Modeling of technological providing of operating properties of surfaces of hardened largemodal gear-wheels

Authors

  • Юрий Викторович Тимофеев National Technical University "Kharkiv Polytechnic Institute", Str. Frunze, 21, Kharkov, Ukraine, 61002, Ukraine
  • Александр Александрович Клочко Donbass State Engineering Academy, Donetsk region., Kramatorsk, bul. Mashinostroiteley, 39, 84313, Ukraine
  • Алексей Николаевич Кравцов Federal State Autonomous Educational Institution of Higher Professional Education «Ural Federal University named after the first President of Russia B.N.Yeltsin», World street, 19. Ekaterinburg, Russia, 620002, Russian Federation

DOI:

https://doi.org/10.15587/1729-4061.2013.16687

Keywords:

complex parameters, technological providing, operating properties, gear-wheels, system optimization

Abstract

The system of complex parameters, which is used for technological providing of operating properties of hardened large modal gear-wheels, and the technique of two-level providing of these properties, using graphic methods of system optimization were considered. The technological parameters for providing of operational properties of evolvment surfaces of hardened largemodal gear-wheels, their systemic analysis and experimental researches results were presented.

The study has shown that for hardened gear-wheels, their parameters, such as teeth breakdown, active surfaces chipping and teeth upper layers flaking, teeth abrasion, plastic teeth deformations and scoring with the same regulated quality parameters of hardened gear-wheels surface, had the smaller dispersion of scattering than when using conventional technique of surfaces condition regulation.

Also, the introduction of modeling of technological providing of hardened gear-wheels surfaces operating properties, using the system optimization, allows the fullest use of opportunities of their treatment methods when developing technological processes

Author Biographies

Юрий Викторович Тимофеев, National Technical University "Kharkiv Polytechnic Institute", Str. Frunze, 21, Kharkov, Ukraine, 61002

Doctor of Technical Sciences, Professor

Department of Mechanical Engineering and Machine Tools

Александр Александрович Клочко, Donbass State Engineering Academy, Donetsk region., Kramatorsk, bul. Mashinostroiteley, 39, 84313

PhD, associate professor

Department metal-cutting machine-tools and instruments

Алексей Николаевич Кравцов, Federal State Autonomous Educational Institution of Higher Professional Education «Ural Federal University named after the first President of Russia B.N.Yeltsin», World street, 19. Ekaterinburg, Russia, 620002

Postgraduate student

Department technology of engineer

References

  1. Рыжов, Э. В. Технологические методы повышения износостойкости деталей машин [Текст] / Э. В. Рыжов. – Киев: Наук. Думка, 1984. – 272 с.
  2. Кравцов, Н. В. Технологические особенности обработки крупномодульных закаленных зубчатых колес [Текст] / Н. В. Кравцов, Ю. В. Тимофеев, А. А. Клочко и др.; науч. ред. А. А. Пермяков; общ. ред. Ю.М. Соломенцев //Серия: Управление качеством технологических процессов в машиностроении. – ВолГТУ – Тольятти: ЗАО «ОНИКС», 2012. – 254 с. – ISBN 59903090-6-7.
  3. Суслов, А. Г. Инженерия поверхностей деталей [Текст] / колл. авт.; под ред. А. Г. Суслова. – М.: «Машиностроение», 2008. – 320 с.
  4. Крагельский, И. В. Основы расчетов на трение и износ [Текст] / И. В. Крагельский, М. Н. Добычин, В. С. Комбалов. – М.: Машиностроение, 1977. – 525 с.
  5. Oktema, H. Application of response surface methodology in the optimization of cutting conditions for surface roughness [Text] / H. Oktema, T. Erzurumlu and H. Kurtaran // J. Mater. processing Technol, 2005. – Vol. 170. – pp. 11–16.
  6. Кравцов, А. Н. Обеспечение эксплуатационных свойств поверхностей деталей при изготовлении [Текст] / А. Н. Кравцов, Н. В. Кравцов; Закрытое акционерное об-во "ОНИКС". – Ирбит: ОНИКС, 2011. – 261 с.
  7. Thomas, T. R. Rough Surfaces [Text] / T. R. Thomas. – 2nd ed. – Imperial College Press. – London, 1999.
  8. Wyko Corporation. Surface Profiles: Technical reference manual [Text] / Wyko Corporation. – Tucson, AZ, USA. – 1996.
  9. Lou, M. S. Inprocess surface roughness recognition system in end-milling operations [Text] / M. S. Lou, J. C. Chen // International Journal of Advanced Manufacturing Technology. – 1999. – Vol.15. – pp. 200-209.
  10. Alauddin, M. Optimization of surface finish in end milling Inconel 718 [Text] / M. Alauddin, M. A. El Baradie, M. S. J. Hashmi // J. Mat. Proc. – 1996. – Vol. 56. – pp. 54–65.
  11. Ryzhov, Je. V. (1984). Tehnologicheskie metody povyshenija iznosostojkosti detalej mashin. Kiev.: Nauk. Dumka, 272 р.
  12. Kravcov, N. V., Timothy, Yu. V., Klochko, A. A. and others; In: Permyakov, A. A., Solomencev, Yu. M. (2012). Technological features of treatment of krupnomodul'nykh of hard-tempered gear-wheels. Series: A quality of technological processes management is in an engineer. VOLGTU is Tol'yatti: Joint-stock COMPANY is «ONYX». ISBN 59903090-6-7, 254 p.
  13. In: Suslov, A. G. Engineering of surfaces of details (2008). M.: «Engineer», 320 p.
  14. Kragelskiy, I. V., Dobychin, M. N., Kombalov, V. S. (1977). Osnovy calculations on a friction and wear. M.: Engineer, 525 p.
  15. Oktema, H., Erzurumlu, T., and Kurtaran, H. (2005). Application of response surface methodology in the optimization of cutting conditions for surface roughness, J. Mater. processing Technol, 170, 11–16
  16. Kravcov, A. N., Kravcov, N. V.; Closed joint-stock society "ONYX". (2011). Providing of operating properties of surfaces of details at making. Irbit: ONYX, 261 p.
  17. Thomas, T. R. (1999). Rough Surfaces, 2nd ed., Imperial College Press, London.
  18. Wyko Corporation. (1996). Surface Profiles: Technical reference manual. Wyko Corporation; Tucson, AZ, USA.
  19. Lou, M. S. & Chen, J. C. (1999). Inprocess surface roughness recognition system in end-milling operations, International Journal of Advanced Manufacturing Technology, 15, 200-209.
  20. Alauddin, M., El Baradie, M. A., Hashmi, M. S. J. (1996). Optimization of surface finish in end milling Inconel 718. J. Mat. Proc., Vol. 56, 54–65.

Downloads

Published

2013-07-30

How to Cite

Тимофеев, Ю. В., Клочко, А. А., & Кравцов, А. Н. (2013). Modeling of technological providing of operating properties of surfaces of hardened largemodal gear-wheels. Eastern-European Journal of Enterprise Technologies, 4(7(64), 49–55. https://doi.org/10.15587/1729-4061.2013.16687

Issue

Vol. 4 No. 7(64) (2013): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2014 Юрий Викторович Тимофеев, Александр Александрович Клочко, Алексей Николаевич Кравцов

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.