Analysis of the natural composite material layers influence on the cantilever’s structural performance

Authors

DOI:

https://doi.org/10.15587/1729-4061.2022.253990

Keywords:

natural fiber, natural composite, finite element method, static structure, cantilever

Abstract

In this study, with their high strength-to-weight ratio, adaptability, and lack of corrosion, composite materials are widely used in aircraft construction and can be considered an acceptable metal substitute by all parties involved. Static load tests have been performed under identical conditions and stresses, but the layer sequence was changed. The Ansys workbench ACP-pre is utilized to analyze the data. Various deformations were found as a result of this. There are values of 14.265 and 0.1335 for the smallest z-direction deformation and for the overall strain in the composite 3 examples. Boundary conditions have been confirmed with 1,500 N as a resultant force with the static condition. The simulation results have been analyzed as a static condition. Four materials have been employed in different order to be investigated and these materials are Sisal, Pineapple, Jute, and Kenaf. The numerical results have been undertaken using the static structure of Ansys 16.1 Version tool. Geometry has been modeled and meshed using Ansys workbench. The model has been verified using convergence test. As the output, total deformation and von Mises stresses were investigated and explained accordingly. Numerical results stated that the maximum deformation due applied load was at the Z-axis. The maximum total deformation value is 1.254 mm and the minimum is 2.5 mm. Furthermore, von Mises stresses of the entire body have been calculated. The numerical results have shown the maximum result due to 1,500 N is 1.1 mPa. Eventually, the main aim has been achieved by employing total deformation and von Mises stresses accordingly

Author Biography

Ali hammoudi Abdul-Kareem Al wazir, University of Warith Al-Anbiyaa

Senior Lecturer

Department of Air-conditioning and Refrigeration Techniques Engineering

References

  1. Alsubari, S., Zuhri, M. Y. M., Sapuan, S. M., Ishak, M. R., Ilyas, R. A., Asyraf, M. R. M. (2021). Potential of Natural Fiber Reinforced Polymer Composites in Sandwich Structures: A Review on Its Mechanical Properties. Polymers, 13 (3), 423. doi: https://doi.org/10.3390/polym13030423
  2. Birman, V., Kardomateas, G. A. (2018). Review of current trends in research and applications of sandwich structures. Composites Part B: Engineering, 142, 221–240. doi: https://doi.org/10.1016/j.compositesb.2018.01.027
  3. Tran, P., Peng, C. (2020). Triply periodic minimal surfaces sandwich structures subjected to shock impact. Journal of Sandwich Structures & Materials, 23 (6), 2146–2175. doi: https://doi.org/10.1177/1099636220905551
  4. Sugiyama, K., Matsuzaki, R., Ueda, M., Todoroki, A., Hirano, Y. (2018). 3D printing of composite sandwich structures using continuous carbon fiber and fiber tension. Composites Part A: Applied Science and Manufacturing, 113, 114–121. doi: https://doi.org/10.1016/j.compositesa.2018.07.029
  5. Sergi, C., Sarasini, F., Russo, P., Vitiello, L., Barbero, E., Sanchez-Saez, S., Tirillò, J. (2021). Effect of temperature on the low-velocity impact response of environmentally friendly cork sandwich structures. Journal of Sandwich Structures & Materials, 24 (2), 1099–1121. doi: https://doi.org/10.1177/10996362211035421
  6. Akhavan, H., Ghadiri, M., Zajkani, A. (2019). A new model for the cantilever MEMS actuator in magnetorheological elastomer cored sandwich form considering the fringing field and Casimir effects. Mechanical Systems and Signal Processing, 121, 551–561. doi: https://doi.org/10.1016/j.ymssp.2018.11.046
  7. Sharaf, H. K., Ishak, M. R., Sapuan, S. M., Yidris, N. (2020). Conceptual design of the cross-arm for the application in the transmission towers by using TRIZ–morphological chart–ANP methods. Journal of Materials Research and Technology, 9 (4), 9182–9188. doi: https://doi.org/10.1016/j.jmrt.2020.05.129
  8. Raheemah, S. H., Fadheel, K. I., Hassan, Q. H., Aned, A. M., Turki Al-Taie, A. A., Sharaf, H. K. (2021). Numerical Analysis of the Crack Inspections Using Hybrid Approach for the Application the Circular Cantilever Rods. Pertanika Journal of Science and Technology, 29 (2). doi: https://doi.org/10.47836/pjst.29.2.22
  9. Sharaf, H. K., Salman, S., Abdulateef, M. H., Magizov, R. R., Troitskii, V. I., Mahmoud, Z. H. et. al. (2021). Role of initial stored energy on hydrogen microalloying of ZrCoAl(Nb) bulk metallic glasses. Applied Physics A, 127 (1). doi: https://doi.org/10.1007/s00339-020-04191-0
  10. Hamamed, N., Bouaziz, S., Hentati, H., Haddar, M., El Guerjouma, R., Yaakoubi, N. (2021). Numerical validation of experimental results for the dynamic behavior of sandwich structures. 2021 18th International Multi-Conference on Systems, Signals & Devices (SSD). doi: https://doi.org/10.1109/ssd52085.2021.9429366
  11. John, M., Schäuble, R., Schlimper, R. (2018). Fatigue testing of sandwich structures using the single cantilever beam test at constant energy release rates. 12th International Conference on Sandwich Structures ICSS-12: Proceedings, 205–207.‏ doi: https://doi.org/10.5075/epfl-ICSS12-2018-205-207
  12. Saseendran, V., Berggreen, C. (2018). Mixed-mode fracture evaluation of aerospace grade honeycomb core sandwich specimens using the Double Cantilever Beam–Uneven Bending Moment test method. Journal of Sandwich Structures & Materials, 22 (4), 991–1018. doi: https://doi.org/10.1177/1099636218777964
  13. Zhang, J., Yang, X., Zhang, W. (2018). Free Vibrations and Nonlinear Responses for a Cantilever Honeycomb Sandwich Plate. Advances in Materials Science and Engineering, 2018, 1–12. doi: https://doi.org/10.1155/2018/8162873
  14. Kardomateas, G. A., Yuan, Z. (2020). Closed form solution for the energy release rate and mode partitioning of the single cantilever beam sandwich debond from an elastic foundation analysis. Journal of Sandwich Structures & Materials, 23 (8), 3495–3518. doi: https://doi.org/10.1177/1099636220932900
  15. Pradeep, K. R., Thomas, A. M., Basker, V. T. (2018). Finite Element Modelling and Analysis of Damage Detection Methodology in Piezo Electric Sensor and Actuator Integrated Sandwich Cantilever Beam. IOP Conference Series: Materials Science and Engineering, 330, 012040. doi: https://doi.org/10.1088/1757-899x/330/1/012040
  16. Asyraf, M. R. M., Ishak, M. R., Sapuan, S. M., Yidris, N., Ilyas, R. A. (2020). Woods and composites cantilever beam: A comprehensive review of experimental and numerical creep methodologies. Journal of Materials Research and Technology, 9 (3), 6759–6776. doi: https://doi.org/10.1016/j.jmrt.2020.01.013
  17. Basu, A. K., Sah, A. N., Dubey, M. M., Dwivedi, P. K., Pradhan, A., Bhattacharya, S. (2020). MWCNT and α-Fe2O3 embedded rGO-nanosheets based hybrid structure for room temperature chloroform detection using fast response/recovery cantilever based sensors. Sensors and Actuators B: Chemical, 305, 127457. doi: https://doi.org/10.1016/j.snb.2019.127457 ‏
  18. Solly, J., Früh, N., Saffarian, S., Aldinger, L., Margariti, G., Knippers, J. (2019). Structural design of a lattice composite cantilever. Structures, 18, 28–40. doi: https://doi.org/10.1016/j.istruc.2018.11.019
  19. Zhang, W., Yang, J. H., Zhang, Y. F., Yang, S. W. (2019). Nonlinear transverse vibrations of angle-ply laminated composite piezoelectric cantilever plate with four-modes subjected to in-plane and out-of-plane excitations. Engineering Structures, 198, 109501. doi: https://doi.org/10.1016/j.engstruct.2019.109501
  20. Van Viet, N., Zaki, W., Umer, R. (2019). Bending theory for laminated composite cantilever beams with multiple embedded shape memory alloy layers. Journal of Intelligent Material Systems and Structures, 30 (10), 1549–1568. doi: https://doi.org/10.1177/1045389x19835954
  21. Viet, N. V., Zaki, W., Umer, R. (2018). Analytical model of functionally graded material/shape memory alloy composite cantilever beam under bending. Composite Structures, 203, 764–776. doi: https://doi.org/10.1016/j.compstruct.2018.07.041
  22. Solly, J., Frueh, N., Saffarian, S., Prado, M., Vasey, L., Felbrich, B. et. al. (2018). ICD/ITKE Research Pavilion 2016/2017: integrative design of a composite lattice Cantilever. Proceedings of the IASS Symposium 2018 Creativity in Structural Design.‏ Boston. Available at: https://www.researchgate.net/publication/326606101_ICDITKE_Research_Pavilion_20162017_Integrative_Design_of_a_Composite_Lattice_Cantilever
  23. Wu, J., Habibi, M. (2021). Dynamic simulation of the ultra-fast-rotating sandwich cantilever disk via finite element and semi-numerical methods. Engineering with Computers. doi: https://doi.org/10.1007/s00366-021-01396-6
  24. Mathew, R., Sankar, A. R. (2020). Temperature drift-aware material selection of composite piezoresistive micro-cantilevers using Ashby’s methodology. Microsystem Technologies, 27 (7), 2647–2660. doi: https://doi.org/10.1007/s00542-020-05013-2
  25. Guo, X., Wang, S., Sun, L., Cao, D. (2020). Dynamic responses of a piezoelectric cantilever plate under high–low excitations. Acta Mechanica Sinica, 36 (1), 234–244. doi: https://doi.org/10.1007/s10409-019-00923-5
  26. Dimitri, R., Tornabene, F., Zavarise, G. (2018). Analytical and numerical modeling of the mixed-mode delamination process for composite moment-loaded double cantilever beams. Composite Structures, 187, 535–553. doi: https://doi.org/10.1016/j.compstruct.2017.11.039
  27. Goryk, A. V., Koval’chuk, S. B. (2018). Elasticity Theory Solution of the Problem on Plane Bending of a Narrow Layered Cantilever Beam by Loads at Its Free End. Mechanics of Composite Materials, 54 (2), 179–190. doi: https://doi.org/10.1007/s11029-018-9730-z
  28. Shanmugam, L., Naebe, M., Kim, J., Varley, R. J., Yang, J. (2019). Recovery of Mode I self-healing interlaminar fracture toughness of fiber metal laminate by modified double cantilever beam test. Composites Communications, 16, 25–29. doi: https://doi.org/10.1016/j.coco.2019.08.009
  29. Suoware, T., Amgbari, C. O. (2022). A Review of the Fire Behaviour of Agro-Waste Fibre Composite Material for Industrial Utilization in Nigeria. Advances in Chemical and Materials Engineering, 278–300. doi: https://doi.org/10.4018/978-1-7998-9574-9.ch016
  30. Sampath, B., Naveenkumar, N., Sampathkumar, P., Silambarasan, P., Venkadesh, A., Sakthivel, M. (2022). Experimental comparative study of banana fiber composite with glass fiber composite material using Taguchi method. Materials Today: Proceedings, 49, 1475–1480. doi: https://doi.org/10.1016/j.matpr.2021.07.232
  31. Rao, S., Budzik, M. K., Dias, M. A. (2022). On microscopic analysis of fracture in unidirectional composite material using phase field modelling. Composites Science and Technology, 220, 109242. doi: https://doi.org/10.1016/j.compscitech.2021.109242
  32. Gupta, A., Hasanov, S., Fidan, I., Zhang, Z. (2021). Homogenized modeling approach for effective property prediction of 3D-printed short fibers reinforced polymer matrix composite material. The International Journal of Advanced Manufacturing Technology, 118 (11-12), 4161–4178. doi: https://doi.org/10.1007/s00170-021-08230-9
  33. Siddiqui, M. F., Khan, S. A., Hussain, D., Tabrez, U., Ahamad, I., Fatma, T., Khan, T. A. (2022). A sugarcane bagasse carbon-based composite material to decolor and reduce bacterial loads in waste water from textile industry. Industrial Crops and Products, 176, 114301. doi: https://doi.org/10.1016/j.indcrop.2021.114301
  34. Hao, C., Wang, X., Wu, X., Guo, Y., Zhu, L., Wang, X. (2022). Composite material CCO/Co-Ni-Mn LDH made from sacrifice template CCO/ZIF-67 for high-performance supercapacitor. Applied Surface Science, 572, 151373. doi: https://doi.org/10.1016/j.apsusc.2021.151373
  35. Shishvan, S. S., Dini Zarnagh, M. H., Deshpande, V. S. (2022). Energy dissipation and effective properties of a nominally elastic composite material. European Journal of Mechanics - A/Solids, 92, 104452. doi: https://doi.org/10.1016/j.euromechsol.2021.104452

Downloads

Published

2022-04-28

How to Cite

Al wazir, A. hammoudi A.-K. (2022). Analysis of the natural composite material layers influence on the cantilever’s structural performance. Eastern-European Journal of Enterprise Technologies, 2(1 (116), 16–23. https://doi.org/10.15587/1729-4061.2022.253990

Issue

Vol. 2 No. 1 (116) (2022): Engineering technological systems

Section

Engineering technological systems

License

Copyright (c) 2022 Ali hammoudi Abdul-Kareem Al wazir

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.