Sensitivity of an acoustic emission to wearing of surfaces of a composite material

Authors

  • Сергей Федорович Филоненко National Aviation University Komarova 1, Kyiv, Ukraine, 03680, Ukraine
  • Татьяна Васильевна Нимченко National Aviation University Komarova 1, Kyiv, Ukraine, 03680, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2014.23971

Keywords:

acoustic emission, parameters, signal, composite, wear, friction, analysis, increase, surface

Abstract

The results of studying friction and wear of the surfaces of the composite material are considered. The analysis of the parameters of recorded resulting acoustic emission signal at the normal and extremely gross wear stages, as well as friction temperature and coefficient, is carried out. Temporal parameters of transition of the friction unit to the extremely gross wear stage are defined by the analyzed parameters. The analysis of change dependencies of percent increase in the analyzed parameters and their sensitivity to friction and wear of the frictional contactsurfaces of the composite material is performed. It is determined that, at the stage of normal wear, percent increase in the friction coefficient does not occur, and the percent increase in temperature grows linearly. It is found that the acoustic emission is more sensitive to friction and wear of the surfaces of the composite material relative to the temperature in the friction zone and friction coefficient. It is shown that acoustic emission allows to fix the stage that precedes the extremely gross wear stage, which is an important task in the diagnostics of friction units.

Author Biographies

Сергей Федорович Филоненко, National Aviation University Komarova 1, Kyiv, Ukraine, 03680

Professor, director

Institute of Information-Diagnostic Systems

Татьяна Васильевна Нимченко, National Aviation University Komarova 1, Kyiv, Ukraine, 03680

Candidate of Engineering, Associate Professor

Department of Information Security Tools, Institute of Information-Diagnostic Systems

References

  1. Piatkowska, A. Measurement and analysis of acoustic emission in the tribological system ball-on-disc [Text] / A. Piatkowska, T. Piatkowski // Diagnostyca. – 2007. – Vol. 4 (44). – P. 43–48.
  2. Hase, A. The relationship between acoustic emissions and wear particles for repeated dry rubbing [Text] / A. Hase, M. Wada, H. Mishina // Wear. – 2008. – Vol. 256 (5–6). – P. 831–839.
  3. Benabdallah, H. S. Acoustic Emission and Its Relationship with Friction and Wear for Sliding Contact [Text] / H. S. Benabdallah, D.A. Aguilar // Tribology Transactions. – 2008. – Vol. 51. – Р. 738–747.
  4. Raharjo, P. An investigation of surface vibration, airborne sound and acoustic emission characteristics of a journal bearing for early fault detection and diagnosis [Text] / P. Raharjo. – A thesis submitted of the requirements for the degree of Doctor of Philosophy (The University of Huddersfield), 2013. – 234 р.
  5. Fan, Y. Modelling acoustic emissions generated by sliding friction [Text] / Y. Fan, F. Gu, A. Ball // Wear. – 2010. – Vol. 268 (5–6). – Р. 811–815.
  6. Filonenko, S. F. Modelling of acoustic emission signals at friction of materials’ surface layers [Text] / S. F. Filonenko, V. M. Stadnychenko, A. P. Stahova // Aviation. – 2008. – Vol. 12 (3). – Р. 87–94.
  7. Filonenko, S. F. Definition of contact stress in friction units on the basis of the acoustic emission method [Text] / S. F. Filonenko, V. M. Stadnychenko, A. P. Stahova // Aviation. – 2009. – Vol. 13 (3). – Р. 72–77.
  8. Xu, J. Effect of Cr alloying on friction and wear of sputter-deposited nanocrystalline (MoxCr1−x)5Si3 films [Text] / J. Xu, Z.H. Xie, P. Munroe // Intermetallics. – 2011. – Vol. 19 (8). – Р. 1146–1156.
  9. Guo, J. ZhangInfluence of calcination temperature on structure as well as friction and wear behavior of CNx:H films on composite ceramic substrate [Text] / J. Guo, J. Zhang, L. Yu, Z. Wu // Thin Solid Films. – 2013. – Vol. 542 (2). – Р.60–70.
  10. Xu, J. Unraveling the mechanical and tribological properties of a novel Ti5Si3/TiC nanocomposite coating synthesized by a double glow discharge plasma technique [Text] / J. Xu, L. Liu, L. Jiang, P. Munroe, Z.H. Xie // Ceramics International. – 2013. – Vol. 39 (8). – Р. 9471–9481.
  11. Henry, P. Wear mechanisms of titanium and aluminium nitride coatings: A microtribological approach [Text] / P. Henry, M.-J. Pac, C. Rousselot, M.-H. Tuilier // Surface and Coatings Technology. – 2013. – Vol. 223 (25). – Р. 79–86.
  12. Cao, D. Investigation of acoustic emission and surface treatment to improve tool materials and metal forming process [Text] / D. Cao. – Dissertation Submitted to The School of Engineering of the University of Dayton (Dayton, Ohio), 2010. 116 р.
  13. Kang, J. Investigation of a novel rolling contact fatigue/wear competitive life test machine faced to surface coating [Text] / J. Kang, B. Xu, H. Wang, C. Wang // Tribology International. – 2013. – Vol. 66. – Р. 249–258.
  14. Gitis, N. Advanced mechanical testing of thin films and coatings [Text]: Congr`es JFT07 / N. Gitis, C. Dubegny //Lubrification et tribologie des revetements minces (22-23 mai, 2007, Poitiers, France), 2007. – Р.1–10.
  15. Kalogiannakis, G. Hemelrijck Identification of wear mechanisms of glass/polyester composites by means of acoustic emission [Text] / G. Kalogiannakis, J. Quintelier, P. De Baets, J. Degrieck, D. Van // Wear. – 2008. – Vol. 264 (3–4). – Р. 235–244.
  16. Myshkin, N. K. Devices for Tribotests at Micro/Nano Scale [Text] / N. K. Myshkin // Tribology in industry. – 2004. – Vol. 26 (3 – 4). – Р. 15–20.
  17. Piatkowska, A., Piatkowski, T. (2007). Measurement and analysis of acoustic emission in the tribological system ballon-disc. Diagnostyca, 4(44), 43–48.
  18. Hase, A., Wada, M., Mishina, H. (2008). The relationship between acoustic emissions and wear particles for repeated dry rubbing. Wear, 256 (5–6), 831–839.
  19. Benabdallah, H. S., Aguilar, D. A. (2008). Acoustic Emission and Its Relationship with Friction and Wear for Sliding Contact. Tribology Transactions, 51, 738–747.
  20. Raharjo, P. (2013). An investigation of surface vibration, airborne sound and acoustic emission characteristics of a journal bearing for early fault detection and diagnosis. A thesis submitted of the requirements for the degree of Doctor of Philosophy (The University of Huddersfield), 234.
  21. Fan, Y., Gu, F., Ball, A. (2010). Modelling acoustic emissions generated by sliding friction. Wear, 268 (5–6), 811–815.
  22. Filonenko, S. F., Stadnychenko, V. M., Stahova, A. P. (2008). Modelling of acoustic emission signals at friction of materials’ surface layers. Aviation, 12 (3), 87–94.
  23. Filonenko, S. F., Stadnychenko, V. M., Stahova, A. P. (2009). Definition of contact stress in friction units on the basis of the acoustic emission method. Aviation, 13 (3), 72–77.
  24. Xu, J., Xie, Z. H., Munroe, P. (2011). Effect of Cr alloying on friction and wear of sputter-deposited nanocrystalline (MoxCr1−x)5 Si3 films. Intermetallics, 19 (8), 1146–1156.
  25. Guo, J., Zhang, J., Yu, L., Wu, Z. (2013). ZhangInfluence of calcination temperature on structure as well as friction and wear behavior of CNx: H films on composite ceramic substrate. Thin Solid Films, 542 (2), 60–70.
  26. Xu, J., Liu, L., Jiang, L., Munroe, P., Xie, Z. H. (2013). Unraveling the mechanical and tribological properties of a novel Ti5Si3/TiC nanocomposite coating synthesized by a double glow discharge plasma technique. Ceramics International, 39 (8), 9471–9481.
  27. Henry, P., Pac, M.-J., Rousselot, C., Tuilier, M.-H. (2013). Wear mechanisms of titanium and aluminium nitride coatings: A microtribological approach. Surface and Coatings Technology, 223 (25), 79–86.
  28. Cao, D. (2013). Investigation of acoustic emission and surface treatment to improve tool materials and metal forming process. Dissertation Submitted to The School of Engineering of the University of Dayton (Dayton, Ohio), 116.
  29. Kang, J., Xu, B., Wang, H., Wang, C. (2013). Investigation of a novel rolling contact fatigue/wear competitive life test machine faced to surface coating. Tribology International, 66, 249–258.
  30. Gitis, N., Dubegny, C. (2007). Advanced mechanical testing of thin films and coatings. Congr`es JFT07: Lubrification et tribologie des revetements minces (22-23 mai, 2007, Poitiers, France), 1–10.
  31. Kalogiannakis, G., Quintelier, J., De Baets, P., Degrieck, J., Van, D. (2008). Hemelrijck Identification of wear mechanisms of glass/polyester composites by means of acoustic emission. Wear, 264 (3–4), 235–244.
  32. Myshkin, N. K. (2004). Devices for Tribotests at Micro/Nano Scale. Tribology in industry, 26 (3, 4), 15–20.

Downloads

Published

2014-06-26

How to Cite

Филоненко, С. Ф., & Нимченко, Т. В. (2014). Sensitivity of an acoustic emission to wearing of surfaces of a composite material. Eastern-European Journal of Enterprise Technologies, 3(9(69), 35–41. https://doi.org/10.15587/1729-4061.2014.23971

Issue

Vol. 3 No. 9(69) (2014): Information and controlling system

Section

Information and controlling system

License

Copyright (c) 2014 Сергей Федорович Филоненко, Татьяна Васильевна Нимченко

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.