Method for determining the thickness of a binder layer at its non-uniform mass transfer inside the channel of a honeycomb filler made from polymeric paper

Authors

DOI:

https://doi.org/10.15587/1729-4061.2018.150387

Keywords:

honeycomb filler, physical-mechanical characteristics, polymeric paper, non-uniform heat and mass transfer, binder, hydrodynamic motion, uniformity of impregnation

Abstract

Sandwich panels with honeycomb filler based on polymer paper "Nomex" is widely used in crucial structures for various purposes. In the process of manufacturing such panels, some factors of the technological process, such as the application of the binder on a honeycomb filler, the temperature modes of drying and polymerization of the applied layer, most significantly affect physical-mechanical characteristics of finished products. A specific factor of production of a honeycomb filler from polymer paper is its multi-stage impregnation with the dressing composition, and then by the binder during the final operations with subsequent drying and heat treatment of the honeycomb units. These operations result into non-uniform heat and mass transfer (migration) of the binder from the central part of the panel to its peripheral end areas. The regularities of this non-uniform heat and mass transfer of the binder along the length of a honeycomb channel were explored. It was shown that these phenomena are conditioned by hydrodynamic motion of the binder, caused by temperature gradient, its density and surface tension coefficient. Based on this, we designed the method for determining the thickness of the binder layer along honeycomb channels at the known (assigned) law of the change in density and surface tension along the length of the cell of a honeycomb filler. The method makes it possible to reduce the non-uniformity of mass transfer by technological means, ensuring the necessary tolerance for physical-mechanical characteristics of honeycomb fillers from polymer paper. The problem of mass transfer enabled deeper revealing the mechanisms of the formation of the non-uniform impregnation layer at the stages of the drying process during the production of a honeycomb filler from polymer paper. Using the obtained mechanisms and technological possibilities of the regulation of characteristics of binders, it is possible to improve the non-uniformity of the layer thickness along the honeycomb channels to the values that ensure the necessary tolerance for physical-mechanical characteristics of a honeycomb filler

Author Biographies

Andrii Kondratiev, National Aerospace University Kharkiv Aviation Institute Chkalova str., 17, Kharkiv, Ukraine, 61070

Doctor of Technical Sciences, Associate Professor, Head of Department

Department of Rocket Design and Engineering

Michael Slivinsky, National Aerospace University Kharkiv Aviation Institute Chkalova str., 17, Kharkiv, Ukraine, 61070

PhD, Researcher

Problem Research Laboratory of Composite Materials

References

  1. Astrom, B. T.; Virson, J. R. (Ed.) (1999). Sandwich Manufacturing: Past, Present and Future. Stockholm, 198.
  2. Panin, V. F., Gladkov, Yu. A. (1991). Konstrukcii s zapolnitelem. Moscow: Mashinostroenie, 272.
  3. Endogur, A. I., Vaynberg, M. V., Ierusalimskiy, K. M. (1986). Sotovye konstrukcii. Vybor parametrov i proektirovanie. Moscow: Mashinostroenie, 200.
  4. Nunes, J. P., Silva, J. F. (2016). Sandwiched composites in aerospace engineering. Advanced Composite Materials for Aerospace Engineering, 129–174. doi: https://doi.org/10.1016/b978-0-08-100037-3.00005-5
  5. Foo, C. C., Chai, G. B., Seah, L. K. (2007). Mechanical properties of Nomex material and Nomex honeycomb structure. Composite Structures, 80 (4), 588–594. doi: https://doi.org/10.1016/j.compstruct.2006.07.010
  6. Roy, R., Park, S.-J., Kweon, J.-H., Choi, J.-H. (2014). Characterization of Nomex honeycomb core constituent material mechanical properties. Composite Structures, 117, 255–266. doi: https://doi.org/10.1016/j.compstruct.2014.06.033
  7. Gaydachuk, A. V., Karpikova, O. A., Kondrat'ev, A. V., Slivinskiy, M. V.; Gaydachuk, A. V. (Ed.) (2012). Sotovye zapolniteli i panel'nye konstrukcii kosmicheskogo naznacheniya. Vol. 1. Tekhnologicheskie nesovershenstva sotovyh zapolniteley i konstrukciy. Kharkiv, 279.
  8. Wang, D.-M., Wang, Z.-W. (2008). Experimental investigation into the cushioning properties of honeycomb paperboard. Packaging Technology and Science, 21 (6), 309–316. doi: https://doi.org/10.1002/pts.808
  9. Gaydachuk, V., Koloskova, G. (2016). Mathematical modeling of strength of honeycomb panel for packing and packaging with regard to deviations in the filler parameters. Eastern-European Journal of Enterprise Technologies, 6 (1 (84)), 37–43. doi: https://doi.org/10.15587/1729-4061.2016.85853
  10. Slyvyns’kyy, V., Gajdachuk, A., Melnikov, S. M. et. al. (2007). Technological possibilities for increasing quality of honeycomb cores used in aerospace engineering. 58th International Astronautical Congress 2007 Hyderabad.
  11. Kondratiev, A., Prontsevych, О. (2018). Stabilization of physical-mechanical characteristics of honeycomb filler based on the adjustment of technological techniques for its fabrication. Eastern-European Journal of Enterprise Technologies, 5 (1 (95)), 71–77. doi: https://doi.org/10.15587/1729-4061.2018.143674
  12. Gaidachuc, A., Guriev, H., Ostrovsky, E., Slivinsky, M. (2005). A polar-sensitive charges interaction in dielectrics process modulation during making honeycomb aggregate out of polymeric paper. Aerospace technic and technology, 3 (19), 5–12.
  13. Gaydachuk, A. V., Slivinskiy, M. V., Ostrovskiy, E. K. (2006). Issledovanie massoperenosa komponentov svyazuyushchego pri izgotovlenii sotovyh zapolniteley iz polimernoy bumagi "Nomex". Aerospace technic and technology, 4 (30), 5–10.
  14. Gaydachuk, A. V., Slivinskiy, M. V., Ostrovskiy, E. K. (2007). Formirovanie sloya svyazuyushchego na poverhnosti polimernoy bumagi v processe propitki sotovyh zapolniteley. Aerospace technic and technology, 3 (39), 34–41.
  15. Landau, L. D., Lifshic, E. M. (1986). Teoreticheskaya fizika. Vol. 6. Moscow: Nauka, 736.
  16. Yue, J., Chen, G., Yuan, Q., Luo, L., Gonthier, Y. (2007). Hydrodynamics and mass transfer characteristics in gas–liquid flow through a rectangular microchannel. Chemical Engineering Science, 62 (7), 2096–2108. doi: https://doi.org/10.1016/j.ces.2006.12.057
  17. Vygodskiy, M. Ya. (2006). Spravochnik po vysshey matematike. Moscow, 991.

Downloads

Published

2018-12-10

How to Cite

Kondratiev, A., & Slivinsky, M. (2018). Method for determining the thickness of a binder layer at its non-uniform mass transfer inside the channel of a honeycomb filler made from polymeric paper. Eastern-European Journal of Enterprise Technologies, 6(5 (96), 42–48. https://doi.org/10.15587/1729-4061.2018.150387

Issue

Vol. 6 No. 5 (96) (2018): Applied physics

Section

Applied physics

License

Copyright (c) 2018 Andrii Kondratiev, Michael Slivinsky

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.