Flow visualization of water jet passing through the empty space of crossflow turbine runner
DOI:
https://doi.org/10.15587/1729-4061.2019.154896Keywords:
nozzle entry arc, flow condition, performance characteristic of cross-flow turbine.Abstract
Hydropower plants are a form of renewable energy resources, which comes from flowing water. The turbine is used to drive the generator then convert mechanical energy into electrical energy. The turbine wheel is located inside the turbine housing and the turbine wheel rotates the power shaft. One of the most used turbines is a cross-flow turbine. The pattern of water jet flowing throughout the empty space of the runner of the cross-flow turbine is influenced by the number of active runner blades pounded by water from the turbine nozzle. The difference in the flow patterns was believed having a relation to the performance differences of the three turbine models. The flow visualizations of water passing through the empty space of the cross-flow turbine runner were taken from the experimental study intended to investigate performance characteristics of three cross-flow turbine models designed on the same value of flow rates, runner diameters and rotational speeds; but each turbine model having different values of runner width as well as nozzle entry arc. Both of the nozzle and runner widths were designed as the function of the nozzle entry arc, therefore the shorter pair of runner-nozzle width the larger nozzle entry arc and vice versa. The flow visualizations of water passing on the turbine were studied using the empty space of the cross-flow turbine. The three models were tested on the same head and the same flow rate at the speed of 50, 100, 150, 250, 300 and 500 rpm. The photos of water flowing through the empty space in the turbine model runners were taken to find out the conditions of flow and the efficiency of the models was calculated to show the performance of the turbine. Images are taken within 10 cm and parallel to the turbine. The cross-flow turbine models were designed with 197 mm runner diameter of each and have the ratio of runner diameter to runner length of 1:2. One side of each turbine model end disk was made from transparent media named perspex facilitating the researcher to observe the water flow condition during flowing through inside the runner. The conditions of the flow of water passing through the empty space of turbine wheels were photographed using a Nikon camera equipped with a hallogen lamp having a power of 1000 watts to capture the difference of flow pattern among the three models of the turbine. The nozzle entry arcs used in this experimental study were 75o, 90o and 120o. In addition, the nozzle of each model has the same cross-sectional area and the roof of each was designed having roof curvature radius centered on the shaft axis. Such nozzle roof curvature was expected to be able to deliver water in the better direction as well as its flow condition as the water enters the turbine runner. The magnitude of the nozzle entry arc determines the number of active vanes pounded by the jet of water coming out of the nozzle, these conditions affect the pattern of water flow at the moment of passing through the empty space of the turbine wheel and then this flow pattern was believed to affect the performance characteristic of the cross-flow turbine. One side of each runner disk was made from Perspex, for the researcher to be able to observe the water flow condition during flowing through inside the runner.
Supporting Agency
- Brawijaya University
References
- Government Gazette Republic of Namibia. Available at: https://namiblii.org/system/files/gazette/2018/6670/%236670-Gov%20N163.pdf
- England, J. F., Cohn, T. A., Faber, B. A., Stedinger, J. R., Thomas, W. O., Veilleux, A. G. et. al. (2018). Guidelines for determining flood flow frequency – Bulletin 17C. Techniques and Methods. doi: https://doi.org/10.3133/tm4b5
- Thin Layer Chromatography (2019). Chemistry LibreTexts. Available at: https://chem.libretexts.org/Ancillary_Materials/Demos%2C_Techniques%2C_and_Experiments/General_Lab_Techniques/Thin_Layer_Chromatography
- Childress, S. (2010). Walking on water. Journal of Fluid Mechanics, 644, 1. doi: https://doi.org/10.1017/s0022112009993107
- Owusu-Boateng, G., Adjei, V. (2014). The potential utilization of grey water for irrigation: A case study on the Kwame Nkrumah University of Science and Technology, Kumasi Campus. Journal of Applied Research in Water and Wastewater, 1 (1), 31–37.
- Wacławczyk, T., Koronowicz, T. (2008). Comparison of cicsam and hric high-resolution schemes for interface capturing. Journal of Theoretical and Applied Mechanics, 46 (2), 325–345.
- Colonna, P., Harinck, J., Rebay, S., Guardone, A. (2008). Real-Gas Effects in Organic Rankine Cycle Turbine Nozzles. Journal of Propulsion and Power, 24 (2), 282–294. doi: https://doi.org/10.2514/1.29718
- Pasquale, D., Ghidoni, A., Rebay, S. (2013). Shape Optimization of an Organic Rankine Cycle Radial Turbine Nozzle. Journal of Engineering for Gas Turbines and Power, 135 (4), 042308. doi: https://doi.org/10.1115/1.4023118
- Mazur, Z., Hernandez-Rossette, A., Garcia-Illescas, R., Luna-Ramirez, A. (2008). Failure analysis of a gas turbine nozzle. Engineering Failure Analysis, 15 (7), 913–921. doi: https://doi.org/10.1016/j.engfailanal.2007.10.009
- Nuyttens, D., Baetens, K., De Schampheleire, M., Sonck, B. (2007). Effect of nozzle type, size and pressure on spray droplet characteristics. Biosystems Engineering, 97 (3), 333–345. doi: https://doi.org/10.1016/j.biosystemseng.2007.03.001
- Hagena, O. F., Obert, W. (1972). Cluster Formation in Expanding Supersonic Jets: Effect of Pressure, Temperature, Nozzle Size, and Test Gas. The Journal of Chemical Physics, 56 (5), 1793–1802. doi: https://doi.org/10.1063/1.1677455
- Chang, R., Nam, J., Sun, W. (2008). Effects of Dispensing Pressure and Nozzle Diameter on Cell Survival from Solid Freeform Fabrication–Based Direct Cell Writing. Tissue Engineering Part A, 14 (1), 41–48. doi: https://doi.org/10.1089/ten.a.2007.0004
- Grisso, R., Hipkins, P., Askew, S. D., Hipkins, L., Mccall, D. (2013). Nozzles: Selection and sizing. College of Agriculture and Life Sciences, Virginia Polytechnic Institute and State University. Available at: https://www.pubs.ext.vt.edu/content/dam/pubs_ext_vt_edu/442/442-032/442-032_pdf.pdf
- Kanoğlu, M. (2001). Cryogenic turbine efficiencies. Exergy, An International Journal, 1 (3), 202–208. doi: https://doi.org/10.1016/s1164-0235(01)00026-7
- Poullikkas, A. (2005). An overview of current and future sustainable gas turbine technologies. Renewable and Sustainable Energy Reviews, 9 (5), 409–443. doi: https://doi.org/10.1016/j.rser.2004.05.009
- Kacker, S. C., Okapuu, U. (1982). A Mean Line Prediction Method for Axial Flow Turbine Efficiency. Journal of Engineering for Power, 104 (1), 111. doi: https://doi.org/10.1115/1.3227240
- Safarian, S., Aramoun, F. (2015). Energy and exergy assessments of modified Organic Rankine Cycles (ORCs). Energy Reports, 1, 1–7. doi: https://doi.org/10.1016/j.egyr.2014.10.003
- Vennell, R. (2012). Realizing the potential of tidal currents and the efficiency of turbine farms in a channel. Renewable Energy, 47, 95–102. doi: https://doi.org/10.1016/j.renene.2012.03.036
- Garrett, C., Cummins, P. (2007). The efficiency of a turbine in a tidal channel. Journal of Fluid Mechanics, 588. doi: https://doi.org/10.1017/s0022112007007781
- Tiwari, A. K., Hasan, M. M., Islam, M. (2013). Effect of ambient temperature on the performance of a combined cycle power plant. Transactions of the Canadian Society for Mechanical Engineering, 37 (4), 1177–1188. doi: https://doi.org/10.1139/tcsme-2013-0099
- Gorban’, A. N., Gorlov, A. M., Silantyev, V. M. (2001). Limits of the Turbine Efficiency for Free Fluid Flow. Journal of Energy Resources Technology, 123 (4), 311. doi: https://doi.org/10.1115/1.1414137
- Barthelmie, R. J., Jensen, L. E. (2010). Evaluation of wind farm efficiency and wind turbine wakes at the Nysted offshore wind farm. Wind Energy, 13 (6), 573–586. doi: https://doi.org/10.1002/we.408
- Wind Turbine Blade Aerodynamics. Available at: http://kimerius.com/app/download/5784129509/Wind+turbine+blade+aerodynamics.pdf
- Poursaeidi, E., Aieneravaie, M., Mohammadi, M. R. (2008). Failure analysis of a second stage blade in a gas turbine engine. Engineering Failure Analysis, 15 (8), 1111–1129. doi: https://doi.org/10.1016/j.engfailanal.2007.11.020
- Mazur, Z., Garcia-Illescas, R., Aguirre-Romano, J., Perez-Rodriguez, N. (2008). Steam turbine blade failure analysis. Engineering Failure Analysis, 15 (1-2), 129–141. doi: https://doi.org/10.1016/j.engfailanal.2006.11.018
- Stout, C., Islam, S., White, A., Arnott, S., Kollovozi, E., Shaw, M. et. al. (2017). Efficiency Improvement of Vertical Axis Wind Turbines with an Upstream Deflector. Energy Procedia, 118, 141–148. doi: https://doi.org/10.1016/j.egypro.2017.07.032
- Sarkar, A., Behera, D. K. (2012). Wind Turbine Blade Efficiency and Power Calculation with Electrical Analogy. International Journal of Scientific and Research Publications, 2 (2).
- Padture, N. P. (2002). Thermal Barrier Coatings for Gas-Turbine Engine Applications. Science, 296 (5566), 280–284. doi: https://doi.org/10.1126/science.1068609
- Wang, C.-C., Chow, H.-M., Yang, L.-D., Lu, C.-T. (2009). Recast layer removal after electrical discharge machining via Taguchi analysis: A feasibility study. Journal of Materials Processing Technology, 209 (8), 4134–4140. doi: https://doi.org/10.1016/j.jmatprotec.2008.10.012
- Liu, C., Jiang, D. (2014). Crack modeling of rotating blades with cracked hexahedral finite element method. Mechanical Systems and Signal Processing, 46 (2), 406–423. doi: https://doi.org/10.1016/j.ymssp.2014.01.007
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 Djoko Sutikno
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.