Improvement of functional performance of concrete in livestock buildings through the use of complex admixtures
DOI:
https://doi.org/10.15587/1729-4061.2019.179177Keywords:
livestock buildings, corrosive medium, biological corrosion of concrete, bactericidal admixtures, concrete strengthAbstract
When examining concrete in livestock buildings, signs of corrosion and destruction of concrete floors and walls were found. Experimental studies have identified main critical points that directly affected concrete continuity. Excessive moisture, use of corrosive acidic or alkaline disinfectants and presence of natural excretions of animals (urine and feces) were found in livestock buildings.
To solve this problem, admixtures were proposed: yellow iron oxide pigment and liquid glass which improve strength characteristics of concrete, its heat resistance and reduce penetrability.
It was proved by the conducted studies that introduction into concrete of admixtures in quantities from 0.5 % to 2 % has resulted in a 2.8 times smaller depth of chloride penetration as compared to the control specimens. This was due to a decrease in water absorption by concrete when introducing iron oxide, cuprous sulphate, peracetic acid and sodium silicate which reduced pore size in samples.
It was proposed as an innovation to assess thermal stability of concrete using the method of temperature-programmed desorption mass spectrometry (TPMS) based on the dependence of evolution of carbon monoxide and carbon dioxide from samples of carbonate-containing substances on the sample temperature.
Microbiological studies have identified microbes of Penicillium and Fusarium species, bacteria Escherichia coli and Pseudomonas aeruginosa, which cause corrosion of concrete in livestock buildings. Numerous experiments have shown that the proposed admixtures added to the concrete (based on yellow iron oxide pigment (1.5‒2.0 wt. %), peracetic acid (0.2‒0.3 wt. %), liquid glass (2‒3 wt. %) and cuprous sulfate (0.5‒1.0 wt. %) had antimicrobial properties and thus prospects for their use in animal husbandryReferences
- Prusty, J. K., Patro, S. K., Basarkar, S. S. (2016). Concrete using agro-waste as fine aggregate for sustainable built environment – A review. International Journal of Sustainable Built Environment, 5 (2), 312–333. doi: https://doi.org/10.1016/j.ijsbe.2016.06.003
- Petrov, A., Pavliuchenkov, M., Nanka, A., Paliy, A. (2019). Construction of an algorithm for the selection of rigid stops in steel concrete beams. Eastern-European Journal of Enterprise Technologies, 1 (7 (97)), 41–49. doi: https://doi.org/10.15587/1729-4061.2019.155469
- Okojie, L. O. (2014). Cement Production and Sustainable Rural Farming Livelihood in Nigeria: Striking a Sensible Balance Through Environmental Legislation and Enforcement. European Journal of Sustainable Development, 3 (3), 251–262. doi: https://doi.org/10.14207/ejsd.2014.v3n3p251
- Hilal, A. A. (2016). Microstructure of Concrete. High Performance Concrete Technology and Applications. doi: https://doi.org/10.5772/64574
- Justs, J., Bajare, D., Korjakins, A., Mezinskis, G., Locs, J., Bumanis, G. (2013). Microstructural Investigations of Ultra-High Performance Concrete Obtained by Pressure Application within the First 24 Hours of Hardening. Construction Science, 14, 50–57. doi: https://doi.org/10.2478/cons-2013-0008
- Johansson, S. (2011). Biological growth on rendered façades. Lund University, Division of Building Materials.
- Nnaji, C. C., Amadi, U. H., Molokwu, R. (2016). Investigative Study of Biodeterioration of External Sandcrete/Concrete Walls in Nigeria. Research Journal of Environmental Toxicology, 10 (2), 88–99. doi: https://doi.org/10.3923/rjet.2016.88.99
- Sоrbu, M. (2008). The environmental impact of the animal husbandry buildings (B). ProEnvironment, 2, 52–54.
- Ettenauer, J. D. (2010). Culture dependent and-independent identification of microorganisms on monuments. University of Vienna.
- Danilchenko, S. N., Chіvanov, V. D., Ryabishev, A. G., Novіkov, S. V. et. al. (2016). The Study of Thermal Decomposition of Natural Calcium Carbonate by the Temperature-programmed Mass Spectrometry Technique. Journal of Nano- and Electronic Physics, 8 (4 (1)), 04031-1–04031-3. doi: https://doi.org/10.21272/jnep.8(4(1)).04031
- Sanchez, F., Sobolev, K. (2010). Nanotechnology in concrete – A review. Construction and Building Materials, 24 (11), 2060–2071. doi: https://doi.org/10.1016/j.conbuildmat.2010.03.014
- Li, X., Kappler, U., Jiang, G., Bond, P. L. (2017). The Ecology of Acidophilic Microorganisms in the Corroding Concrete Sewer Environment. Frontiers in Microbiology, 8. doi: https://doi.org/10.3389/fmicb.2017.00683
- Vincke, E., Verstichel, S., Monteny, J., Vrerstraete, W. (1999). A new test procedure for biogenic sulfuric acid corrosion of concrete. Biodegradation, 10 (6), 421–428. doi: https://doi.org/10.1023/A:1008309320957
- Ramamurthy, K., Kunhanandan Nambiar, E. K., Indu Siva Ranjani, G. (2009). A classification of studies on properties of foam concrete. Cement and Concrete Composites, 31 (6), 388–396. doi: https://doi.org/10.1016/j.cemconcomp.2009.04.006
- Wei, S., Jiang, Z., Liu, H., Zhou, D., Sanchez-Silva, M. (2013). Microbiologically induced deterioration of concrete: a review. Brazilian Journal of Microbiology, 44 (4), 1001–1007. doi: https://doi.org/10.1590/s1517-83822014005000006
- Grengg, C., Mittermayr, F., Ukrainczyk, N., Koraimann, G., Kienesberger, S., Dietzel, M. (2018). Advances in concrete materials for sewer systems affected by microbial induced concrete corrosion: A review. Water Research, 134, 341–352. doi: https://doi.org/10.1016/j.watres.2018.01.043
- Ferrari, C., Santunione, G., Libbra, A., Muscio, A., Sgarbi, E., Siligardi, C., Barozzi, G. S. (2015). Review on the influence of biological deterioration on the surface properties of building materials: organisms, materials, and methods. International Journal of Design & Nature and Ecodynamics, 10 (1), 21–39. doi: https://doi.org/10.2495/dne-v10-n1-21-39
- Song, Y., Tian, Y., Li, X., Wei, J., Zhang, H., Bond, P. L. et. al. (2019). Distinct microbially induced concrete corrosion at the tidal region of reinforced concrete sewers. Water Research, 150, 392–402. doi: https://doi.org/10.1016/j.watres.2018.11.083
- Kazemian, S., Huat, B. K. B., Mohammed, A. T., Barghchi, M. (2011). The Effect of Sodium Silicate on Cement-Sodium Silicate System Grout. Modern Methods and Advances in Structural Engineering and Construction(ISEC-6). doi: https://doi.org/10.3850/978-981-08-7920-4_s2-g01-cd
- The Effect of Using Commercial Red and Black Iron Oxides as a Concrete Admixtures on its Physiochemical and Mechanical Properties. (2015). International Journal of Science and Research (IJSR), 4 (12), 1389–1393. doi: https://doi.org/10.21275/v4i12.nov152049
- Kosmatka, S. H., Wilson, M. L. et. al. (2011). Design and Control of Concrete Mixtures, EB001. Portland Cement Association, 444.
- Shekari, A. H., Razzaghi, M. S. (2011). Influence of Nano Particles on Durability and Mechanical Properties of High Performance Concrete. Procedia Engineering, 14, 3036–3041. doi: https://doi.org/10.1016/j.proeng.2011.07.382
- Loganina, V. I., Kislitsyna, S. N., Mazhitov, Y. B. (2018). Development of sol-silicate composition for decoration of building walls. Case Studies in Construction Materials, 9, e00173. doi: https://doi.org/10.1016/j.cscm.2018.e00173
- Liu, D., Behrens, S., Pedersen, L.-F., Straus, D. L., Meinelt, T. (2016). Peracetic acid is a suitable disinfectant for recirculating fish-microalgae integrated multi-trophic aquaculture systems. Aquaculture Reports, 4, 136–142. doi: https://doi.org/10.1016/j.aqrep.2016.09.002
- Gad, S. C. (2014). Peracetic Acid. Encyclopedia of Toxicology, 788–790. doi: https://doi.org/10.1016/b978-0-12-386454-3.01197-0
- Onuaguluchi, O., Eren, О. (2012). Copper tailings as a potential additive in concrete: сonsistency, strength and toxic metal immobilization properties. Indian Journal of Engineering and Materials Sciences, 19 (2), 79–86.
- DSTU B V.2.7-224:2009. Building materials. Concretes rules for the strength control. Minrehionbud Ukrainy. Kyiv, 27.
- Оtsuki, N., Nagataki, S., Nakashita, K. (1992). Evaluation of AgNo 3 solution spray method for measurement of chloride penetration into hardened cementitious matrix materials. Journal aci mater, 89 (6), 587–592. Available at: https://www.concrete.org/publications/internationalconcreteabstractsportal.aspx?m=details&ID=4036
- Kuznetsov, V. N., Yanovska, A. A., Novikov, S. V., Starikov, V. V., Kalinichenko, T. G., Kochenko, A. V. et. al. (2015). Study of Thermal Activated CO2 Extraction Processes from Carbonate Apatites Using Gas Chromatography. Jоurnal of Nano- and Electronic Physics, 7 (3), 03034.
- Metodychni vkazivky po vyznachenniu chutlyvosti mikroorhanizmiv do antymikrobnykh preparativ metodom dyfuziyi v ahar za dopomohoiu standartnykh dyskiv z antybiotykamy (zatverdzheni naukovo-metodychnoiu radoiu DKVM Ukrainy vid 20.12.2007 r.) (2010).
- Bertron, A. (2014). Understanding interactions between cementitious materials and microorganisms: a key to sustainable and safe concrete structures in various contexts. Materials and Structures, 47 (11), 1787–1806. doi: https://doi.org/10.1617/s11527-014-0433-1
- Fomina, M., Podgorsky, V. S., Olishevska, S. V., Kadoshnikov, V. M., Pisanska, I. R., Hillier, S., Gadd, G. M. (2007). Fungal Deterioration of Barrier Concrete used in Nuclear Waste Disposal. Geomicrobiology Journal, 24 (7-8), 643–653. doi: https://doi.org/10.1080/01490450701672240
- Li, X., O’Moore, L., Song, Y., Bond, P. L., Yuan, Z., Wilkie, S. et. al. (2019). The rapid chemically induced corrosion of concrete sewers at high H2S concentration. Water Research, 162, 95–104. doi: https://doi.org/10.1016/j.watres.2019.06.062
- Shkromada, O., Skliar, O., Paliy, A., Ulko, L., Gerun, I., Naumenko, O. et. al. (2019). Development of measures to improve milk quality and safety during production. Eastern-European Journal of Enterprise Technologies, 3 (11 (99)), 30–39. doi: https://doi.org/10.15587/1729-4061.2019.168762
- Goldstein, S., Meyerstein, D., Czapski, G. (1993). The Fenton reagents. Free Radical Biology and Medicine, 15 (4), 435–445. doi: https://doi.org/10.1016/0891-5849(93)90043-t
- Zhou, W., Zhao, H., Gao, J., Meng, X., Wu, S., Qin, Y. (2016). Influence of a reagents addition strategy on the Fenton oxidation of rhodamine B: control of the competitive reaction of ·OH. RSC Advances, 6 (110), 108791–108800. doi: https://doi.org/10.1039/c6ra20242j
- George, R. P., Ramya, S., Ramachandran, D., Kamachi Mudali, U. (2013). Studies on Biodegradation of normal concrete surfaces by fungus Fusarium sp. Cement and Concrete Research, 47, 8–13. doi: https://doi.org/10.1016/j.cemconres.2013.01.010
- Paliy, A., Paliy, A., Nanka, A., Chalaya, O., Chalyi, O. (2019). Establishment of the efficiency of animal breeding premises disinfection by modern disinfectants. EUREKA: Life Sciences, 4, 3–8. doi: https://doi.org/10.21303/2504-5695.2019.00959
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 Oksana Shkromada, Andriy Paliy, Oleksandr Nechyporenko, Oleksandr Naumenko, Valentyna Nechyporenko, Olexandr Burlaka, Alexander Reshetnichenko, Oleksandr Tsereniuk, Olha Shvets, Anatoliy Paliy
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.