The influence of the blade feather constructional inhomogeneity on the turbine cooling blades stress-strain state

Authors

DOI:

https://doi.org/10.15587/1729-4061.2018.125937

Keywords:

turbine engine blades, geometric parameters, three-dimensional finite elements, dynamic stresses

Abstract

The problem of gas turbine engines inhomogeneous rotor blades stress-strain state has been studied. For this purpose, the new, more correct mathematical model, based on the special three-dimensional curvilinear finite elements has been used. Such elements have three modifications, applied for the blade feather and its transition zones correct modeling. The complex influence of vibration and heat loads on the blade feather has also been taken into consideration.

The values of maximum dynamic stresses and their localization zones have also been found. The main concentrators of stresses are located in the transfer zones between the cooling channels and blade feather surfaces. The blade output edge is another zone of maximum dynamic stresses localization.

It has also been found that the influence of the geometric parameters of cooling channels in the blade feather cavity on the value of maximum dynamic stresses is sharper than the influence of cooling holes on the blade output edge.

By comparing the obtained calculated results with the experimental data, we can state the high adequacy and reliability of the developed mathematical model. All calculations and experimental procedures were held by equal boundary conditions. The results of the research can be used as a base for further studying of the whole rotor stress-strain state and processes of blades fatigue destruction.

Author Biography

Serhii Morhun, Admiral Makarov National University of Shipbuilding Heroiv Ukrainy аve. 9, Mykolaiv, Ukraine, 54025

PhD

Department of engineering mechanics and technology of machine building

References

  1. Samaras, C. (2009). Emissions and lifetime estimation modeling of industrial gas turbines. M. Sc. Progress Review, Cranfield University, UK, 30–35.
  2. Sukhvinder, K. B., Shyamala Kumari, M. L., Neelapu, M. L., Kedarinath, C. (2006). Transient state stress analysis on an axial flow gas turbine blades and disk using finite element procedure. Proceedings of the 4th WSEAS Int. Conf. on Heat Transfer, Thermal Engineering and Enviroment. Elounda, Greece, 323–330.
  3. Krishnakanth, P. V., Narasa Raju, G. et. al. (2013). Structural and Thermal Analysis of Gas Turbine Blade by using FEM. International Journal of Scientific Research Engineering and Technology, 2 (2), 060–065.
  4. Mrinaline, M. (2016). Steady state structural analysis of single crystal turbine blade. International Journal of Engineering Research and Technology, V5 (10), 382–384. doi: 10.17577/ijertv5is100314
  5. Ugargol, R., Narayanaswamy, K. S., Sesha Kumar, C. V. (2017). Life estimation of turbine blisk for a gas turbine engine. International Journal of Mechanical Engineering and Technology, 8 (8), 393–399.
  6. Rzadkowski, R., Gnesin, V., Kolodyazhnaya, L., Kubitz, L. (2014). Unsteady forces acting on the rotor blades in the turbine stage in 3D viscous flow in nominal and off-design regimes. Journal of Vibration Engineering, and Technologies, 2 (2), 89–95.
  7. Baqersad, J., Niezrecki, C., Avitabile, P. (2014). Predicting full-field dynamic strain on a three-bladed wind turbine using three dimensional point tracking and expansion techniques. Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems 2014. doi: 10.1117/12.2046106
  8. Postnov, V. V., Starovoitov, S. V., Fomin, S. Y., Basharov, R. R. (2014). Theoretical and experimental stress-strain analysis of machining gas turbine engine parts made of the high energy structural efficiency alloy. Journal of Engineering Science and Technology Review, 7 (5), 47–50.
  9. Bitkina, O., Kang, K.-W., Lee, J.-H. (2015). Experimental and theoretical analysis of the stress–strain state of anisotropic multilayer composite panels for wind turbine blade. Renewable Energy, 79, 219–226. doi: 10.1016/j.renene.2014.11.004
  10. Kostyuk, A. G. (1982). Dinamika i prochnost' turbomashin. Moscow: Mashinostroenie, 264.
  11. Sosunov, V. A., Chepkin, V. M. (2003). Teoriya, raschet i proektirovanie aviacionnyh dvigateley i energeticheskih ustanovok. Moscow: Mosk. energ. in-t., 677.
  12. Vorob'ev, Yu. S. (1988). Kolebaniya lopatochnogo apparata turbomashin. Kyiv: Naukova dumka, 224.
  13. Pyhalov, A. A., Milov, A. E. (2007). Staticheskiy i dinamicheskiy analiz sbornyh rotorov turbomashin. Irkutsk: Izd-vo Irkut. tekhn. un-ta, 194.
  14. Morgun, S. (2016). The blades constructions finite elements models development. Bulletin of the National Technical University «KhPI». Series: New Solutions in Modern Technologies, 42 (1214), 86–91. doi: 10.20998/2413-4295.2016.42.14
  15. Abramovich, G. N. (1991). Prikladnaya gazovaya dinamika. Moscow: Nauka, 600.
  16. Samarskiy, A. A., Vabicevich, P. N. (2009). Vychislitel'naya teploperedacha. Moscow: Editorial, 784.
  17. Kairov, A. S., Morgun, S. A. (2013). Eksperimental'noe issledovanie peremennyh vibronapryazheniy v rabochih lopatkah turbomashin. Prohresyvni tekhnolohiyi i systemy mashynobuduvannia, 1 (45)-2 (46), 131–138.

Downloads

Published

2018-03-13

How to Cite

Morhun, S. (2018). The influence of the blade feather constructional inhomogeneity on the turbine cooling blades stress-strain state. Eastern-European Journal of Enterprise Technologies, 2(7 (92), 11–17. https://doi.org/10.15587/1729-4061.2018.125937

Issue

Vol. 2 No. 7 (92) (2018): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2018 Serhii Morhun

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.