Analysis of ways to improve the durability of tines

Authors

  • Геннадий Иванович Семчук Poltava State Agrarian Academy Skovorody str. 1/3, Poltava, Ukraine, 36003, Ukraine
  • Анатолий Андреевич Дудников Poltava State Agrarian Academy Skovorody str. 1/3, Poltava, Ukraine, 36003, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2013.18158

Keywords:

hardening method, vibration treatment, technological process, service life, durability

Abstract

The paper deals with analyzing the methods for improving the durability of parts and service life of tillage machines operating in extremely severe conditions (tillage).

The features of described in literature methods for hardening separate parts of agricultural machinery, used mainly in industrial production, are considered.

Methods for repairing working elements of tillage machines are listed. As a rule they are characterized by a high complexity of technological process, the need for expensive equipment, high cost of repaired parts and they have not yet found a wide use in agricultural repair production.

Some aspects of increasing the durability of working elements of tillage machines, particularly hoes, are shown.

The principle of more effective method for parts repair, using vibrations of processing tool for developing and applying technological process of hardening the working elements of tillage machines, is considered.

The necessity of theoretical and practical research for determining the operating parameters of vibration hardening of hoes surface is shown.

Author Biographies

Геннадий Иванович Семчук, Poltava State Agrarian Academy Skovorody str. 1/3, Poltava, Ukraine, 36003

Undergraduate

Chair repair of machines and technology of construction materials

Faculty of Engineering and Technology

Анатолий Андреевич Дудников, Poltava State Agrarian Academy Skovorody str. 1/3, Poltava, Ukraine, 36003

PhD, Professor, Head of repairing machinery and technology of construction materials

Faculty of Engineering and Technology

References

  1. Ахметшин, Т. Ф. Повышение износостойкости и долговечности стрельчатых лап культиваторов [Текст] : дисс. канд. техн. наук. / Т. Ф. Ахметшин. – М.: 1988. – 245 с.
  2. Семчук, Г. И. Конструктивно-технологические характеристики культиваторных лап [Текст] / Г. И Семчук, А. А. Дудников, А. В. Мелешко, В. В. Гуленко // Восточно-Европейский журнал передовых технологий. – 2013. – №3/12. – С. 33-37.
  3. Войтюк, Д. Г. Сільськогосподарські та меліоративні машини [Текст] / Д. Г. Войтюк, В. М. Барановський, В. М. Булгаков та ін. – К.: Вища освіта, 2005. – 464 с.
  4. Юшков, В. В. Поточно-механизированная линия восстановления лап культиваторов [Текст] / В. В. Юшков, А. Г. Квакин, А. А. Князев, В. П. Терентьев // Техника в сельском хозяйстве. – 1986. – №8. – С. 51-52.
  5. Михальченков, А. М. Восстановление деталей двухслойной наплавкой [Текст] / А. М. Михальченков // Механизация и электрификация сельского хозяйства. – 1995. – №1. – С. 22-23.
  6. Методика определения экономической эффективности технологий и сельскохозяйственной техники [Текст] / Нормативно-справочный материал. – Ч. 1, 2. – М.: 1998. – 470 с.
  7. Аулін, В. В. Характер та інтенсивність зношування робочих органів ґрунтообробних машин [Текст] / В. В. Аулін, В. М. Бобрицький // Проблеми трибології. – Хмельницький: ХДУ, 2004. – №2. – С. 107-112.
  8. Афанасьев, А. А. Повышение качества поверхностей деталей машин [Текст] / А. А. Афанасьев. – Белгород: БГТУ, 2007. – 234 с.
  9. Бетеня, Г. Ф. Наненсение износостойких покрытий при упрочнении и восстановлении почвореж ущих элементов наплавкой намораживанием [Текст] / Г. Ф. Бетеня, Н. В. Кардаш, Н. А. Затко и др. // Защитные покрытия на металлах. – 1990. – Вып. 24. – С. 94-97.
  10. Дудников, И. А. Влияние вибрационной обработки на упрочнение обрабатываемой поверхности [Текст] / И. А. Дудников, А. И. Беловод, А. А Дудников и др. // Вибрации в технике и технологиях. – 2010. – №1(57). – С. 92-93.
  11. Akhmetshin, T. F. (1988). Increase the wear resistance and durability wing shares cultivators. Moscow: Science, 245.
  12. Semchuk, G. I., Dudnikov, A. A., Myaleshka, V. V., Gulenko, A. V. (2013). Design and technological features tines. East European Journal of advanced technologies, Kharkov, №3/12, 33-37.
  13. Voytyuk, D. G., Baranovsky, V. M., Bulgakov, V. M. (2005). Sіlskogospodarskі that melіorativnі machine. Kiev: Vishcha Osvita, 464.
  14. Yushkov, V. V., Kvakin, A. G., Knyazev, A. A., Terentev, V. P. (1986). Automatic production line recovery tine. Technika in agriculture, № 8, 51-52.
  15. Mihalchenkov, A. M. (1995). Restore the detail a two-layer cladding. Mechanization and electrification of agriculture, № 1, 22-23.
  16. Methods of determining the cost-effectiveness of technologies and agricultural equipment. (1998). Regulatory reference. Part 1, 2. Moscow: 470.
  17. Aulіn, V. V., Bobritsky, V. M. (2004). The nature of that іntensivnіst znoshuvannya Working organіv gruntoobrobnih machines. Problems tribologіi. Khmelnytsky: KSU, № 2, 107-112.
  18. Afanasyev, A. A. (2007). Improving the quality of the surfaces of machine parts. Belgorod State Technological University, 234.
  19. Beten, G. F., Kardash, N. V., Zatko, N. A. (1990). Nanensenie wear-resistant coatings for hardening and recovery pochvorezhuschih elements surfacing freezing. Protective coatings on metals, №24, 94-97.
  20. Dudnikov, I. A., Belovod, A. I., Dudnikov, A. A. (2010). The influence of vibration treatment on the treated surface hardening. Vibrations in engineering and technology, № 1 (57), 92-93.

Downloads

Published

2013-10-28

How to Cite

Семчук, Г. И., & Дудников, А. А. (2013). Analysis of ways to improve the durability of tines. Eastern-European Journal of Enterprise Technologies, 5(1(65), 67–71. https://doi.org/10.15587/1729-4061.2013.18158

Issue

Vol. 5 No. 1(65) (2013): Mechanical engineering technology

Section

Mechanical engineering technology

License

Copyright (c) 2014 Геннадий Иванович Семчук, Анатолий Андреевич Дудников

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.