Development in mechanical and fatigue properties of AA6061/AL2O3 nanocomposites under stirring temperature (ST)

Authors

DOI:

https://doi.org/10.15587/1729-4061.2021.238588

Keywords:

6061 aluminum alloy, Al2O3 nanoparticles, nanocomposites, stirring temperatures, stir casting method, mechanical and fatigue properties

Abstract

Aluminum is expected to remain the core material for many critical applications such as aircraft and automobiles. This is due to the high resistance to different environmental conditions, desired and manageable mechanical properties, as well as high fatigue resistance. Aluminum nanocomposites such as AA6061/Al2O3 can be made in many ways using a liquid metallurgy method. The main challenges for this method in the production of nanocomposites are the difficulties of achieving a uniform distribution of reinforcing materials and possible chemical reactions between the reinforcing material and the matrix. For structural applications exclusive to aerospace sectors. The growing cost-effective nanocomposites mass production technology with essential operational and geometric flexibility is a big challenge all the time. Each method of preparing AA6061/Al2O3 nanocomposites can provide different mechanical properties. In the present study, nine nanocomposites were prepared at three stirring temperatures (800, 850, and 900 °C) with the level of Al2O3 addition of 0, 5, 7, and 9 wt %. The results of tensile, hardness and fatigue tests revealed that the composite including 9 wt % Al2O3 with 850 °C stirring temperatures has the best properties. It was also revealed that the 850 °C stirring temperature (ST) with 9 wt % Al2O3 composite provide an increase in tensile strength, VHN and reduction in ductility by 20 %, 16 % and 36.8 % respectively, compared to zero-nano. Also, the fatigue life at the 90 MPa stress level increased by 17.4 % in comparison with 9 wt % nanocomposite at 800 °C (ST). Uniform distributions were observed for all nine microstructure compositions.

Supporting Agency

  • The authors acknowledge the Iraqi Ministry of Higher Education and Scientific Research for their support of this research.

Author Biographies

Raad Mohammed Abed, Ministry of Higher Education and Scientific Research

Doctor of Mechanical Engineering

Department of Studies Engineering

Ali Yousuf Khenyab, Al- Salam University

Doctor of Mechanical Engineering

Department of Mechanical Engineering

Hussain Jasim M. Alalkawi, University of Technology

Doctor of Mechanical Engineering

Department of Mechanical Engineering

References

  1. Mohanty, P., Mahapatra, R., Padhi, P., Ramana, C. V. V., Mishra, D. K. (2020). Ultrasonic cavitation: An approach to synthesize uniformly dispersed metal matrix nanocomposites – A review. Nano-Structures & Nano-Objects, 23, 100475. doi: https://doi.org/10.1016/j.nanoso.2020.100475
  2. Singh, L., Singh, B., Saxena, K. K. (2020). Manufacturing techniques for metal matrix composites (MMC): an overview. Advances in Materials and Processing Technologies, 6 (2), 441–457. doi: https://doi.org/10.1080/2374068x.2020.1729603
  3. El-Mahallawi, I., Shash, A., Amer, A. (2015). Nanoreinforced Cast Al-Si Alloys with Al2O3, TiO2 and ZrO2 Nanoparticles. Metals, 5 (2), 802–821. doi: https://doi.org/10.3390/met5020802
  4. Iqbal, A., Nuruzzaman, D. M. (2016). Effect of the reinforcement on the mechanical properties of aluminium matrix composite: A review. International journal of applied Engineering research, 11 (21), 10408–10413.
  5. Alalkawi, H. J. M., Hamdany, A. A., Alasadi, A. A. (2017). Influence of Nanoreinforced Particles (Al2O3) on Fatigue Life and Strength of Aluminium Based Metal Matrix Composite. Al-Khwarizmi Engineering Journal, 13 (3), 91–99. doi: https://doi.org/10.22153/kej.2017.03.005
  6. Liu, Z., Mao, W., Zhao, Z. (2006). Effect of pouring temperature on semi-solid slurry of A356 Al alloy prepared by weak electromagnetic stirring. Transactions of Nonferrous Metals Society of China, 16 (1), 71–76. doi: https://doi.org/10.1016/s1003-6326(06)60013-7
  7. Haque, S., Ansari, A. H., Bharti, P. K. (2014). Effect Of Pouring Temperature And Stirring Speed On Mechanical, Microstructure And Machining Properties Of Al6061-Cu Reinforced Sicp Metal Matrix Composites. International Journal of Research in Engineering and Technology, 03 (10), 104–109. doi: https://doi.org/10.15623/ijret.2014.0322022
  8. Haque, S., Ansari, A. H., Bharti, P. K. (2016). Experimental Evaluation of Process Parameters Effect on Mechanical and Machining Properties of Al6061–Cu–SiCp-Reinforced Metal Matrix Composite. Arabian Journal for Science and Engineering, 41 (11), 4303–4311. doi: https://doi.org/10.1007/s13369-016-2094-6
  9. Rajesh, N., Yohan, M. (2016). Recent Studies In Aluminium Metal Matrix Nano Composites (AMMNCs) – A Review. International Journal of Mechanical Engineering and Technology, 7 (6), 618–623.
  10. Majdi, H. S., Habeeb, L. J. (2020). Utilizing the Characteristics of Graphene Nano-Platelets to Improve the Cross-Linking Density of a Rubber Nano-Composite. Journal of Nanostructures, 10 (4), 723–735.
  11. Al-Wajidi, W., Deiab, I., Defersha, F. M., Elsayed, A. (2018). Effect of MQL on the microstructure and strength of friction stir welded 6061 Al alloy. The International Journal of Advanced Manufacturing Technology, 101 (1-4), 901–912. doi: https://doi.org/10.1007/s00170-018-2957-y
  12. Al Alkawi, H. J., Owaidand, A., Kadhim, B. (2018). Characterization of AA 6061–Alloy Composites Reinforced by Al2O3 Nano Particles Obtained by Stir Casting. Engineering and Technology Journal, 36 (7A). doi: https://doi.org/10.30684/etj.36.7a.12
  13. Al-Salihi, H. A., Mahmood, A. A., Alalkawi, H. J. (2019). Mechanical and wear behavior of AA7075 aluminum matrix composites reinforced by Al2O3 nanoparticles. Nanocomposites, 5 (3), 67–73. doi: https://doi.org/10.1080/20550324.2019.1637576
  14. Jiang, J., Xiao, G., Che, C., Wang, Y. (2018). Microstructure, Mechanical Properties and Wear Behavior of the Rheoformed 2024 Aluminum Matrix Composite Component Reinforced by Al2O3 Nanoparticles. Metals, 8 (6), 460. doi: https://doi.org/10.3390/met8060460
  15. Zhang, Z., Li, Z., Tan, Z., Zhao, H., Fan, G., Xu, Y. et. al. (2021). Bioinspired hierarchical Al2O3/Al laminated composite fabricated by flake powder metallurgy. Composites Part A: Applied Science and Manufacturing, 140, 106187. doi: https://doi.org/10.1016/j.compositesa.2020.106187
  16. Su, H., Gao, W., Feng, Z., Lu, Z. (2012). Processing, microstructure and tensile properties of nano-sized Al2O3 particle reinforced aluminum matrix composites. Materials & Design (1980-2015), 36, 590–596. doi: https://doi.org/10.1016/j.matdes.2011.11.064
  17. Kant, S., Verma, A. S. (2017). Stir casting process in particulate aluminium metal matrix composite: a review. International Journal of Mechanics and Solids, 12 (1), 61–69.
  18. Alalkawi, H. J. M., Mohammed, A. M., Majid, R. H. (2019). Influence of Stirring Speed on Mechanical Properties for Cast Nano-Particulate AA7075-Al2O3 Composites. Al-Nahrain Journal for Engineering Sciences, 22 (2), 109–116. doi: https://doi.org/10.29194/njes.22020109
  19. Al-Jaafari, M. A. A. (2021). Study the effects of different size of Al2O3 nanoparticles on 6066AA and 7005AA composites on mechanical properties. Materials Today: Proceedings, 42, 2909–2913. doi: https://doi.org/10.1016/j.matpr.2020.12.747
  20. Bharath, V., Nagaral, M., Auradi, V., Kori, S. (2014). Preparation of 6061Al-Al2O3 MMC's by stir casting and evaluation of mechanical and wear properties. Procedia Materials Science, 6, 1658–1667. doi: https://doi.org/10.1016/j.mspro.2014.07.151
  21. Sajjadi, S. A., Ezatpour, H. R., Beygi, H. (2011). Microstructure and mechanical properties of Al–Al2O3 micro and nano composites fabricated by stir casting. Materials Science and Engineering: A, 528 (29-30), 8765–8771. doi: https://doi.org/10.1016/j.msea.2011.08.052
  22. Kandpal, B. C., Kumar, J., Singh, H. (2017). Fabrication and characterisation of Al2O3/aluminium alloy 6061 composites fabricated by Stir casting. Materials Today: Proceedings, 4 (2), 2783–2792. doi: https://doi.org/10.1016/j.matpr.2017.02.157

Downloads

Published

2021-08-26

How to Cite

Abed, R. M., Khenyab, A. Y., & Alalkawi, H. J. M. (2021). Development in mechanical and fatigue properties of AA6061/AL2O3 nanocomposites under stirring temperature (ST) . Eastern-European Journal of Enterprise Technologies, 4(12(112), 47–52. https://doi.org/10.15587/1729-4061.2021.238588

Issue

Section

Materials Science