Investigating the process of shrinkage depression formation at the combined radial-backward extrusion of parts with a flange

Authors

DOI:

https://doi.org/10.15587/1729-4061.2019.179232

Keywords:

combined extrusion, energy method, parts with a flange, defect formation, shrinkage depression, deformation process

Abstract

The possibilities of using an energy method to forecast defect formation in the form of shrinkage depression in the combined extrusion processes have been investigated. We have proposed a mathematical model of the combined radial-reverse extrusion process of hollow details with a flange, taking into consideration the degeneration of the trapezoidal module into a rectangular one. Separate stages in the deformation process have been defined, depending on the magnitude of the active tool stroke compared with the thickness of the bottom of the cup. We have devised a generalized estimation scheme for the process of combined radial-reverse extrusion of parts with a flange taking into consideration the final stage of deformation (Hbottom<h1). The magnitude of the reduced pressure of deformation has been derived as a function of the geometric, technological, and kinematic parameters of the extrusion process. A role of the kinematic parameter of the process belongs to a relative speed of metal flow in the vertical direction (filling the cup’s wall at the inverse flow of metal). The magnitude for the reduced pressure of deformation has been optimized based on this parameter. We have analyzed the character of change in the optimum magnitude of a relative speed of metal flow in the vertical direction in the course of the process. The differences have been established in the derived dependences of a given kinematic parameter for the process with the formation of shrinkage depression in the bottom part of a component and without defect formation.

It has been substantiated that the use of combined extrusion in the manufacture of hollow parts with a flange, when compared with the application of simple schemes of deformation, improves the technological capabilities of the process. We have proven that the technologies for introducing combined extrusion had not been sufficiently studied and there is a lack of recommendations on predicting the formation of a defect in the form of shrinkage depression. The estimation scheme has been proposed for the radial-reverse extrusion process, taking into consideration the emergence of shrinkage depression at the final stage of deformation. We have modeled the process of combined extrusion of hollow parts with a flange and established the influence of friction conditions on the time of the emergence of shrinkage depression in the bottom part of a component.

It has been confirmed that the proposed generalized estimation scheme makes it possible to predicting the occurrence of a defect in the form of shrinkage depression at all stages and under different technological conditions for a deformation process. Obtaining a preliminary assessment, based on it, of possible defect formation would facilitate the development of appropriate technological recommendations to avoid defects of this type

Author Biographies

Natalia Hrudkina, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

PhD

Department of Metal Forming

Leila Aliieva, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

Doctor of Technical Sciences, Associate Professor

Department of Metal Forming

Payman Abhari, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

Doctor of Technical Sciences, Associate Professor

Department of Metal Forming

Oleg Markov, Donbass State Engineering Academy Akademichna str., 72, Kramatorsk, Ukraine, 84313

Doctor of Technical Sciences, Professor, Head of Department

Department of Computerized Design and Modeling of Processes and Machines

Liudmyla Sukhovirska, Donetsk National Medical University Pryvokzalna str., 27, Lyman, Ukraine, 84404

PhD

Department of Medical Physics and Information Technologies No. 2

References

  1. Markov, O., Zlygoriev, V., Gerasimenko, O., Hrudkina, N., Shevtsov, S. (2018). Improving the quality of forgings based on upsetting the workpieces with concave facets. Eastern-European Journal of Enterprise Technologies, 5 (1 (95)), 16–24. doi: https://doi.org/10.15587/1729-4061.2018.142674
  2. Zhang, S. H., Wang, Z. R., Wang, Z. T., Xu, Y., Chen, K. B. (2004). Some new features in the development of metal forming technology. Journal of Materials Processing Technology, 151 (1-3), 39–47. doi: https://doi.org/10.1016/j.jmatprotec.2004.04.098
  3. Plancak, M., Barisic, B., Grizelj, B. (2008). Different Possibilities of Process Analysis in Cold Extrusion. Key Engineering Materials, 367, 209–214. doi: https://doi.org/10.4028/www.scientific.net/kem.367.209
  4. Aliev, I. S. (1988). Radial extrusion processes. Soviet Forging and Sheet Metal Stamping Technology, 6, 1–4.
  5. Cho, H. Y., Min, G. S., Jo, C. Y., Kim, M. H. (2003). Process design of the cold forging of a billet by forward and backward extrusion. Journal of Materials Processing Technology, 135 (2-3), 375–381. doi: https://doi.org/10.1016/s0924-0136(02)00870-1
  6. Pepelnjak, T., Milutinović, M., Plančak, M., Vilotić, D., Randjelović, S., Movrin, D. (2016). The Influence of Extrusion Ratio on Contact Stresses and Die Elastic Deformations in the Case of Cold Backward Extrusion. Strojniški Vestnik - Journal of Mechanical Engineering, 62 (1), 41–50. doi: https://doi.org/10.5545/sv-jme.2015.3051
  7. Aliev, I. S., Lobanov, A. I., Borisov, R. S., Savchinskij, I. G. (2004). Investigation of die blocks with split matrixes for the processes of cross extrusion. Kuznechno-Shtampovochnoe Proizvodstvo (Obrabotka Metallov Davleniem), 8, 21–26.
  8. Farhoumand, A., Ebrahimi, R. (2009). Analysis of forward–backward-radial extrusion process. Materials & Design, 30 (6), 2152–2157. doi: https://doi.org/10.1016/j.matdes.2008.08.025
  9. Seo, J. M., Jang, D. H., Min, K. H., Koo, H. S., Kim, S. H., Hwang, B. B. (2007). Forming Load Characteristics of Forward and Backward Tube Extrusion Process in Combined Operation. Key Engineering Materials, 340-341, 649–654. doi: https://doi.org/10.4028/www.scientific.net/kem.340-341.649
  10. Kalyuzhnyi, V. L., Alieva, L. I., Kartamyshev, D. A., Savchinskii, I. G. (2017). Simulation of Cold Extrusion of Hollow Parts. Metallurgist, 61 (5-6), 359–365. doi: https://doi.org/10.1007/s11015-017-0501-1
  11. Noh, J., Hwang, B. B., Lee, H. Y. (2015). Influence of punch face angle and reduction on flow mode in backward and combined radial backward extrusion process. Metals and Materials International, 21 (6), 1091–1100. doi: https://doi.org/10.1007/s12540-015-5276-y
  12. Aliieva, L., Zhbankov, Y. (2015). Radial-direct extrusion with a movable mandrel. Metallurgical and Mining Industry, 11, 175–183.
  13. Filippov, Yu. K., Ignatenko, V. N., Golovina, Z. S., Anyuhin, A. S., Ragulin, A. V., Gnevashev, D. A. (2011). Teoreticheskoe issledovanie kombinirovannogo protsessa radial'nogo i obratnogo vydavlivaniya v konicheskoy matritse. Kuznechno-shtampovochnoe proizvodstvo. Obrabotka materialov davleniem, 7, 3–7.
  14. Laptev, A. M., Perig, A. V., Vyal, O. Y. (2013). Analysis of equal channel angular extrusion by upper bound method and rigid blocks model. Materials Research, 17 (2), 359–366. doi: https://doi.org/10.1590/s1516-14392013005000187
  15. Ogorodnikov, V. А., Dereven’ko, I. А., Sivak, R. I. (2018). On the Influence of Curvature of the Trajectories of Deformation of a Volume of the Material by Pressing on Its Plasticity Under the Conditions of Complex Loading. Materials Science, 54 (3), 326–332. doi: https://doi.org/10.1007/s11003-018-0188-x
  16. Dereven'ko, I. A. (2012). Deformiruemost' i kachestvo zagotovok v usloviyah kombinirovannogo formoizmeneniya. Obrabotka metallov davleniem, 3 (32), 87–96.
  17. Aliiev, I., Aliieva, L., Grudkina, N., Zhbankov, I. (2011). Prediction of the Variation of the Form in the Processes of Extrusion. Metallurgical and Mining Industry, 3 (7), 17–22.
  18. Shestakov, N. A. (1998). Energeticheskie metody rascheta protsessov obrabotki metallov davleniem. Moscow: MGIU, 125.
  19. Hrudkina, N., Aliieva, L., Abhari, P., Kuznetsov, M., Shevtsov, S. (2019). Derivation of engineering formulas in order to calculate energy-power parameters and a shape change in a semi-finished product in the process of combined extrusion. Eastern-European Journal of Enterprise Technologies, 2 (7 (98)), 49–57. doi: https://doi.org/10.15587/1729-4061.2019.160585
  20. Aliieva, L., Grudkina, N., Zhbankov, I. (2012). Analysis of billet deformation during the combined radialbackward extrusion. New technologies and achievements in metallurgy and materials engineering. Czestochowa: Quick-druk, 389–396.

Downloads

Published

2019-09-30

How to Cite

Hrudkina, N., Aliieva, L., Abhari, P., Markov, O., & Sukhovirska, L. (2019). Investigating the process of shrinkage depression formation at the combined radial-backward extrusion of parts with a flange. Eastern-European Journal of Enterprise Technologies, 5(1 (101), 49–57. https://doi.org/10.15587/1729-4061.2019.179232

Issue

Vol. 5 No. 1 (101) (2019): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2019 Natalia Hrudkina, Leila Aliieva, Payman Abhari, Oleg Markov, Liudmyla Sukhovirska

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.