Ensuring adhesion between the asphalt-concrete road surface and rigid base at the roadbed design stage
DOI:
https://doi.org/10.15587/1729-4061.2021.235394Keywords:
asphalt-concrete layer, elasticity module, stressed-strained state, adhesion, cement-concrete slabAbstract
Arranging asphalt-concrete layers on a rigid base in the form of cement-concrete slabs can significantly improve the transporting and operational performance of the road surface. Such a structural solution is appropriate in almost all countries of the world since cement-concrete slabs retain high strength for a long time. To prevent the rapid destruction of an asphalt-concrete road surface on a rigid base, it is necessary to ensure reliable adhesion between the layers' contacts and, at the design stage, to test the adhesion strength by estimation.
This paper has substantiated a criterion of adhesion strength in the contact between an asphalt-concrete road surface and the rigid base. The calculation involves comparing the active tangent stresses in the contact between layers dependent on the effect of the vertical and horizontal components of the transport load with the magnitude of permissible tangent shear stresses in the contact of layers.
The parameters for an estimation model have been established; the stressed-strained state of the roadbed structure has been simulated using a finite element method. When modeling the stressed-strained state and calculating based on the strength criterion, different vehicle traffic conditions have been considered, as well as the effect of temperature on the strength parameters of the asphalt-concrete layer and the tar layer. The conditions for vehicle movement, taken into consideration when designing, correspond to the conditions of movement along the road, along the curves in the plan and profiles, and notion conditions at car emergency braking. Practical recommendations have been compiled for assigning the minimum permissible thickness of an asphalt-concrete layer on a rigid base, which must be followed at the design stage due to the condition for ensuring reliable adhesion between the layers' contacts. The minimum permissible thickness ranges from 2 cm to 10 cm, depending on the conditions of movement, temperature, and the type of tar.
References
- Radovskiy, B. S. (2009). Tsementobetonnye pokrytiya v SShA. Dorozhnaya tekhnika, 1, 50–58.
- Pérez-Acebo, H., Gonzalo-Orden, H., Findley, D. J., Rojí, E. (2021). Modeling the international roughness index performance on semi-rigid pavements in single carriageway roads. Construction and Building Materials, 272, 121665. doi: https://doi.org/10.1016/j.conbuildmat.2020.121665
- Radovskiy, B. S. (2010). Opyt ispol'zovaniya starogo tsementobetona kak osnovaniya pod asfal'tobetonnoe pokrytie v SShA. Dorozhnaya tekhnika, 1, 20–32.
- Korochkin, A. V., Ahmetov, S. A. (2009). Zavisimost' sostoyaniya pokrytiya ot tolschiny asfal'tobetonnyh sloev zhestkoy dorozhnoy odezhdy. Avtomobil'nye dorogi, 12, 27–29.
- Onischenko, A., Aksenov, S., Nevynhlovskyy, V. (2016). Numerical Simulation of Stress-Strain State of Asphalt Concrete Pavement on the Carriageway of the South Bridge in Kiev. Procedia Engineering, 134, 322–329. doi: https://doi.org/10.1016/j.proeng.2016.01.014
- Dorozhko, E., Ryapuhin, V., Makovyey, R. (2016). Design Procedure by Strength Criteria of Asphalt Layers on a Rigid Base Taking into Account the Simultaneous Action of External Loads and Thermal Stresses. Procedia Engineering, 134, 101–108. doi: https://doi.org/10.1016/j.proeng.2016.01.045
- White, G. (2016). State of the art: interface shear resistance of asphalt surface layers. International Journal of Pavement Engineering, 18 (10), 887–901. doi: https://doi.org/10.1080/10298436.2015.1126270
- Korochkin, A. V. (2017). Teoriya rascheta zhestkoy dorozhnoy odezhdy s asfal'tobetonnym pokrytiem. Moscow: MADI, 148.
- Dorozhko, Y., Arsenieva, N., Sarkisian, H., Synovets, O. (2019). Determining the most dangerous loading application point for asphalt-concrete layers on a rigid base. Eastern-European Journal of Enterprise Technologies, 3 (7 (99)), 36–43. doi: https://doi.org/10.15587/1729-4061.2019.166490
- Lazăr, Ş. M., Răcănel, C. (2017). Flexible Pavement Design Criterion Based on Octahedral Shear Stresses. Romanian Journal of Transport Infrastructure, 6 (1), 54–65. doi: https://doi.org/10.1515/rjti-2017-0054
- Nevinhlovskyi, V. F. (2013). Teoretychni aspekty rozrakhunku zalyshkovoho resursu asfaltobetonnoho pokryttia na zalizobetonnykh avtodorozhnikh mostakh. Avtomobilni dorohy i dorozhnie budivnytstvo, 89, 225–234.
- Gladkiy, A. V., Ryapuhin, V. N. (2006). Osobennosti raschetov na prochnost' mnogosloynyh pokrytiy i usileniya nezhestkih dorozhnyh odezhd. Dorohy i mosty, 4, 232–247.
- Gladkiy, A. V. (2007). Napryazhenno-deformirovannoe sostoyanie mnogosloynyh pokrytiy dorozhnyh odezhd. Bicnyk Skhidnoukrainskoho natsionalnoho universytetu imeni Volodymyra Dalia, 6 (112), 105–108.
- Pisarenko, G. S. (1976). Deformirovanie i prochnost' materialov pri slozhnom napryazhennom sostoyanii. Kyiv, 415.
- Li, S., Liu, X., Liu, Z. (2014). Interlaminar shear fatigue and damage characteristics of asphalt layer for asphalt overlay on rigid pavement. Construction and Building Materials, 68, 341–347. doi: https://doi.org/10.1016/j.conbuildmat.2014.06.053
- Chen, X., Wu, S., Zhou, J. (2013). Analysis of mechanical properties of concrete cores using statistical approach. Magazine of Concrete Research, 65 (24), 1463–1471. doi: https://doi.org/10.1680/macr.13.00113
- Wang, X., Zhong, Y. (2019). Influence of tack coat on reflective cracking propagation in semi-rigid base asphalt pavement. Engineering Fracture Mechanics, 213, 172–181. doi: https://doi.org/10.1016/j.engfracmech.2019.04.015
- Golchin, B., Hamzah, M. O., Hasan, M. R. M. (2017). Optimization in producing warm mix asphalt with polymer modified binder and surfactant-wax additive. Construction and Building Materials, 141, 578–588. doi: https://doi.org/10.1016/j.conbuildmat.2017.02.123
- Assogba, O. C., Tan, Y., Sun, Z., Lushinga, N., Bin, Z. (2019). Effect of vehicle speed and overload on dynamic response of semi-rigid base asphalt pavement. Road Materials and Pavement Design, 22 (3), 572–602. doi: https://doi.org/10.1080/14680629.2019.1614970
- Dong, Z., Ni, F. (2014). Dynamic model and criteria indices of semi-rigid base asphalt pavement. International Journal of Pavement Engineering, 15 (9), 854–866. doi: https://doi.org/10.1080/10298436.2014.893322
- Merzlikin, A. E., Kapustnikov, N. V. (2010). Pogreshnosti, voznikayuschie pri raschete dorozhnyh odezhd s pomosch'yu metoda konechnyh elementov. Zhilischnoe stroitel'stvo, 10, 26–29.
- M 02070915-750:2016. Metodyka proektuvannia asfaltobetonnoho pokryttia zalizobetonnykh avtodorozhnikh mostiv.
- Riznichenko, O. S. (2012). Analiz icnuiuchykh metodiv proektuvannia asfaltobetonnoho pokryttia na mostakh za umovoiu zsuvostiykosti. Avtomobilni dorohy i dorozhnie budivnytstvo, 86, 30–36.
- Onishchenko, A. M., Riznichenko, O. S., Kurtyev, V. S. (2016). The method of determination bond between asphalt pavement and composite steel and concrete bridge. Visnyk NTU. Seriya: «Tekhnichni nauky», 1 (34), 319–327.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Yevhen Dorozhko, Angelika Batrakova, Vladislav Tymoshevskyi, Elina Zakharova
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.