of a hybrid power system. Eastern-European Journal of Enterprise Technologies, 5 (1 (107)), 6–17. doi: https://doi.org/10.15587/1729-4061.2020.212150
  16. Pil'gunov, V. N., Efremova, K. D. (2017). Static characteristics of the pneumatic power amplifier "nozzle-shutter". Moskovskogo gosudarstvennogo tehnicheskogo universiteta MAMI, 2 (32), 40–48.
  17. Xinbei, L., Vladimir, L., Songjing, L. (2018). Performance and Flow Field Analysis of Flapper Deflection Servo Valve. 2018 Global Fluid Power Society PhD Symposium (GFPS). doi: https://doi.org/10.1109/gfps.2018.8472394
  18. Lerner, D. L. (2013). Harakteristiki ustroystva soplo-zaslonka pri obratnom techenii. Vestnik permskogo natsional'nogo issledovatel'skogo politehnicheskogo universiteta. Aerokosmicheskaya tehnika, 35, 85–100.
  19. Li, C., Choudhury, M. A. A. S., Huang, B., Qian, F. (2014). Frequency analysis and compensation of valve stiction in cascade control loops. Journal of Process Control, 24 (11), 1747–1760. doi: https://doi.org/10.1016/j.jprocont.2014.09.009
  20. Yildirim, M. T., Kurt, B. (2018). Aircraft Gas Turbine Engine Health Monitoring System by Real Flight Data. International Journal of Aerospace Engineering, 2018, 1–12. doi: https://doi.org/10.1155/2018/9570873
  21. Savelyev, D. O., Gudim, A. S., Solovev, D. B. (2019). Stabilizing the Transients in the Objects and Systems Controlling the Compensation of Nonlinear ACS (Automatic Control System) Elements. 2019 International Science and Technology Conference “EastConf.” doi: https://doi.org/10.1109/eastconf.2019.8725324

Downloads

Published

2021-02-19

How to Cite

Lytviak, O., Komar , S., Derevyanko , O. ., & Durieiev , V. . (2021). Devising quality control criteria for manufacturing control valves of the type «nozzle-flap» . Eastern-European Journal of Enterprise Technologies, 1(1 (109), 27–34. https://doi.org/10.15587/1729-4061.2021.224918

Issue

Vol. 1 No. 1 (109) (2021): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2021 Александр Литвяк , Сергей Комар , Александр Деревянко , Вячеслав Дуреев

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.