Determining the elastic-plastic effective width of the free flange of a hull girder with the breaking of a wall

Authors

DOI:

https://doi.org/10.15587/1729-4061.2021.225106

Keywords:

girder with an axis/edge/wall breaking, I-girder, concentration factor

Abstract

This paper reports the dependences that have been derived to determine the effective width of a free flange in a dangerous cross-section of the wide-flange hull girder with the breaking of the wall/edges/axis at elastic-plastic deformation depending on the applied load for a perfectly plastic material without strengthening. Currently, there are no systematic dependences to determine the effective width of the free flange of girders of this type, except for certain cases. The technique is suitable for use for both purely elastic and elastic-plastic deformation. To calculate the stressed-strained state (SSS), a finite-element method (FEM) was used to solve the three-dimensional problem from the elasticity and plasticity theory. It has been shown that the node is exposed to simple loading. The reported results were derived within the framework of the deformation theory of plasticity. The largest ratio of external load to the boundary of fluidity is 0.9. The estimation scheme takes into consideration the most unfavorable working conditions of the examined node when the safest data are acquired. The dependences were built for the theoretical coefficient of concentration in a dangerous cross-section, which is used in the proposed procedure to determine the moment of transition from the elastic stage of deformation to elastic-plastic. When determining the effective width, the complex work of the flange and its deplanation was taken into consideration by defining the SSS components in the median plane. The feasibility of the idea of designing the SSS components on the inclined plane of a free flange has been proven. In this case, there is practically a (quasi) flat stressed state, suitable for the application of classical methods to determine the effective width. The proposed technique simplifies the calculations of the strength of the examined girder.

Author Biographies

Valerii Sokov, Admiral Makarov National University of Shipbuilding

Assistant

Department of Structural Mechanics and Ship Construction

Leontii Korostylov, Admiral Makarov National University of Shipbuilding

Doctor of Technical Sciences, Professor

Department of Structural Mechanics and Ship Construction

References

  1. Sokov, V. M. (2020). Veryfikatsiia ta modyfikatsiya formuly V. P. Suslova dlia efektyvnoi shyryny vilnoho poiasku balky zi zlamom stinky. Suchasni tekhnolohiyi proektuvannia, pobudovy, ekspluatatsiyi i remontu suden, morskykh tekhnichnykh zasobiv i inzhenernykh sporud: materialy vseukrainskoi naukovo-tekhnichnoi konferentsiyi z mizhnarodnoiu uchastiu. Mykolaiv: NUK, 106–110.
  2. Sokov, V. M. (2020). Efektyvna shyryna vilnoho flantsia sudnovoi balky zi zlamom stinky v nebezpechnomu pererizi. Inovatsiyi v sudnobuduvanni ta okeanotekhnitsi: materialy XI mizhnarodnoi naukovo-tekhnichnoi konferentsiyi. Mykolaiv: NUK, 233–236.
  3. Belenkiy, L. M., Raskin, Y. N., Vuillemin, J. (2007). Effective plating in elastic–plastic range of primary support members in double-skin ship structures. Marine Structures, 20 (3), 115–123. doi: https://doi.org/10.1016/j.marstruc.2007.06.002
  4. Hansen, T., Gath, J., Nielsen, M. P. (2010). An improved effective width method based on the theory of plasticity. Advanced Steel Construction, 6 (1), 515–547. doi: https://doi.org/10.18057/ijasc.2010.6.1.1
  5. Lin, Z., Zhao, J. (2012). Modeling inelastic shear lag in steel box beams. Engineering Structures, 41, 90–97. doi: https://doi.org/10.1016/j.engstruct.2012.03.018
  6. Yemelin, Y. (1992). On the effective width of girder flanges in elastic and elasto-plastic stages. Journal of Constructional Steel Research, 21 (1-3), 195–204. doi: https://doi.org/10.1016/0143-974x(92)90027-c
  7. Shi, Q.-X., Wang, B. (2015). Simplified calculation of effective flange width for shear walls with flange. The Structural Design of Tall and Special Buildings, 25 (12), 558–577. doi: https://doi.org/10.1002/tal.1272
  8. Cheng, X., Chen, Y., Pan, L. (2013). Experimental study on steel beam–columns composed of slender H-sections under cyclic bending. Journal of Constructional Steel Research, 88, 279–288. doi: https://doi.org/10.1016/j.jcsr.2013.05.020
  9. Erkmen, B., Kilic, B. T. (2019). Determination of Effective Breadth Width of Steel Plate‐Stiffener Based on Nonlinear FE Analysis. The 14th Nordic Steel Construction Conference, 3 (3-4), 829–834. doi: https://doi.org/10.1002/cepa.1141
  10. Okabe, T., Takeda, N. (2002). Elastoplastic shear-lag analysis of single-fiber composites and strength prediction of unidirectional multi-fiber composites. Composites Part A: Applied Science and Manufacturing, 33 (10), 1327–1335. doi: https://doi.org/10.1016/s1359-835x(02)00170-7
  11. Kimura, S., Koyanagi, J., Hama, T., Kawada, H. (2007). An Improved Shear-Lag Model for a Single Fiber Composite with a Ductile Matrix. Key Engineering Materials, 334-335, 333–336. doi: https://doi.org/10.4028/www.scientific.net/kem.334-335.333
  12. Nie, J.-G., Tian, C.-Y., Cai, C. S. (2008). Effective width of steel–concrete composite beam at ultimate strength state. Engineering Structures, 30 (5), 1396–1407. doi: https://doi.org/10.1016/j.engstruct.2007.07.027
  13. Timoshenko, S. P., Goodier, J. N. (1970). Theory of Elasticity Audio CD. New York: McGraw-Hill Book Company.
  14. Suslov, V. P., Kochanov, Yu. P., Spihtarenko, V. N. (1972). Stroitel'naya mehanika korablya i osnovy teorii uprugosti. Leningrad: Sudostroenie, 720.
  15. Eremenko, S. Yu. (1991). Metody konechnyh elementov v mehanike deformiruemyh tel. Kharkiv: Izd-vo «Osnova» pri Khark. un-te., 272.
  16. Mozharovskiy, N. S., Kachalovskaya, N. E. (1991). Prilozhenie metodov teorii plastichnosti i polzuchesti k resheniyu inzhenernyh zadach mashinostroeniya. Ch. 2: Metody i algoritmy resheniya kraevyh zadach. Kyiv: «Vishcha shkola», 287.

Downloads

Published

2021-02-22

How to Cite

Sokov, V., & Korostylov, L. . (2021). Determining the elastic-plastic effective width of the free flange of a hull girder with the breaking of a wall . Eastern-European Journal of Enterprise Technologies, 1(7 (109), 32–40. https://doi.org/10.15587/1729-4061.2021.225106

Issue

Vol. 1 No. 7 (109) (2021): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2021 Valerii Sokov, Леонтий Иванович Коростылев

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.