Exchange interaction and models of contact generation of disturbances in tribosystems

Authors

DOI:

https://doi.org/10.15587/1729-4061.2020.209927

Keywords:

contact tribodynamics, corpuscular-vortex-wave thermal complex, exchange interaction, collapse, acoustic emission

Abstract

The physical mechanisms have been investigated that form and transform the corpuscular-vortex-wave thermal complexes of disturbances in contact tribosystems based on the quantum-mechanical exchange interaction. The presence of a contact gap determines the generation of pairs of quasi-particles-disturbances stabilized by wavelength and frequency. Internal instability and collapse processes in such a system of disturbances lead to the formation of defects in a tribopair's material and underlie the emergency friction regimes. This paper gives specific technical examples of the generation of thermal complexes at fretting, during the friction of sliding and rolling, and at cutting. It has been established that the destructive nature of the process of fretting at low values of reverse sliding speeds is caused by the generation and collapse of the corpuscular-vortex-wave thermal complexes. An example of acoustic friction emission in the ultrasonic region of the spectrum has been used to show the quantum nature of the disturbances generated by friction. The high-frequency spectrum of acoustic emission corresponds to the unbalanced composition of the disturbances and leads to the formation of wear particles. The exchange interaction in a tribosystem involving rolling on the plane has been considered. The results of statistical analysis of such rolling showed the existence of the effect of negative friction caused by the quantum generation of longwave disturbances. It has been demonstrated that the collapsed component of the generation of disturbances is significantly increased under the modes of materials destruction, including when cutting the materials. The corpuscular-vortex-wave mechanism of selective transfer and hydrogen wear in tribosystems has been described. It is shown that the properties of a servovite film under the mode of selective transfer are provided by the collapse processes in the system of disturbances. Similar processes at the vortex-wave transfer of hydrogen atoms in metals lead to the wear and destruction of the surface layer of friction

Author Biographies

Yuriy Zaspa, Khmelnytskyi National University Instytuts’ka str., 11, Khmelnytskyi, Ukraine, 29016

PhD, Associate Professor

Department of Physics an Engineering

Aleksandr Dykha, Khmelnytskyi National University Instytuts’ka str., 11, Khmelnytskyi, Ukraine, 29016

Doctor of Technical Sciences, Professor, Head of Department

Department of Machines’ Durability and Reliability

Dmytro Marchenko, Mykolaiv National Agrarian University Georgiy Gongadze str., 9, Mykolayiv, Ukraine, 54020

PhD, Associate Professor

Department of Tractors and Agricultural Machinery, Operation and Technical Service

Serhii Matiukh, Khmelnytskyi National University Instytuts’ka str., 11, Khmelnytskyi, Ukraine, 29016

PhD, Associate Professor, Vice-rector of Scientific and Pedagogical Work

Yuri Kukurudzyak, Vinnytsia National Technical University Khmelnytske shoes str., 95, Vinnytsya, Ukraine, 21021

PhD, Associate Professor

Department of Automobiles and Transport Management

References

  1. Silveirinha, M. G. (2014). Theory of quantum friction. New Journal of Physics, 16 (6), 063011. doi: https://doi.org/10.1088/1367-2630/16/6/063011
  2. Esirkepov, T. Z., Bulanov, S. V. (2017). Paradoxical stabilization of forced oscillations by strong nonlinear friction. Physics Letters A, 381 (32), 2559–2564. doi: https://doi.org/10.1016/j.physleta.2017.06.007
  3. Suzuki, K., Hirai, Y., Ohzono, T. (2014). Oscillating Friction on Shape-Tunable Wrinkles. ACS Applied Materials & Interfaces, 6 (13), 10121–10131. doi: https://doi.org/10.1021/am5010738
  4. Dykha, A. V., Zaspa, Y. P., Slashchuk, V. O. (2018). Triboacoustic Control of Fretting. Journal of Friction and Wear, 39 (2), 169–172. doi: https://doi.org/10.3103/s1068366618020046
  5. Dykha, A., Matyukh, S. (2018). Triboacoustic diagnostic fixed joints of machines. MATEC Web of Conferences, 182, 02017. doi: https://doi.org/10.1051/matecconf/201818202017
  6. Aulin, V., Hrynkiv, A., Lysenko, S., Rohovskii, I., Chernovol, M., Lyashuk, O., Zamota, T. (2019). Studying truck transmission oils using the method of thermal-oxidative stability during vehicle operation. Eastern-European Journal of Enterprise Technologies, 1 (6 (97)), 6–12. doi: https://doi.org/10.15587/1729-4061.2019.156150
  7. Aulin, V., Hrynkiv, A., Lysenko, S., Zamota, T., Pankov, A., Tykhyi, A. (2019). Determining the rational composition of tribologically active additive to oil to improve characteristics of tribosystems. Eastern-European Journal of Enterprise Technologies, 6 (12 (102)), 52–64. doi: https://doi.org/10.15587/1729-4061.2019.184496
  8. Aulin, V., Hrynkiv, A., Lysenko, S., Lyashuk, O., Zamota, T., Holub, D. (2019). Studying the tribological properties of mated materials C61900 - A48-25BC1.25BNo. 25 in composite oils containing geomodifiers. Eastern-European Journal of Enterprise Technologies, 5 (12 (101)), 38–47. doi: https://doi.org/10.15587/1729-4061.2019.179900
  9. Aulin, V., Hrynkiv, A., Lysenko, S., Dykha, A., Zamota, T., Dzyura, V. (2019). Exploring a possibility to control the stressed­strained state of cylinder liners in diesel engines by the tribotechnology of alignment. Eastern-European Journal of Enterprise Technologies, 3 (12 (99)), 6–16. doi: https://doi.org/10.15587/1729-4061.2019.171619
  10. Li, Q., Popov, V. L. (2018). On the Possibility of Frictional Damping with Reduced Wear: A Note on the Applicability of Archard's Law of Adhesive Wear under Conditions of Fretting. Physical Mesomechanics, 21 (1), 94–98. doi: https://doi.org/10.1134/s1029959918010137
  11. Wetter, R., Popov, V. L. (2016). The Influence of System Dynamics on the Frictional Resistance: Insights from a Discrete Model. Tribology Letters, 61(2). doi: https://doi.org/10.1007/s11249-015-0635-x
  12. Aleksandr, D., Dmitry, M. (2018). Prediction the wear of sliding bearings. International Journal of Engineering & Technology, 7 (2.23), 4–8. doi: https://doi.org/10.14419/ijet.v7i2.23.11872
  13. Dykha, A., Sorokatyi, R., Makovkin, O., Babak, O. (2017). Calculation-experimental modeling of wear of cylindrical sliding bearings. Eastern-European Journal of Enterprise Technologies, 5 (1 (89)), 51–59. doi: https://doi.org/10.15587/1729-4061.2017.109638
  14. Marchuk, V. Y., Kindrachuk, M. V., Mirnenko, V. I., Mnatsakanov, R. G., Kornіenko, A. O., Bashta, O. V., Fedorchuk, S. V. (2019). Physical Interpretations of Internal Magnetic Field Influence on Processes in Tribocontact of Textured Dimple Surfaces. Journal of Nano- and Electronic Physics, 11 (5), 05013-1–05013-5. doi: https://doi.org/10.21272/jnep.11(5).05013
  15. Marchuk, V., Kindrachuk, M., Kryzhanovskyi, A. (2014). System analysis of the properties of discrete and oriented structure surfaces. Aviation, 18 (4), 161–165. doi: https://doi.org/10.3846/16487788.2014.985474
  16. Kindrachuk, M. V., Vol’chenko, А. I., Vol’chenko, D. А., Skrypnyk, V. S., Voznyi, А. V. (2019). Energy Levels of Different Types of Contacts of Microirregularities of Friction Couples. Materials Science, 54 (6), 843–854. doi: https://doi.org/10.1007/s11003-019-00272-5
  17. Sorokatyi, R., Chernets, M., Dykha, A., Mikosyanchyk, O. (2019). Phenomenological Model of Accumulation of Fatigue Tribological Damage in the Surface Layer of Materials. Mechanisms and Machine Science, 3761–3769. doi: https://doi.org/10.1007/978-3-030-20131-9_371
  18. Dykha, A., Sorokatyi, R., Dytyniuk, V. (2019). Model of accumulation of tribo damage in high-speed friction. BALTTRIB' 2019: proceedings of X international scientific conference, Vytautas Magnus University, Agriculture Academy. Kaunas, 180–186. Available at: https://www.vdu.lt/cris/bitstream/20.500.12259/103203/1/ISSN2424-5089_2019.PG_180-186.pdf
  19. Dykha, A., Makovkin, O. (2019). Physical basis of contact mechanics of surfaces. Journal of Physics: Conference Series, 1172, 012003. doi: https://doi.org/10.1088/1742-6596/1172/1/012003
  20. Dykha, A., Aulin, V., Makovkin, O., Posonskiy, S. (2017). Determining the characteristics of viscous friction in the sliding supports using the method of pendulum. Eastern-European Journal of Enterprise Technologies, 3 (7 (87)), 4–10. doi: https://doi.org/10.15587/1729-4061.2017.99823
  21. Danilov, S. D., Gurarie, D. (2000). Quasi-two-dimensional turbulence. Physics-Uspekhi, 43 (9), 863–900. doi: https://doi.org/10.1070/pu2000v043n09abeh000782
  22. Zaspa, Y. P. (2012). Coherent tribodynamics. Journal of Friction and Wear, 33 (6), 490–503. doi: https://doi.org/10.3103/s1068366612060128
  23. Myshkin, N. K., Markova, L. V. (2017). Trends in On-line Tribodiagnostics. On-Line Condition Monitoring in Industrial Lubrication and Tribology, 203–223. doi: https://doi.org/10.1007/978-3-319-61134-1_6
  24. Briscoe, B. J., Chateauminois, A., Chiu, J., Vickery, S. (2001). Acoustic noise emission in a model PMMA/steel fretting contact. Tribology Research: From Model Experiment to Industrial Problem - A Century of Efforts in Mechanics, Materials Science and Physico-Chemistry, Proceedings of the 27th Leeds-Lyon Symposium on Tribology, 673–681. doi: https://doi.org/10.1016/s0167-8922(01)80149-8
  25. Akay, A. (2002). Acoustics of friction. The Journal of the Acoustical Society of America, 111 (4), 1525–1548. doi: https://doi.org/10.1121/1.1456514
  26. Kolubaev, A. V., Kolubaev, E. A., Vagin, I. N., Sizova, O. V. (2005). Sound Generation in Sliding Friction. Technical Physics Letters, 31 (10), 813–816. doi: https://doi.org/10.1134/1.2121824
  27. Rubtsov, V. E., Kolubaev, E. A., Kolubaev, A. V., Popov, V. L. (2013). Using acoustic emission for the analysis of wear processes during sliding friction. Technical Physics Letters, 39 (2), 223–225. doi: https://doi.org/10.1134/s1063785013020235
  28. Markova, L. V., Myshkin, N. K., Kong, H., Han, H. G. (2011). On-line acoustic viscometry in oil condition monitoring. Tribology International, 44 (9), 963–970. doi: https://doi.org/10.1016/j.triboint.2011.03.018
  29. Zinin, M. A., Gavrilov, S. A., Shchedrin, A. V., Garkunov, D. N. (2011). Influence of metal-cladding addivite valena on combined machining. Russian Engineering Research, 31 (9), 880–884. doi: https://doi.org/10.3103/s1068798x11090292
  30. Shchedrin, A. V., Bekaev, A. A., Garkunov, D. N., Mel’nikov, E. A., Gavrilyuk, V. S. (2011). Improvement in hybrid drawing by a tool with regular microgeometry on the basis of metal-coating additives. Russian Engineering Research, 31 (4), 365–368. doi: https://doi.org/10.3103/s1068798x1104023x

Downloads

Published

2020-08-31

How to Cite

Zaspa, Y., Dykha, A., Marchenko, D., Matiukh, S., & Kukurudzyak, Y. (2020). Exchange interaction and models of contact generation of disturbances in tribosystems. Eastern-European Journal of Enterprise Technologies, 4(5 (106), 25–34. https://doi.org/10.15587/1729-4061.2020.209927

Issue

Vol. 4 No. 5 (106) (2020): Applied physics

Section

Applied physics

License

Copyright (c) 2020 Yuriy Zaspa, Aleksandr Dykha, Dmytro Marchenko, Serhii Matiukh, Yuri Kukurudzyak

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.