Increase of reliability of v-belt transmissions ofmechanical presses
DOI:
https://doi.org/10.15587/1729-4061.2013.18536Keywords:
press, transmission, belts, reliability, failure, stress, pull factor, number of cycles, reservation, completenessAbstract
The problem of increasing the durability of V-belt transmissions of mechanical presses is considered in the paper. The issue of determining the factors that influence durability and ways of its improvement is set. Based on fatigue strength provisions it was found that transmission durability is determined primarily by the largest stress value in transmission sides and the number of belt runs. The major way of increasing the durability is ensuring the minimum initial tension, sufficient for design load transmission, and its systematic control. Durability of belts is improved by increasing transmission ratio, reducing the number of runs, increasing spacing on centers. Durability of drive as a whole is determined by reliability of separate belts, their quantity and condition of drive failure as a system. Increasing the number of transmission belts improves durability of transmission as a whole only with the use of hot standby. The research results can be used in designing belt transmissions of other technological and transport machines for increasing their performance standards.
References
- Кулаков Н.Д. О путях повышения долговечности клиновых ремней в приводе кривошипного горячештамповочного пресса / Н.Д. Кулаков // Кузнечно-штамповочное производство. – 1965, – № 1. – С. 38–41.
- Пожидаев Н.Н. К расчету клиноременных передач кривошипных прессов на долговечность / Н.Н. Пожидаев, Э.Ф. Богданов // Труды МВТУ, № 263. – М.: Машиностроение, 1978. С. 88–100.
- Буланов Э.А. Расчет ременных передач на заданный ресурс / Э.А. Буланов, А.А. Зубарев // Вестник машиностроения. – 1995, – № 1. – С. 18–20.
- Буланов Э.А. Расчет ременных передач // Вестник машиностроения. – 2001, – № 12. – С. 14–21.
- Вирабов Р.В. Тяговые свойства клиноременной передачи / Р.В. Вирабов, С.И. Чепурной // Вестник машиностроения. – 1981, – № 4. С. 20–27.
- Вирабов Р.В. Тяговые свойства фрикционных передач / Р.В. Вирабов. – М.: Машиностроение, 1982. – 263 с.
- Пронин Б.А. Бесступенчатые клиноременные и фрикционные передачи (вариаторы) / Б.А. Пронин, Г.А. Ревков. – М.: Машиностроение, 1980. – 320 с.
- Самошкин С.Л. Влияние отклонений геометрических размеров канавок шкивов на нагруженность ремней клиноременных передач / С.Л. Самошкин // Вестник машиностроения. – 1987, – № 2. С. 30–32.
- Самошкин С.Л. Определение неравномерности распределения окружного усилия при отклонении ширины ремней многоручьевой передачи / С.Л. Самошкин // Вестник машиностроения. – 1977, – № 8. С. 24–26.
- Самошкин С.Л. Распределение начального натяжения по ремням многоручьевой клиноременной передачи / С.Л. Самошкин, С.Е. Петраков // Вестник машиностроения. – 1975, – № 8. С. 34–36.
- Явлинская Р.Г. О распределении нагрузки между параллельно работающими ремнями в клиноременном приводе / Р.Г. Явлинская // Передаточные механизмы / Под ред. Б.А. Пронина и В.Ф. Мальцева. — М.: Машиностроение, 1971. С. 327–331.
- Гнеденко Б.В. Математические методы в теории надежности / Б.В. Гнеденко, Ю.К. Беляев, А.Д. Соловьев. – М.: Наука, 1965. – 524 с.
- Kulakov N.D. (1965). About the ways of increase of longevity of wedge belts in the crank-type maxipresses drive [O putjach povishenia dolgovechnosti klinovich remnej v privode krivoshipnogo gorjacheshtampovochnogo pressa]. Kuznechno-shtampovochnoe proizvodstvo – Forge–
- stamping production, no. 1, pp. 38–41.
- Pozhidaev N.N., Bogdanov E.F. (1978). To the calculation of V-belt transmissions of crank-type presses on longevity [K rachtetu klinoremenich peredach na dolgovechnost]. Trudi MVTU – Collection of science papers of MVTU, № 263. – M.: Engineer, pp. 88–100.
- Bulanov E.A., Zubarev A.A. (1995). Calculation of belt transmissions for the set resource [Rastchet remenih peredatch na zadanij resurs]. Vestnik mashinostroenia – Engineer bulletin, no.1, pp. 18–20.
- Bulanov E.A. (2001). A Calculation of belt transmissions [Raschet remenih peredatch]. Vestnik mashinostroenia – Engineer bulletin, no.12, pp. 14–21.
- Virabov R.V., Chepurnoy S.I. (1981). Hauling properties of V-belt transmission [Tjagovie svojstva klinoremenoj peredatchi]. Vestnik mashinostroenia – Engineer bulletin, no.4, pp. 20–27.
- Virabov R.V. (1982). Hauling properties of friction-gears [Tjagovie svojstva friczionih peredatch]. – M.: Engineer, 263 p.
- Pronin B.A., Revkov G.A. (1980). Stepless V-belt and friction transmissions [Besstupenchatie klonoremenie i frikzionie peredatchi]. – M.: Engineer, 1980, 320 p.
- Samoshkin S.L. (1987). Influence of rejections of geometrical sizes of ditches of pulleys on load straps of V-belt transmissions [Vlijanie otkloneniy geometricheskih razmerov kanavok shkivov na nagrujenost remnej klonoremenih peredatch]. Vestnik mashinostroenia – Engineer bulletin, no.2, pp. 30–32.
- Samoshkin S.L. (1977). Determination of unevenness of distributing of circuitous effort at the rejection of width of straps of stream pulley transmission [Opredelenie neravnomernosti raspredelenia okrujnogo usilia pri otklinenii shirini remnej mnogorutchevoj peredatchi]. Vestnik mashinostroenia – Engineer bul-letin, no.8, pp. 24–26.
- Samoshkin S.L., Petrakov S.E. (1975). Distributing of initial pull on the straps of stream pulley of V-belt transmission [Raspredelenie natchalnogo natjajshenia po remnjam mnogorutchevoj peredatchi]. Vestnik mashinostroenia – Engineer bulletin, no.8, pp. 34–36.
- Yavlinskaya R.G. (1971). About the partition of load between parallell workings straps in a V-belt drive [O raspredelenii nagruski mejdu paralelno rabotajushimi remnjami v kliniremenom privode]. Privodi mashin – Transmission mechanisms / Under B.A. Pronina and V.F. Mal'ceva. — M.: Engi-neer, pp. 327–331.
- Gnedenko B.V., Belyaev Yu.K., Solovyov A.D. (1965). Mathematicheskie metodi v teorii nadejnosti [Mathematical methods in the theory of reliability]. – M.: Science, 524 p.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2014 Александр Викторович Явтушенко, Анна Владимировна Явтушенко
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.