Calculation of motion parameters of discrete pneumatic unit on the basis of the elastic-viscosity model

Authors

  • Геннадий Анатолиевич Крутиков Национальный технический университет «Харьковский политехнический институт» ул. Фрунзе, 21, г. Харьков, 61002, Ukraine
  • Марьяна Георгиевна Стрижак Национальный технический университет «Харьковский политехнический институт» ул. Фрунзе, 21, г. Харьков, 61002, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2011.2314

Keywords:

Discrete pneumatic units, mathematical modeling of workflow, elastic-viscosity model

Abstract

The one way of mathematical modeling of the workflow in digital pneumatic units, based on considering the equilibrium conditions for single-mass elastic-viscous model (Maxwell model) is shown. The solutions obtained in this way are compact and have the necessary accuracy for practical calculation

Author Biographies

Геннадий Анатолиевич Крутиков, Национальный технический университет «Харьковский политехнический институт» ул. Фрунзе, 21, г. Харьков, 61002

Кандидат технических наук, доцент

Кафедра «Гидропневмоавто-матика и гидропривод»

Марьяна Георгиевна Стрижак, Национальный технический университет «Харьковский политехнический институт» ул. Фрунзе, 21, г. Харьков, 61002

Аспирант

Кафедра «Гидропневмоавтоматика и гидропривод»

References

  1. Крутиков Г.А. О стабилизации давления в быстродействующих пневмоприводах//Гидропривод и гидропневмоавтоматика. – Киев: Техніка, 1981, Вып. 17. – С. 108-113.
  2. Крутиков Г.А., Пекарь Л.А. О разработке линейной модели дискретного пневмопривода//В кн. Пневматика и гидравлика. Приводы и системы управления. – М., Машиностроение, 1990. – Вып. 15. – С. 120-128.
  3. Пановко Я.Г. Введение в теорию механических колебаний//Учебное пособие для ВТУЗов. – М., Наука, 1986, 270 с.

Downloads

How to Cite

Крутиков, Г. А., & Стрижак, М. Г. (2012). Calculation of motion parameters of discrete pneumatic unit on the basis of the elastic-viscosity model. Eastern-European Journal of Enterprise Technologies, 6(7(54), 47–50. https://doi.org/10.15587/1729-4061.2011.2314

Issue

Vol. 6 No. 7(54) (2011): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2014 Геннадий Анатолиевич Крутиков, Марьяна Георгиевна Стрижак

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.