Development and substantiation of parameters of the mechanism with flexible drive for the cutterbar of the mower of double knife stroke
DOI:
https://doi.org/10.15587/1729-4061.2021.239067Keywords:
mower, drive, cutting device, toe bar, segment-finger mower, alfalfa, grass mowing, double stroke, knife, speed, crankAbstract
This paper presents the results of experimental research on the development and substantiation of parameters and operating modes of the drive mechanism of the cutting apparatus in a mower with a double knife stroke.
A structural and technological scheme of the drive mechanism of the cutting device of the segment-finger type mower has been developed, in which a double stroke of the cutting device knife is provided. Analytical relationships were obtained to determine the knife stroke, speed and acceleration. Based on the results of theoretical and experimental studies, the main parameters of the mower drive mechanism were substantiated. Based on the condition of a high-quality cut of plants, at a minimum grass cutting speed, the minimum crank shaft speed was determined. By calculation, the feed area and the load area of the cutter for normal cutting with a double cut of the knife are determined. Analytical relationships were obtained to determine the power required to drive the cutterbar of a mower with a double knife stroke. Based on the research results, the main parameters of the mower with an improved drive are substantiated. An experimental sample was made and preliminary tests of the drive mechanism were carried out, agrotechnical and energy indicators of the mower operation were determined.
References
- Torekhanov, A. E. (2007). Development ways in fodder production. Bulletin of "Bastau" LLP, 29–37.
- Osobov, V. I., Vasiliev, G. K. (1983). Hay-harvesting machines and complexes. Moscow: Mechanical Engineering, 304.
- Logistics in fodder production (2003). New agriculture, 1, 16–20.
- Khalansky, V. M., Gorbachev, I. V. (2004). Agricultural machines. Moscow: Kolos, 249–260.
- Zinoviev, V. A. (1972). Course of the theory of mechanisms and machines. Moscow: Nauka, 384.
- Adilsheev, A. S. (2017). Scientific and technical basis for the development of mechanisms, etc. and water cutting machines sweepers. Almaty: the AD Time The, 159.
- Suranchiev, M. T. (2006). Substantiation of the parameters of the drive mechanism of the cutting device of a front mower with a movable finger bar. Almaty, 24.
- Rustamov, S. I. (1981). Physical and mechanical properties of plants and the improvement of cutting devices of harvesting machines. Kyiv-Donetsk: Visshaya shkola, 170.
- Reznikov, L. A., Eshchenko, V. T., Dyachenko, G. N. (1991). Basis of design and calculation of agricultural mashin. Moscow: Agropromizdat, 225–257.
- Dolgov, I. A. (Ed.) (1987). Complex mechanization of fodder production. Moscow: VO "Agropromizdat", 351.
- Adilsheev, A. S., Zhortuylov, O. (2015). Study of mechanism kinematic with flexible elastic links of double cutter bar grass reaper. Mechanization in agriculture & Conserving of the resources, 61 (1), 6–8. Available at: https://stumejournals.com/journals/am/2015/1/6.full.pdf
- Bobovich, I. S., Kostyuchenko, V. M. (1974). To the study of mechanisms with an elastic closed loop for driving mower knives. Scientific works of the Kazakh Agricultural Institute, XVII (4), 96–102.
- Bosoy, E. S. (1978). Theory, design and calculation of agricultural products machines. Moscow: Mashinostroenie, 268.
- Popov, I. F. (1978). Machines for harvesting grasses for hay. Moscow: Mashgiz, 268.
- Drozdov, N. I. (1961). Investigation of the process of cutting grasses and grain crops by cutting devices of harvesting machines. Moscow, 301.
- Zhortuylov, O., Seitbekov, L. S., Zhumatay, G. S., Adilsheev, A. S., Surzhin, V. I. (2008). Innovation Pat. No. 21946 Republic of Kazakhstan. The mechanism of the drive of the knife cutting device. No. 2008/1336; declareted: 02.12.2008; published: 15.12.2009, Bul. No. 12.
- Zhortuylov, O., Evtifeev, A. T., Alekseek, A. A., Adilsheev, A. S., Bekenov, U. E. (2011). Innovative Pat. No. 26421 Republic of Kazakhstan. The drive mechanism of the cutting device of the mower and reaper. No. 2011/1293.1; declareted: 12.12.2011; published: 02.14.2012, Bul. No. 2.
- Zhortuylov, O., Adilsheev, A. S., Evtifeev, A. T., Alekseek, A. A., Bekenov, U. E. (2013). Innovative Pat. No. 29916 Republic of Kazakhstan. Segment-finger mower. No. 2013/1928.1; declareted: 12.23.2013; published: 15.06.2015, Bul. No. 6.
- Klenin, N. I., Popov, I. F., Sakun, V. A. (1970). Agricultural machines: elements of the theory of working processes, calculation of control parameters and operating modes. Moscow: Kolos, 208–240.
- Zhumatay, G. S. (2010). Substantiation of parameters and development of the drive of the mower cutter with a double run of the knife. Almaty, 26.
- Zhortuylov, O., Adilsheev, A. S., Zhumatay, G. S. (2008). Substantiation of the parameters of the drive mechanism of the mower with a double run of the knife. Bulletin, Almaty, 8, 61–63.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Omirserik Zhortuylov, Gani Zhumatay, Askar Rzaliyev, Tokhtar Abilzhanuly, Orynzhamal Sarsembenova, Serik Bekbossynov, Daniyar Abilzhanov, Bauyrzhan Boranbayev
This work is licensed under a Creative Commons Attribution 4.0 International License.
The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.
A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.