Analysis of amplitude-phase functions of the drill string as a component of automation systemAnalysis of amplitude-phase functions of the drill string as a component of automation system

Authors

DOI:

https://doi.org/10.15587/1729-4061.2018.120544

Keywords:

drilling process, amplitude-phase characteristics, drill string, energoinformational approach, automated system

Abstract

We determined amplitude-phase frequency functions of the drill string for translational motion while drilling with immersed engines. It was established that amplitude-phase characteristic of the drill string changes with increasing depth of the well. When drilling in hard rocks, it is advisable to use cushion subs in order to reduce the level of reflected wave of mechanical stresses. To eliminate the impact of the reflected wave, it is necessary to apply a bit feed drive with absolutely soft mechanical characteristics.

We performed analysis of dynamic modes of the process of drilling wells as a control object based on provisions of the synergetic theory of information. It is proposed to employ energoinformational approach to analyze processes in the system of control over well drilling. This is due to the fact that the drilling process evolves over time and functions under conditions of the a priori and current uncertainty in terms of parameters and structure of the object. Since such a system develops over time, it undergoes changes in the structure of design of the drill string. Therefore, in order to resolve tasks on control over the process of drilling, it is necessary to know how dynamic properties of the column change depending on depth.

We identified five modes of operation in the process of drilling as a complex dynamic system: equilibrium, ordered, sorted-chaotic, randomly-ordered, and chaotic. This makes it possible to solve an important applied problem of determining amplitude-phase characteristics of the drill string depending on depth of the well, and to use them for mathematical substantiation of automated control system over drilling. 

Author Biographies

Vitaliai Kropyvnytska, Ivano-Frankivsk National Technical University of Oil and Gas Karpatska str., 15, Ivano-Frankivsk, Ukraine, 76019

PhD, Associate Professor

Department of Computer Systems and Networks 

Taras Humeniuk, Ivano-Frankivsk National Technical University of Oil and Gas Karpatska str., 15, Ivano-Frankivsk, Ukraine, 76019

PhD

Department of Computer Systems and Networks 

Natalya Sabat, Ivano-Frankivsk National Technical University of Oil and Gas Karpatska str., 15, Ivano-Frankivsk, Ukraine, 76019

PhD

Department of Computer Systems and Networks

Georgiy Sementsov, Ivano-Frankivsk National Technical University of Oil and Gas Karpatska str., 15, Ivano-Frankivsk, Ukraine, 76019

Doctor of Technical Sciences, Professor

Department of automation computer-integrated technologies

References

  1. Ohorodnikov, P. I., Svitlytskyi, V. M., Hohol, V. I. (2014). Doslidzhennia zviazku mizh pozdovzhnimy i krutylnymy kolyvanniamy burylnoi kolony. Naftohazova haluz Ukrainy, 2, 6–10.
  2. Svitlytskyi, V. M., Hohol, V. I. (2013). Analiz vibratsiynoi mitsnosti burylnoi kolony. Materialy 9-oi mizhnarodnoi naukovo-praktychnoi konferentsii «Nafta i haz Ukrainy – 2013». Yaremne, 65–66.
  3. Gulyaev, V. I., Gaidachuk, V. V., Glushakova, O. V. (2011). Andronov-Hopf bifurcations in wave models of torsional vibrations of drill strings. International Applied Mechanics, 46 (11), 1275–1283. doi: 10.1007/s10778-011-0420-y
  4. Hakimi, H., Moradi, S. (2010). Drillstring vibration analysis using differential quadrature method. Journal of Petroleum Science and Engineering, 70 (3-4), 235–242. doi: 10.1016/j.petrol.2009.11.016
  5. Nandakumar, K., Wiercigroch, M. (2013). Stability analysis of a state dependent delayed, coupled two DOF model of drill-stringvibration. Journal of Sound and Vibration, 332 (10), 2575–2592. doi: 10.1016/j.jsv.2012.12.020
  6. Gulyayev, V. I., Borshch, O. I. (2011). Free vibrations of drill strings in hyper deep vertical bore-wells. Journal of Petroleum Science and Engineering, 78 (3-4), 759–764. doi: 10.1016/j.petrol.2011.09.001
  7. Khajiyeva, L., Kydyrbekuly, A., Sergaliyev, A., Umbetkulova, A. (2013). Simulation of Movement of Drill Rods at Large Deformations. Advanced Materials Research, 702, 253–258. doi: 10.4028/www.scientific.net/amr.702.253
  8. Parepa, S., Nicolae, I. (2005). Experimental researches regarding the drilling process of the mine shafts by means of surface installations. Annual of the university of mining and geology “St. Ivan Rilski”, 48, 47–52.
  9. Elmgerbi, А., Thonhauser, G. et. al. (2016). Application of Computer Programming to Estimate Volumetric Change of an Active Drilling Fluid System Cause by Elastic Deformation of an Open Borehole Section Wall. Global Journal of Computer Science and Technology, 16 (3), 14–29.
  10. Ohorodnikov, P. I., Svitlytskyi, V. M., Hohol, V. I. (2013). Deiaki pytannia ekspluatatsiynoi nadiynosti burylnoi kolony ta yii elementiv u protsesi budivnytstva sverdlovyny. Naftohazova haluz Ukrainy, 1, 9–14.
  11. Umbetkulova, A. B. (2017). Modeling of drill string nonlinear longitudinal-transverse vibrations and their analisys. Bulletin of National Academy of Sciences of the Republic of Kazakhstan, 1 (365), 255–265.
  12. Parepa, S. (2001). Experimental researches regarding the dynamics of the mine shafts drilling process. „Universitaria ROPET 2001” International Symposium. Vol. 1. Mining engineering. University of Petroşani, 105–108.
  13. Rappold, K. (1993). Drill string vibration measurements detect bit stick-slip. Oil and Gas Journal, 66–70.
  14. Carcione, J. M., Poletto, F. (2002). A telegrapher equation for electric – telemetering in drill strings. IEEE Transactions on Geoscience and Remote Sensing, 40 (5), 1047–1053. doi: 10.1109/tgrs.2002.1010892
  15. Che, D., Ehmann, K., Cao, J. (2015). Analytical Modeling of Heat Transfer in Polycrystalline Diamond Compact Cutters in Rock Turning Processes. Journal of Manufacturing Science and Engineering, 137 (3), 031005. doi: 10.1115/1.4029653
  16. Bruton, G., Crockett, R., Taylor, M. et. al. (2014). PDC Bit Technology for the 21st Century. Oilfield Review, 26 (2), 48–57.
  17. Chen, Y., Liu, Z. Y., Duan, L. C. (2012). Simulation on Hydraulic Performance of Two Kinds of Coring Diamond Bits with Different Crown. Advanced Materials Research, 497, 350–355. doi: 10.4028/www.scientific.net/amr.497.350
  18. Zhang, Y., Liu, Y., Xu, Y., Ren, J. (2011). Drilling characteristics of combinations of different high pressure jet nozzles. Journal of Hydrodynamics, Ser. B, 23 (3), 384–390. doi: 10.1016/s1001-6058(10)60127-8
  19. Yang, X., Li, X., Lu, Y. (2011). Temperature analysis of drill bit in rock drilling. Journal of Central South University (Science and Technology), 10, 46–56.
  20. Mingxin, H., Yu, W., Baolin, L., Mingshuai, G., Liguang, W. (2014). Development of Downhole Motor Drilling Test Platform. Procedia Engineering, 73, 71–77. doi: 10.1016/j.proeng.2014.06.172
  21. Fernandez, M., Ibanez, D., Storey, D. (2005). Significant Results in Field Trials (Argentina) of an Electronically Controlled Automatic Drilling System. Proceedings of SPE Latin American and Caribbean Petroleum Engineering Conference. doi: 10.2523/94889-ms
  22. Boyadjieff, G., Murray, D., Orr, A., Porche, M., Thompson, P. (2003). Design Considerations and Field Performance of an Advanced Automatic Driller. SPE/IADC Drilling Conference. doi: 10.2118/79827-ms
  23. Branch, A. J., Andersen, K., Lavillonniere, J. L., Larsen, T., Kremer, Y., Capacho, G. A. (2001). Real-time Well Construction Monitoring – A Case History of Sincor's Heavy Oil Project. Proceedings of SPE/IADC Drilling Conference. doi: 10.2523/67757-ms
  24. Ohorodnikov, P. I., Svitlytskyi, V. M., Hohol, V. I. (2013). Analiz vibratsiynoi mitsnosti burylnoi kolony z vykorystanniam teoriy vypadkovykh kolyvan. Naftohazova haluz Ukrainy, 2, 13–18.
  25. Md Zin Che, L., Sering, L., Bakar, A. A., Sundal, E., Daudey, J. (2000). Real-Time Data Analysis While Drilling Provides Risk Management for Both Geological and Geometric Uncertainties in the Sotong K2.0 Reservoir. SPE Asia Pacific Oil and Gas Conference and Exhibition. doi: 10.2118/64477-ms
  26. Vyatkin, V. B. (2009). Sinergeticheskaya teoriya informatsii. Ch. 2. Otrazhenie diskretnyh sistem v ploskosti priznakov ih opisaniya. Nauchniy zhurnal KubTAU. 2009. Issue 45.
  27. Oganov, G. S., Shirin-Zade, S. A., Paramonov, A. A. (2009). Dinamicheskiy analiz protsessa uglubleniya skvazhin. Vestnik Assotsiatsii burovyh podryadnikov, 1, 40–44.

Downloads

Published

2018-01-11

How to Cite

Kropyvnytska, V., Humeniuk, T., Sabat, N., & Sementsov, G. (2018). Analysis of amplitude-phase functions of the drill string as a component of automation systemAnalysis of amplitude-phase functions of the drill string as a component of automation system. Eastern-European Journal of Enterprise Technologies, 1(2 (91), 48–58. https://doi.org/10.15587/1729-4061.2018.120544